Question about 2002 Kia Sedona

1 Answer

How can I read my own code

How do I tell what my car is reading for a code

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

There are products available which run on a laptop that will allow you to read the DTC codes on your vehicle. There are also versions which come with a handheld scanner. Try ebay. They are relatively inexpensive and often much cheaper than having a diagnostic done at a dealer. When you find out your code then look for a Kia forum online for help with the issue.
What problems are you having?

Posted on Feb 20, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Pontiac grand am shuts off when i stop


Is the check engine light on? Even if it is not you should have the codes read. Take it to auto parts store and get them to read the codes. It may have stored codes that will tell you what is wrong. Tell us the codes and we will try to help.

May 26, 2017 | Pontiac Cars & Trucks

1 Answer

What else could cause the check engine code to read mass airflow sensor?


OBD Codes have nothing to do with telling you the
problem or the need to replace parts

Codes are used to diagnose the system with the fault,
that set the codes

Have to component test the entire vehicle system, to find a
problem

You were only told about the code

No one can tell you what the problems may be, until the vehicle
is properly tested to even find a problem

Sep 06, 2014 | Cars & Trucks

1 Answer

No ignition reference signal


why not , tell
year car
model car
and engine type or size

then post the ACTUAL DTC error code, not the interpretation.
and symptoms.?

if you had read the FSM , all this would be moot , as it tells you this.
my wild guess, is the crank sensor is bad.
or 2nd guess. cam sensor.
or 3rd guess. is the spark read back signal is dead.

the actual code, tells you on all cars, which of the it is.

Feb 18, 2014 | Toyota Cars & Trucks

1 Answer

Check engine light on my 2007 saturn aura xr. Codes read p0011, p0016, & p0017. Just where is the crankshaft position sensor located on the 3.6 engine?


a Honda Saturn. and zero post, i wonder why.
the Saturn (and honda) FSM both tell you how to diagnose all DTCS.
why not read that.
and btw, the codes never tell you what parts is bad but rather ,they only tell you which tests fails.
the tech will test the sensor and see that its good, (say) then finds the connector bad, saving $200 in useless parts.
or more.
RTM , READ the FSM, and read what the test does.
and get the freeze frame and see what is going on.

Aug 29, 2013 | 2000 Honda CR-V

2 Answers

Why does ecm light come on?


its telling you something is wrong

Mar 01, 2011 | 2005 Chevrolet Tahoe

1 Answer

Engine code reads "700". What part is that?


i think that it is a code in the tcm otherwise transmission problem such as speed sen or input out sensors for trans or just to tell you to check transmission codes for this your scanner cant read you might have to go to dealer to read trans codes

Jan 03, 2011 | 2002 Chrysler Town & Country

1 Answer

Check engine light will not go off


You have an error code activated. You can buy a code read which will also turn off the code or take it to a repair shop that will read the code and tell you what needs to be done to fix it. Most shops charge to read the code I belive that AMMCO advertises that they will read the code for free. Most dealers will chare about $30 to $50 to read the code. Something as simple as a bad gas cap could cause the light to come on.

Aug 21, 2010 | 2002 Ford Taurus

1 Answer

Have 2 Codes PO301 and PO316. What are they and what can I do about them?


Who read your codes should have told you what they mean ,IDM codes and boost calibration high,now next time you pay autoxone to read codes dont pay them unless they tell you what they are ,Also consider yourself lucky that you can read a code ,try doing it with a europeon built car for the europeon market ,THEY ARE ALL ENCRYPTED

Jul 28, 2010 | Ford Taurus Cars & Trucks

2 Answers

Check engine light is on.


There are engine codes for alot of diffedent problems. Go to Autozone and have the code read. They will tell you what it means. Post your results, please.

Jul 20, 2008 | 1997 Honda Accord

Not finding what you are looking for?
2002 Kia Sedona Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...