Question about 2004 Chevrolet Monte Carlo

Open Question

How do you take off a oil pan for a 04 monte Carlo (What needs to be removed to pull it off)?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: need to replace alternator on 1998 chevrolet monte carlo

Nope, it has two bolts one towards the front and one at the back underneath. Be careful of the one in the back as the nut is tricky to get on. You don't need to remove the bracket.

Posted on Feb 18, 2009

Ad
  • 6982 Answers

SOURCE: replac 2003 monte carlo oil pan gasket

To remove the oil pan on any vehicle, first remove anything obviously in your way...starter, exhaust pipe etc. Then disconnect the engine mounts and raise engine to gain sufficient clearance between frame and pan. You cannot support the engine from under the pan so either use a fixture above the engine or put blocks between mounts and engine to support it. After all rail bolts have been removed, remember that the oil pump pickup will interfere with removal somewhat but pan can be maneuvered around it. Anything preventing you from getting the pan out will then need to be removed or moved as they are identified. Be careful when raising the engine that you do not break anything above it as it comes up.

Posted on Jun 09, 2009

  • 141 Answers

SOURCE: remove the power steering pump pulley on a 2003 monte carlo

you can either remove the steering pump to gain access,if there is no holes in PS pump pulley,you can rent a pulley puller....can be a ***** to get in and use them though....I will drill a hole in it for next time whenever I replace a pump on cars without ....

Posted on Aug 09, 2009

  • 462 Answers

SOURCE: OIL PAN GASKET LEAK

The engine has to be supported and the cradle under the engine has to be removed. After everything is reinstalled the front end has to be realigned.

Posted on Sep 13, 2009

Testimonial: "Thanks for your help, but i think i need a little more info. before tring this."

  • 1 Answer

SOURCE: 95 Monte Carlo Idle Fast and Have low oil pressure

95 monte carlo is idling high we just replaced the intake manifold gasket. How do I fix this and could I have caused it.

Posted on Sep 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace oil pump on 01 monte carlo ss


If the oil pan will clear the steering components without jacking up the engine then drop the pan and unbolt the oil pump. You'll need to get a new pan gasket for the oil pan too.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

HOW TO REMOVE 4T60E TRANSMISSION FROM A 96 Z34 MONTE CARLO?


You don't have to pull it to replace the TCC. Remove the pan and you can access the TCC solenoid. 40b12bb6-08f8-4f1c-b959-9bfe6f7b08fb.gif

Aug 06, 2014 | 1996 Chevrolet Monte Carlo

1 Answer

Install timing chain 1999 monte carlo


you need to buy haynes repair manual it will show you the camshaft sprocket and crankshaft sprocket timing marks and manual will show and tell you how to remove timing chain.you need lots of tool and a engine light support engine you have to remove oil pan so bottom part timing cover will seal correctly if you dont remove oil pan bottom timing cover seal will be in a bind you will have oil leak.

Aug 19, 2012 | 1999 Chevrolet Monte Carlo

2 Answers

I have a 2003 monte carlo ss i fixed the intake gasket but now the car losses oil pressure i changed the oil and put in 10 w 40 new filter found out i use the wrong oil so i changed the oil to 10 w 30...


It is hard to say without being able to check the vehicle. It is possible that gasket material, silicone, etc. ended up inside the engine duing the repairs and is now stuck in your oil pump screen. It is also possible that you really do not have low oil pressure and the gauge is "lying" to you.

The way to find out is to remove the oil pressure sending unit and install a manual gauge. Take an actual pressure reading to see if the car's gauge is accurate. If it is not accurate, you most likely need a new sending unit. If you find that the oil pressure is actually low, then it is time to pull the oil pan and look inside to see what kind of damage or debris is in the oil pan.

Mar 18, 2012 | 2003 Chevrolet Monte Carlo

1 Answer

My car is leaking oil, it is from the basepan. Is


By basepan, do you mean the oil pan? The 3800 engine in your monte has problems with the pan gasket leaking, or the pan itself rotting. You can do it yourself, but it requires either lifting the engine up about 6 inches, or dropping the cradle.

If you can do that, then yes, you can change it yourself, otherwise, you will need to take it to the shop. I've done 3 of them and it is a pain. Unless you're really into being a mechanic, take it somewhere.

Apr 09, 2010 | 2000 Chevrolet Monte Carlo

1 Answer

OIL PAN GASKET LEAK


The engine has to be supported and the cradle under the engine has to be removed. After everything is reinstalled the front end has to be realigned.

Sep 13, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

How do i drop an oil pan on a 1995 monte carlo z34. 3.4 l . took bolts off, couldn't get oil pan to come off. what is the easiest way to get it loose?


I use a metal putty knife along the edges of the pan. Just tap the knife with anything you can fit next to it and follow the seam.

If you did not pull the motor make sure the pan will clear the frame. Sometimes you can turn the crank to get clearance but you still have the oil pickup in the way.

Jul 07, 2009 | 1995 Chevrolet Monte Carlo

1 Answer

Replac 2003 monte carlo oil pan gasket


To remove the oil pan on any vehicle, first remove anything obviously in your way...starter, exhaust pipe etc. Then disconnect the engine mounts and raise engine to gain sufficient clearance between frame and pan. You cannot support the engine from under the pan so either use a fixture above the engine or put blocks between mounts and engine to support it. After all rail bolts have been removed, remember that the oil pump pickup will interfere with removal somewhat but pan can be maneuvered around it. Anything preventing you from getting the pan out will then need to be removed or moved as they are identified. Be careful when raising the engine that you do not break anything above it as it comes up.

Jun 09, 2009 | 2003 Chevrolet Monte Carlo

1 Answer

Oil pan


You dont need to change the oil pan.Goto an auto parts store and ask for a universal drain plug.They come in a red package and the word 'HELP' on them.

Jul 19, 2008 | 2001 Chevrolet Monte Carlo

Not finding what you are looking for?
2004 Chevrolet Monte Carlo Logo

Related Topics:

563 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...