Question about 2006 Kia Sedona

Open Question

Dashboard odometer display although car off

After turn the car off and removing the key the odometer continues to display, is this normal?

Posted by on

  • Amonr Feb 24, 2012

    The odometer display all the time,,,is this bad for battery,,,and what should i do
    Thanks

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset oil service required


Instructions1 Sit in the driver's seat of your ES 350. Push the "Odometer/Trip" button on the dash until "Trip A" appears on the display with the current mileage. 2 Hold down the "Odometer/Trip" button until the display flashes to indicate it has reset. 3 Insert the key into the ignition and turn it to the "ON" position. Do not start the car. Watch the odometer display for "000000." Turn the key to the "OFF" position and remove it from the ignition

Jun 26, 2014 | 2007 Lexus ES 350

1 Answer

Reset timing belt light on quantum 2.5 diesel


Try this: 1. Put the key in the ignition and turn it up one notch. The dashboard lights will not turn on. 2. Hold down your trip meter button next to the odometer. 3. When you are holding the trip meter button down, turn your key to the next notch. So, the dashboard lights will be on, but the car will not be started. Do not start the car. 4. Continue holding the trip meter button until the light turns off. You have now reset your Maintenance Required, or Maint Reqd, light

Jan 02, 2014 | 2007 Toyota Quantum 2.5

1 Answer

Past due service messege comes on need to take it off


Turn car off, hold in odometer reset button, turn key on (don't start) and wait for it to reset. Normally you will see small lines counting down on the odometer display.

Jun 18, 2013 | Honda Ridgeline Cars & Trucks

1 Answer

2006 toyota corolla maint. required light stays on. How do I make it go out after maint.


turn the key on. press the odometer/trip button until the odometer is displayed. turn the key off. press and hold the odometer button and turn the key to the run position (do not start). The odometer should change from a number to all dashes ( - - - - - - ). One by one the dashes will disappear then the display will change to all zeros and then will change to the regular odometer reading. Once the regular odometer is displayed let go of the button and turn the key off. The maintenance light will now be reset.

Jun 10, 2011 | Toyota Corolla Cars & Trucks

2 Answers

Hi, how do i put off ''maintenance required'' sign on my toyota camry 2007 car dashboard?Just did the servicing, the sign is still there?


with the key in the off position press and hold the odometer trip reset button on the dash. Turn the key to the run position while continueing to hold the reset button, do not start the car. The odemeter display should change to all dashes and then the dashes will start to go off one at a time. Once they are all out the odometer will display all zeros and then return to its normal display. Sometimes the trip A odometer needs to be displayed before starting and sometimes the trip B.

Your owners manual will give you some more insight if needed.

Sep 29, 2010 | 2007 Toyota Camry

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

1 Answer

How to remove maintenance required light?


With the key in the off position, hold down the trip reset button and turn the key on. You will see 5 lines across the odometer display that will count down. Continue to hold the button until all the lines have counted down and the light will be reset.

May 19, 2010 | 2004 Toyota Camry

3 Answers

Flashing light shows a car and a keyh inside


Thank You Very Much for The Maintenance Required Light Info, as far as the flashing car w the key inside. I'm not sure what key we have? When we bought it it only came with one key so we tried to make a duplicate, which ended up not working because we later found out it needs a chip (or probably what I hear as the smart key?) If the light is supposed to be on (and normal) why does it need reset?

The Maint Reqd light blinks after 4,500 miles, and stays ON continuously after 5,000 miles. This is to remind you that you need an oil change. Give the info from you about your key, you do not have a smart key. You have a transponder key. Off topic, but, FYI, a Toyota dealer can program a transponder key for you.
Back to the Maint Reqd light. Here is how you reset it:
Turn the key on.
Make sure that the odometer reads "ODO", and displays the total mileage traveled...If it displays trip a or trip b, push the black button by the odometer to make the display read ODO.
Turn the key off.
Press and HOLD the black trip reset button until advised to release it.
Turn the key ON. (keep holding th reset button down)
Observe the odometer display.
you will see 5 dashes, 4 dashes, 3 dashes, 2 dashes, 11 dash, followed by five zeros, and the total mileage you started with will re-display.
Release the button.
Turn the key off.

Regarding the flashing light with the car & the key: This is the indicator to show potential theives thatyou vehicle has a sophosticated security system, and it CAN NOT be started by "hot-wiring" it. The flashing light is normal, and consumes no battery power. I hope that this helps you understand these two items better. Thanks for choosing FixYA, and the graciousness of a FixYa rating for my solution to you would be greatly appreciated. Glad to be of assistance; please feel free to call upon me anytime. Have a great day.

Nov 05, 2008 | 2007 Toyota Avalon

1 Answer

Maintenance light


on dashboard press ODO METER until normal KM reading appears(not trip AorB) after that turn off the ignition.
then with the odometer button pressed (hold it pressed), turn on the ignition ON (don't release the odometer button!) .many underscore (like - - - - - - -)will appears & start disappearing
keep the odometer button pressed until the maintenance light goes off

Oct 04, 2008 | 2006 Toyota Corolla

Not finding what you are looking for?
2006 Kia Sedona Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...