Question about Cars & Trucks

Open Question

How can i test to determine if my input turbine speed sensor is bad?????

How can i do the trouble shoot????

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Molson02536
  • 3854 Answers

SOURCE: turbine input speed sensor

NO the sensor is out side the transmission. And it might just be a bad connection due to being out in the eliments. On the 3.1 your going to have to jack up the car to get to it from underneath and you should see it on the passenger side may be on top, Sorry been awhile and carful not to brake the clips that hold the wire to the sensor when disconnecting.
Good luck and hope this helps

Posted on Apr 09, 2009

  • 316 Answers

SOURCE: input/turbine speed sensor circuit

Your speed sensor, is located on top of the transaxle, near the starter. To access it, remove the battery, then remove the battery tray (4 10mm bolts). You will see wires coming from the lower oxygen sensor, and they snap into the bracket that holds the speed sensor in place. The actual speed sensor has a 2 wire clip on it, and is held in place by the bracket and a 10mm bolt.

Posted on Apr 20, 2009

  • 257 Answers

SOURCE: I have a Volkswagen TDI 1.9L - diagonistic fault

That code also reads as: Transmission Input Speed Sensor (G182): Circuit Malfunction

The sensor is located inside the transmission. Not exactly a DIY type of job...

Posted on Jul 07, 2009

  • 1 Answer

SOURCE: I have a code p0715, which is the input turbine speed sensor

Have the same problem with the input speed sensor. The part, so far, is only made by Mitsubishi (Part No. 8651A111) and cost about $110 (w/ tax in TX).

Posted on Oct 07, 2009

  • 1 Answer

SOURCE: Where does the input/turbine speed sensor goes?

when my 2001 oldsmobile aurora switch gears my transmisson jumo does that sound like i need a input turbine sensor?

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Jeep Grand Cherokee. DTC P2767. Is the probable cause in the transmission or external?


the code means.
to do the tests listed in the fsm. book, not guess.
we do the tests, and find out if the cause in in the transmission
the TCM or the TCM sensors or the solenoid drivers or solenoids
or the actual transmission internals.
why guess? why ask folks to guess. who are blind.?
ever seen the book, and read , the chapter on A/t trans on car tests?
alldata.com or
free
wk jeep
here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

official.
https://www.techauthority.com/en-US/Pages/FacetSearchResults.aspx?make=Jeep&year=2006&model=GRAND+CHEROKEE+BASE&engine=3.7L+MAGNUM+V6&producttype=Service+Manuals&ptCatId=3083

i guessed drive line... so....

the book hints at....
- Faulty Input Speed Sensor 2 ,.is dead.
- Input Speed Sensor harness is open or shorted
- Input Speed Sensor circuit poor electrical connection

The Input Speed Sensor 2 is one of the two hall effect speed sensors that are used by the Transmission Control Module (TCM) to calculate the transmissions turbine speed. Since the turbine speed could not be measured directly, two of the drive elements are measured. Two input speed sensors are required because both elements are not active in all gears.

May 14, 2015 | Jeep Cars & Trucks

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

Where does the turbine input shaft speed sensor go on a 2010 cevy malibu Lt


Chances are that this sensor is located in the transmission or has access to it outside the housing.Take the car to a transmission specialist and have them give you an estimate.Most dealerships these days don't even do trany work anymore so save yourself some money and go directly to someone who can help you.good luck

May 22, 2014 | 2010 Chevrolet Malibu

1 Answer

Input turbine speed sensor location


Hi Mario, I may be behind times, but believe the sensors you're referring to are the turbine pressure sensors. There are usually two, mounted onto he turbo inter-cooler. Regards John.

Apr 21, 2014 | 2002 Honda Odyssey

1 Answer

Speed sensor cavalier po717


Not sure which sensor that is. Code 717 is for a turbine input sensor which could be the torque converter or the turbine inside the transmission. Either one could be considered input.
You would need a shop manual to get the test procedures for that circuit.

Sep 01, 2013 | 1998 Chevrolet Cavalier

1 Answer

Lost pwr for takeoff, and gauges all going haywire and overcharging battery


Did the overcharge or voltage regulator problem go away with the new ECM in it? If so the transmission code.. (turbine speed sensor input) code is probably another problem that the Jeep has.. and the ECM will not fix that, but the input speed sensor that it may need is not very expensive.

Jan 29, 2013 | 2000 Jeep Cherokee

2 Answers

P0715 turbine input shaft speed sensor circuit what that mean


P0715 MAZDA - Input Turbine Speed Sensor Circuit Malfunction.


xicon.jpghttp://engine-codes.com/p0715_mazda.htmlForum CodePossible causes- Transmission speed sensor circuit is open or shorted.
- Poor transmission speed sensor circuit connection
- Faulty transmission speed sensor When is the code detected?Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

Jul 04, 2012 | 2001 Mazda Tribute

2 Answers

Trouble code for Turbine Speed Sensor input shaft no signal & trans won't shift from 2nd gear started out being intermittent now stuck in 2nd.


You will need your transmission tested or checked out

The Turbine Sensor may be the one closest to the engine
and is any indication of input speed from the converter,
vs: the other trans sensors that are farther back on the case.

Now the issue is, can you get your hand between the floor pan
to change it,if it is bad.

Dec 03, 2010 | 2006 Mercedes-Benz CLK 500

2 Answers

I got a P O 717 code what is it ???


P0717: Input/Turbine Speed Sensor Circuit No Signal.
This code shows because the computer isn't getting any signal from the sensor. Either the sensor is dead or there's a circuit issue (bad wiring, etc).

The Input/Turbine Speed Sensor is the sensor the computer uses to to monitor the the efficiency of the transmission. The computer reads the speed from the input shaft and compares it to the speed of the output shaft. If the speed is off it attempts to correct it by boosting the fluid pressure to compensate. When that fails it trips the P0717 error code. In most cases either the sensor is dead or there's a problem in the wiring harness.

There are issue of intermittent connection trouble with this circuit. That would cause the on off problem.
Hope this helps.

Nov 11, 2009 | 2003 Buick LeSabre

1 Answer

Transmission code error P2716


The computer wants to know if the transmission is working properly. So it reads the speed of the input shaft and compares it to the speed of the output shaft. It knows which gear you're in because it commanded the transmission to shift into that gear. The turbine speed refers to the torque converter. That's the device that transfers power from the engine to the transmission. Think of two fans facing each other. Turn on one fan and the blades on the other fan will spin. The fan that ISN'T turned on is the turbine. So, with the input shaft or turbine speed, the gear selection, and the output speed, the computer can calculate how efficiently the transmission is working. If the speed is off, it knows that something is slipping inside the transmission. It can then try to boost the fluid pressure to compensate. If that doesn't work, it sets a different trouble code, usually a P0716 code means that the computer has detected a value for the input sensor that's either out of range (way too high or too low), or there's a circuit issue (bad wiring, etc. Should probably get it to a repair shop ASAP before damage is done.

Sep 19, 2009 | Toyota Corolla Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...