Question about 1987 Ford Ranger

Open Question

Where should the timing marks be on a 1987 ford ranger 2.0L

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
shop242
  • 214 Answers

SOURCE: Timing Marks-99 Ford Ranger

Its Dot to Dot.. Crank Pointer Up.. CAm Pointer down.. DOT 2 DOT.. Thank you

Posted on Mar 15, 2009

Ad
Louie_3006
  • 79 Answers

SOURCE: need timing marks ford ranger

The timing marks are on your timing belt cover. There is a little circle on the bottom right of the cover near the harmonic balancer that you can pop out to see if your distributor accesory gear is in the correct position. The camshaft has a triangle on the inside of the gear that you can line up with this accesory gear. The bottom of the timing belt cover has your timing tick marks and you may have to clean off this rectangular piece that is sticking out on the cover to see the marks. A good timing gun and remembering where the number 1 cylinder on your distributor is a good start to timing your motor. Refer to a Haynes Manual and it will give you a good guide line on how to time your motor with TDC. I hope you have good luck with this!

Posted on May 18, 2009

  • 1129 Answers

SOURCE: 1987 Ford Ranger stuck in 4 wheel drive!!

Chances are the linkage for the transfer case is out of adjustment try loosening the adjuster bolt and put the 4WD shifter into the position 4WD high or low (depending upon which position it's lockup in) then lock down the adjuster bolt, try to shift out of 4wd sometimes you need to go forward and backward with the vehicle to get it out of 4wd, when you get it out of 4wd you may have to fine tune the adjustment to get it to engage and disengage smoothly it's a trial and error thing keep resetting adjuster until you get the desired effect.

Posted on Jul 02, 2009

motor1258
  • 6674 Answers

SOURCE: timing marks for 1989 ford ranger

which engine?

Posted on Jul 18, 2009

  • 1757 Answers

SOURCE: what do the timing belt marks line up on a 94 ford

My apologies for the delayed response. I am going back to answer unanswered questions.
CLICK
on the following LINK. It has the Timing Belt & Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/1994/make/ford/model/ranger/1994_ford_ranger_timing_belt_diagram_marks.htm

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the timing marks on 87 ford ranger 4 cylinder


If you open the hood and look down behind the fans there is a pulley about six inches in diameter. This will have notches running along te edge as well as a bracket coming off that will have a notch through it. These are your timing marks. You will need a timing gun and it also helps if you have white out and you can mark the pulley. With that engine I believe you want to be 10-11 btdc. Good luck.

Mar 16, 2015 | 1987 Ford Ranger

1 Answer

Vaccum hose diagram for 1987 ford ranger needed


CHeck this diagrams...


2_16_2012_2_02_19_pm.jpg


Fig. 14: Vacuum hose routing-1987 2.9L engine - zoom link here


2_16_2012_2_05_56_pm.jpg

Fig. 13: Vacuum hose routing-1987 2.3L engines - zoom link here

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 16, 2012 | 1987 Ford Ranger

1 Answer

What are the timing marks 1987 ford ranger 2.3


star with your crank pulley, fuond a notch mark it (witeout woks fine) then botton of timign cover mark 0, bring them together and check your distribuitor rotor points to spark plug cable for piston #1 first front to back, if not match your timimg belt jumped.

Oct 02, 2010 | 1987 Ford Ranger

1 Answer

How do i take the timeing belt of a 87 ford ranger


The 87 Ford Ranger 2.9L is chain driven. They dont have a timing belt. Now the 2.3L 87 Ranger were belt driven.

Sep 16, 2010 | 1987 Ford Ranger

1 Answer

Timing has jumped


Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need.

http://www.2carpros.com/car_repair_information/year/1987/make/ford/model/ranger/1987_ford_ranger_timing_belt_diagram_marks.htm

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com

Mar 20, 2010 | 1987 Ford Ranger

1 Answer

Im looking for the timing marks for a 1987 ford ranger 2.3l 2wd can you help me i have no manuel and no money


What are trying to do, change the belt or just set the timing? The timing marks should be on the left side (drivers side) near the front pulley. There is a notch or line on the pulley and the scale is on the timing cover. If you are trying to change the timing belt, you have to remove the fan and water pump pulley, then crank pulley and the timing cover. If you are changing the belt, here's a helpfull hint loosen the tensioner bolts, one 13mm one 17mm, then pull or push on the belt to force the ternsioner back as far as you can and tighten the 13mm bolt. Now you can take the old belt off and put the new belt on with ease. You have to set the crank at zero, I think the key in the crankshaft is straight up at this point, there is a diamond shaped mark on one of the teeth of the pulley, that lug has to line up with the notch in plastic behind the pulley. At this point you want the arrow on the cam pulley to point to the mark on the inner cover (about 6 o'clock) and the rotor in the distributor should point to the "V" notch in the pick up coil assembly (about 6 o'clock). Good luck!

Dec 03, 2009 | 1987 Ford Ranger

1 Answer

Camshaft timing mark crankshaft timing mark


Belt covers need to be on. Timing mark on crankshaft (while on compression stroke) should line up with TDC mark on cover. then Camshaft mark, needs to line up by looking through access hole of cover, and align mark on cam sprocket with pointer on inside of belt cover.

Oct 22, 2009 | 1987 Ford Ranger

2 Answers

We are trying to find the timing marks on the engine on a 1987 ranger. Does anyone know where to find them?


depends on what size engine it has the 2.3 or 2.0 the cranshaftmark will be on the timing cover the camshaft will be the pointer below the gear. the gears will have a dot or arrow on them just align them before you put the new belt on.

Jun 09, 2009 | 1987 Ford Ranger

2 Answers

Putting a 1987 Ford Ranger in Time


you have to put the #1 piston at tdc, then put the cam in at the mark.

Nov 30, 2008 | 1987 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...