Question about Holden Rodeo

Open Question

Head bolt tension on Holden rodeo 3.5 v6 2004

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

billie17
  • 84 Answers

SOURCE: 2004 V6 3.5 Rodeo

"when the fuel pump kicks....it makes a very short duration sound....you can hear it....but in seconds it will be gone......as gasoline has made its way to the engine.........

if you cant hear any noise from the fuel pump......it could be that the fuel pump realy is bad........if you happen to change the relay....and it still does not work.....then it is the fuel pump. that is fried.......

about the water.....i am not shure......unless there was water in the gasoline itself....or somebody put water in there in purpose....

hope this helps...

Posted on May 16, 2009

stevenhurc
  • 450 Answers

SOURCE: torque settings for a holden rodeo 3.5 ra. Head

stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Posted on Dec 05, 2009

stevenhurc
  • 450 Answers

SOURCE: NEW CLUTCH SLIPPING ON 2004 V6 HOLDEN RODEO

did you bleed the hydralic clutch system on this vehicle? = air in system or not bleed properly.
most of the flywheels for this model were not to be machined...... however it is ok to machine these only slightly but you must machine the surface the clutch plate contacts with the same amount as the outer raised section the pressure plate bolts to.
new flywheels have painted stamped writing saying do not machine...so if hydralic system is ok find out about flywheel.
also may pay to check clamping force of pressure plate most clutch places can do this or some workshops that is if fingers on pressure plate are all at the same height, not broken or cracked..

Posted on Dec 05, 2009

dungeonfleet
  • 46 Answers

SOURCE: Head bolt torque settings...

Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Posted on Jan 16, 2010

dungeonfleet
  • 46 Answers

SOURCE: Head bolt torque settings

Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head bolt torque settings and order for 24litre petrol engine Austalia Holden rodeo Isuzu motor c24se Holden Rodeo 2003


this is USA forum
not a single HOLDEN here
not a one.
why ask us,
why not join , real forum that covers your country

http://www.planetisuzoo.com/

Mar 12, 2017 | Isuzu Cars & Trucks

1 Answer

Isuzu 2009 2.5 dtec torque sequence for cylinder head bolts?


NO car stated ! , in what country? no model car stated ,just and engine.
is this a diesel?
D-tec 2.5 , or 2.4L ?
is this a Holden engine?
do you mean D-max?
or D-TeQ?
you here>
http://www.gumtree.co.za/s-isuzu+d+tec/v1q0p1


we are usa forum there is no isuzu 2009s here, car or light pickups
get the book from your Isuzu dealer?
or google all day.
how to you know its torque and not angle set.?
only that is in the book, not sold here

badging magic(which one)????????????????
Chevrolet Colorado
Chevrolet D-Max
Chevrolet LUV D-Max
Holden Colorado
Holden Rodeo
Isuzu KB?
Isuzu LB?
Isuzu Rodeo?
Chevrolet T Series
GMC Canyon

Jan 22, 2016 | Isuzu Pickup Cars & Trucks

1 Answer

Remove airbag ra rodeo


First disconnect the battery and wate for 3 minutes for all power to drain, then take off the steering cover and then you will see the bolts to remove the air bag, to replace it just do all in reverse, hope this helps

Jul 08, 2014 | 2005 Holden Rodeo

1 Answer

Replace exhaust manifold gasket on a 3.2 litre Isuzu Holden rodeo motor


Take it off and have the face re-machined flat as when gaskets blow it is a sign that the manifold has warped. Use the correct gasket and tension the bolts in the correct order and to the correct tension. Be aware that on engines the manifold bolts are not all done up to the same tension to allow for manifold expansion

Jan 27, 2014 | Cars & Trucks

1 Answer

Will 1990 Holden rodeo gearbox fit in a 1998 Holden rodeo


if the engines are of the same family prefix Example ga or gh or what ever engine (from vin plate on fire wall) then yes . if not there may be differences in the bell housing bolts positions.

Dec 31, 2013 | Cars & Trucks

1 Answer

Cylinder head bolt tightening sequence for isuzu rodeo 1998


1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl

The Head Bolt Torque

Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence

1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl

The Head Bolt Torque

Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence

Jan 15, 2013 | 1990 Isuzu Spacecab

1 Answer

Torque settings for a holden rodeo 3.5 ra. Head


stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Dec 03, 2009 | 2004 Isuzu Rodeo

2 Answers

Head bolt torque settings...


Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Jun 28, 2009 | 2001 Isuzu Rodeo

1 Answer

Head bolt torque settings


Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Jun 27, 2009 | 2001 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...