Question about Mitsubishi Cars & Trucks

Open Question

Mitsubishi shogun pinin wont rev above 2000 rpm

Mitsubishi shogun pinin 2.0 GDI 2001. Car starts ok,idles ok but will not rev above 2000 rpm when accelerating. I have already cleaned the throttle body and replaced the microfilters in the high pressure fuel pump i have also stripped and cleaned the injectors and also replaced the microfilters in them too. i have replaced all spark plugs and checked the coils for correct operation i have changed the airfilter and the MAF meter. i have had only two dtc flag up p0190 which is low pressure in the fuel rail, i changed all filters and cleaned out the fuel rail and the injectors and this fault has now cleared the other code was p1221 which only came up once and when cleared never came back. it will rev to 4000 rpm if i press the accelerator very slowly but wont go above 2000 if i press it down normally, also the engine pops as if its misfiring when i press down normally but does no when i press down slowly any ideas???

Posted by on

  • stuart mann Aug 12, 2013

    Hi did you solve your problem as i have exactly the same issue with my 2.0 GDI Pinin


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

What causes my 2001 mitsubishi GDI car to be firing only on number 2 and 3 cylinders

Check to see if #1 &4 use a common coil pack. If so, = likely culprit.

Jan 15, 2015 | Mitsubishi Cars & Trucks

2 Answers

If a relay clicks 7/8 times after switching on ignition my pinin will not start

normally dont get clicking on a fuel pump normally its the starter selinoid that clicks can you hear the pump with ignition on or only when it starts i would replace the relay replaced first cheapest thing to replace first hope this helps ivan

Oct 08, 2012 | Mitsubishi Pajero Cars & Trucks

2 Answers

My car is Pajero Pinin GDI, when the car is cold, the RPM will be good, but when it got warm, the RPM will go down and the car will start shaking, my mechanic told me that i have poor idle, how to fix this...

I had the same poor idleing car was stoping at every junction,so yesterday i had the throttle body off and i have cleaned it inside by the flap including the flap the muc on there was unbelieveable now the car drives smooth no stalling issue no poor idleing!
Make sure u DONT take the sensors off either side otherwise u get in more problems.
Good luck.

Apr 13, 2010 | 2000 Mitsubishi Galant

1 Answer

Hi, i got error code 421, what that can be??? mitsubishi shogun pinin

Your catalytic convertor is clogged you have to change before is damages ur o2 sensors

Feb 23, 2010 | 2001 Mitsubishi Montero

1 Answer

Mitsubishi pinin fault code P0421

yes this is your catalytic convertor is clogged you have to change before is damages ur o2 sensors

Feb 12, 2010 | 2001 Mitsubishi Montero

3 Answers

Mitsubishi Pinin 1800 GDI Automatic Year 2000 Had to remove battery for recharging. We now have problem with intermittent low revs on tick-over and stalling. Please advise.

try resetting the base idle,disconnect the battery,leave for ten minutes,reconnect the battery,start the car and do not rev the engine for ten minutes.hope this helps

Sep 13, 2008 | Mitsubishi Montero Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides