Question about Cars & Trucks

Open Question

Bleeding procedure for 2001 ford escape - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: how to bleed the brakes for 2001 ford taurus

Please don't forget to rate:


Bleeding The Brake System Bleeding When any part of the hydraulic system has been disconnected for repair or replacement, air enters the lines causing spongy pedal action (because air can be compressed and brake fluid cannot). To correct this condition, it is necessary to bleed the hydraulic system to ensure all air is purged.
Always begin bleeding the brake system from the furthest wheel cylinder or caliper from the master cylinder; the right rear.
NOTE: The right side of the vehicle is the passenger side. The sides of the vehicle are determined from the driver's perspective. This reference is taken from sitting in the driver's seat, facing forward.
Maintain a full reservoir during the bleeding operation. Never use brake fluid that has been drained from the hydraulic system, or from an open container, no matter how clean it is. Always use brake fluid from a new, sealed container. The front and rear reservoir will drain as the front or rear brakes are bled.

  1. Park the vehicle on a level surface. Place the vehicle in PARK (automatic) or REVERSE (manual) with the engine OFF, and apply the parking brake. Chock the rear wheels to prevent vehicle movement. NOTE: Wheel chocks may be purchased at your local auto parts store, or a block of wood cut into wedges may be used.
  2. Loosen the lugnuts from all four wheels, but do not remove the lugnuts until the vehicle is raised and supported properly.
  3. Use an approved jack and raise the vehicle high enough to place jack stands under all four corners of the vehicle. Place the jack stands under the frame or axles of the vehicle. Ensure that the front of the vehicle is raised higher than the rear.
  4. Remove the wheels from the vehicle.
  5. Clean all dirt from around the master cylinder fill cap. Remove the cap and fill the master cylinder with brake fluid until the level is within 1/4 in. (6mm) of the top edge of the reservoir.
  6. Clean the bleeder screws at all four wheels. The bleeder screws are located on the back of the brake backing plate (drum brakes) and at the top of the brake calipers (disc brakes).
  7. Attach a length of rubber hose over the bleeder screw and place the other end of the hose in a plastic jar.
  8. Have an assistant place and hold pressure on the brake pedal.
  9. Open the bleeder screw 1/2 - 3/4 turn. As the bleeder is opened, the brake pedal will travel to the floor. Have the assistant inform you when the pedal has bottomed out. NOTE: Do not remove pressure from the brake pedal once it is bottomed out. No movement to the pedal should occur until the bleeder is closed and the assistant is made aware of the situation. Failure to do this will draw more air into the system.
  10. Close the bleeder screw and tell your assistant remove their foot from the brake pedal. Continue this process to purge all air from the system.
  11. When bubbles cease to appear at the end of the bleeder hose, tighten the bleeder screw and remove the hose.
  12. After bleeding each wheel, check the master cylinder fluid level and add fluid accordingly.
  13. Repeat the bleeding operation at the remaining three wheels, ending with the one closet to the master cylinder. The pattern is, RR, LR, RF, LF.
  14. Fill the master cylinder reservoir to the proper level and install the reservoir cap.

Posted on Jul 22, 2009

Ad
landsend
  • 1066 Answers

SOURCE: ABS on 2001 Ford Escape .

could you have a low or odd sized tire on the car?  have you bumped a sensor?  Is the light on?

Posted on Apr 01, 2009

motor1258
  • 6674 Answers

SOURCE: what is throubleshot p0113 at ford escape 2001

Intake air temperature sensor faulty. Depending on what engine, may be in side of air cleaner or air intake hose , or may be part of the MAF (mass airflow ) sensor. You can try cleaning MAF with tuner cleaner from radio shack or TV repair place.

Posted on Jun 28, 2009

bschilz
  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

  • 4861 Answers

SOURCE: radio unlock procedure for 2001 ford escape

Ford Code Entry Instructions

Once the unit has been turned on the display will show ' CODE - - - -'

Press preset [ 1 ] repeatedly for the first digit
Press preset [ 2 ] repeatedly for the second digit
Press preset [ 3 ] repeatedly for the third digit
Press preset [ 4 ] repeatedly for the third digit

To save the code press the [ 5 ] key to accept.

The set should now operate

Posted on Sep 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace thermostat '02 ford escape 3.0l


1. Drain the engine cooling system.
2. Remove the air cleaner intake pipe.
3. Release the clamp and disconnect the upper radiator hose from the thermostat housing.
4. Remove the bolts and the thermostat housing.

o To install, tighten to 10 Nm (89 inch lbs.) .

5. Remove the thermostat and the O-ring seal.

o Discard the O-ring seal.

6. To install, reverse the removal procedure.

o Install a new O-ring seal and lubricate it with clean coolant

7. Fill and bleed the cooling system.
25486479-lh4p3qx2aut5mcwq32hs4n0f-5-0.gif

Feb 26, 2015 | 2002 Ford Escape

1 Answer

How to bleed brakes on 2003 safari rwd.


Same as you always have on any vehicle

Need a helper,the motor running & you start at
the RR & work your way to the front

May 23, 2014 | 2001 Ford Escape

1 Answer

2001 ford escape wont start


Hi,
Your Escape's battery is dead and needs replaced.

GL,
Td

Jan 28, 2013 | 2001 Ford Escape

1 Answer

I need to replace my iac valve/sensor on my 2001 ford escape v6. where will i find it hiding?


Why replacing? Codes/ Check Engine Light on?

adobe.gif Printable View (263 KB) TSB
06-11-7
  • 2001-2005 ESCAPE 3.0L UNSTABLE IDLE - 2001-2003 ESCAPE 3.0L AUTOMATIC TRANSAXLE SHUDDER - MEXICO ONLY
Publication Date: May 25, 2006
FORD: 2001-2005 Escape
ISSUE: Some 2001-2005 Escape vehicles equipped with a 3.0L engine may exhibit idle speeds outside the specified range. Some 2001-2003 Escape vehicles equipped with a 3.0L engine and CD4E automatic transaxle may exhibit a transmission shudder.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE
  1. If the concern is a 2001-2005 Escape with idle speeds outside the specified range:
    1. Install a new idle air control (IAC) valve with jumper harness included in the kit. The new Denso brand IAC will be installed with the electrical connector facing the opposite direction of the original (Hitachi) valve which is why the jumper harness is required. The original (Hitachi) IAC connector faces the front of the vehicle while the new Denso IAC connector faces toward the rear of the vehicle.
    2. Referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the powertrain control module (PCM) using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com.
  2. If the concern is a 2001 - 2003 Escape with transaxle shudder, drain, flush and refill the transmission fluid with MERCON® Multi-Purpose Automatic Transmission Fluid. Then, referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the PCM using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com.
  3. When reprogramming the PCM use blank path programming. Select the proper file from the chart and manually enter the PCM part number or tear tag number to obtain the updated calibration file.
To Perform Blank Path Programming:
  1. Connect WDS/IDS to vehicle.
  2. Select "16 pin", select "All others, except those below", press TICK.
  3. Screen shows installation of cable, press TICK.
  4. Screen shows to turn ignition ON. DO NOT TURN IGNITION ON. Press TICK.
  5. Screen shows progress bar, then screen tells you "No communication can be established with the PCM" and asks you if you want to retry? Select "NO". With the ignition key still OFF, press TICK.
  6. Screen shows to turn ignition ON. Keep ignition in the "OFF" position, press TICK and you will be asked to cycle the key "ON" and "OFF" a few times. Please keep the key position in the "OFF" position through the key cycles.
  7. Screen will show "The diagnostic tester is unable to communicate with this vehicle." You will be prompted to "select a vehicle from the vehicle list", press TICK.
  8. A list of vehicles will be displayed, select ALL OTHERS, and press TICK.
  9. Screen shows "To enable WDS to reprogram the PCM with the correct calibration", enter one of the following: Vehicle Calibration number (7 digits), Tear Tag number (4 digits), or PCM part number, press TICK.
  10. Highlight the box next to the selection chosen, and enter ONLY ONE of the selections listed above. Press TICK.
  11. Follow and answer correctly all remaining screens. Once PCM is reprogrammed communication should be reestablished and PATS system can be reset (if necessary) per Workshop Manual, Section 419-01.

PART NUMBER PART NAME 5L8Z-9F715-AA Idle Air Control Valve XT-2-QDX MERCON® Multi-Purpose Automatic Transmission Fluid
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage
DEALER CODING BASIC PART NO. CONDITION CODE 9F715 42

tb8487b.gif
Figure 1 - Article 06-11-7



tb8488b.gif

Sep 07, 2011 | 2001 Ford Escape

1 Answer

Where are the spark plugs for the 2001 v6 ford escape


Three in the front under the engine cover, then under the coil packs, there are three more in the rear of the engine at which you must properly remove the intaker manifold and do this by procedure or risk warping the head and manifold. If you must ask, I highly suggest taking this to a pro. Sorry

Jul 13, 2011 | 2001 Ford Escape

1 Answer

Radio unlock procedure for 2001 ford escape cassette player please I have the code...thanks


Ford Code Entry Instructions

Once the unit has been turned on the display will show ' CODE - - - -'

Press preset [ 1 ] repeatedly for the first digit
Press preset [ 2 ] repeatedly for the second digit
Press preset [ 3 ] repeatedly for the third digit
Press preset [ 4 ] repeatedly for the third digit

To save the code press the [ 5 ] key to accept.

The set should now operate

Sep 09, 2010 | 2002 Ford Escape

2 Answers

Need a diagram pitcure of firing order for a 2001 Ford Escape


you didn't say which engine so here it is for both
2001 Ford Escape 2WD
2.0 liter DOHC L4 VIN "B" 92714651.gif
2001 Ford Escape 2WD
3.0 liter V-6 VIN "1" 92725094.gif

Jul 18, 2009 | 2001 Ford Escape

1 Answer

ABS on 2001 Ford Escape .


could you have a low or odd sized tire on the car?  have you bumped a sensor?  Is the light on?

Apr 01, 2009 | 2001 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...