Question about Cars & Trucks

Open Question

Head Bolt torque settings vw transporter t4 2002

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
the terrier
  • 94 Answers

SOURCE: head bolts torque settings

according to the manual its 22NM or 16lb/ft

Posted on Oct 26, 2008

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

martin538
  • 117 Answers

SOURCE: need head bolt torque settings for 200 landrover discovery 4.0 liter 241 cu.in.

Stage 1 20nm
Stage 2 +90 degrees
Stage 3 +90 degrees

Posted on Apr 13, 2009

  • 1 Answer

SOURCE: dont know the tyre pressure for my vw transporter

Way too low. I have the same vehicle. Pressure should be at least 55psi all round, depending on load.

Posted on Jun 09, 2009

sodeep
  • 3267 Answers

SOURCE: vw transporter t4 2.5tdi my speedo jumps

Both Odometer & Fuel gage needs to be replaced, else the potentiometer of both these need to replaced..........sodeep

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings


Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Nov 22, 2014 | 1996 Toyota Land Cruiser

1 Answer

1992 vw jetta 1.6 turbo diesel,what is the cylinder head bolt torque spec?


!st thing is get the revised head gasket (used on 1993 up) for this engine from VW or Felpro, always use new head bolts or a repeat failure will occur. Using the revised head gasket here is the procedure to torque the head down, it is done in stages. PLease go to this site and read the whole procedure.

Feb 07, 2012 | 1992 Volkswagen Jetta

1 Answer

What is the cyl head torque setting for 05 vw golf 1.4 fsi 16v


Cylinder head instructions

tdisline_358.jpg
Cylinder head torque setting for 2005 VW Golf 1.4 FSI
Renew bolts
Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

Mar 23, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

Flywheel torque setting vw transporter t30


VW Transporter 2.5 TDI-PD, (made year: 2003 ... 2007), engine code: AXD, 130 HP / 3500 rpm.
Important note: use new bolts!
Flywheel/driveplate torque setting: 60 Nm + 90 degrees.
Clutch to flywheel torque setting: 22 Nm.

May 21, 2010 | 2004 Volkswagen Eurovan

1 Answer

Wen fittin injectors in a vw pd engine wa settings is there


with out the correct aligining tools from vw you will need to measure from the side of the injector where the wedge slots in to the front part of the cam carrier molding in the head to use to re aligin the new unit the wedge bold is torqued to 20nm ( replace this bolt ) and the injector followers are torques to 20nm and 90 degrees the cam cover bolts are set to 20 nm

Apr 27, 2010 | 2001 Volkswagen new Passat

1 Answer

VW LUG NUT TORQUE SPECIFICATIONS 1965 BETTLE 5 BOLT


With the normal lug bolt with 17mm head, torque them down at 80 ft pounds. Replace them if looks to be worn out.

Apr 16, 2010 | Volkswagen Beetle Cars & Trucks

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...