Question about Peugeot 405

Open Question

Why is my 2000 Peugeot 206 making a loud creaking noise over speed bumps

This isn't a clunk or a bang - it's a definite creak/grind which only happens when driving over bumps. Loud enough for people to stop and stare!!

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: I have a creaking,clunking noise

Try looking at the sway bar link on each side. If they move easily by hand then they likely need to be replaced. You can do a sort of self test by rocking the car up and down at the front fender tire well. If you can hear it clicking when you rock it, it is likely that sway bar link. Good luck!

Posted on Sep 11, 2008

fyrebyrd1
  • 121 Answers

SOURCE: Creaking sound while turning steering wheel

There's a chance that the ball joints need grease. This should help, however once they have started to make noise like that due to lack of grease, they usually have gone bad. Replacement may be the only remedy. Hope this helps.

Posted on Nov 02, 2008

junkman1249
  • 552 Answers

SOURCE: Creaking sound while turning steering wheel

check your upper and lower control arm bushings

Posted on Dec 06, 2008

  • 1 Answer

SOURCE: LOUD CREAKING NOISE COMING FROM FRONT END

grease ball joints that should fix it

Posted on Mar 24, 2009

redbeard00
  • 957 Answers

SOURCE: Bad Creaks, Moans, and scrubbing in y truck when i go over speed bumps or turn.

You need to rent the ball-joint removal/installation tool, a ball-joint removal fork, and a foot pound torque wrench (at either Autozone or Pepboys) and you need to borrow or buy a rack 3/8",1/2" metric sockets, I think a set of E-torks, a good size hammer, a repair manual (for directions and torque specifications), and a good jack and stands.

Posted on May 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford ka creaking on drivers side when driving over bumps in road or turning


Is this a suspension creak, or a door creak?

Components which you haven't had changed are:

bottom suspension arms
Anti roll bar links

Also lubricate your door lock mechanism, hinges and window rubbers as these can cause creaks from time to time.

Nov 13, 2012 | Cars & Trucks

1 Answer

Loud creaking noise(s) from front wheels when braking.


Well if the brakes are good (I'm not convinced) I would look at some of the bushings associated with the front end (control arm, sway bar .etc)

Oct 06, 2012 | 2003 Chrysler PT Cruiser

1 Answer

Creaking and grinding noise when turning steering wheel


Were the top strut bearings changed?

You don't turn the steering wheel, unless
your have the vehicle moving or off the ground

Do you flush the power steering fluid every 3 years,
when you do the trans fluid every 3 years?

Aug 28, 2012 | 2000 Lexus Gs 300

2 Answers

I have taken my 2003 GMC Envoy in to a GM dealer more than 6 times to be repaired for a very loud creaking noise in the front end. When I brake, the creaking noise starts. Or if I go over a bump, the...


My wife drives a 2003 GMC Envoy and has been complaining about this same creaking noise upon breaking or going over speed humps. I researched this topic on the internet high and low and tried everything I read to no avail. I was about to give up and then realized it could be the motor mounts since when you break or go over bumps the engine does have some movement. Sprayed the most interesting looking motor mounts I've ever seen with silicone spray and the noise was gone! My wife has been complaining for years about this noise and now looking back what a simple solution!. By the way my motor mounts where not worn out, the rubber portion of the mount just needed a little lube.

Dec 31, 2010 | 2003 GMC Envoy Xl

1 Answer

Rear clunk in Peugeot 206, 2002


you may have a problem with a sticking handbrake
usually what happens is one of the brake shoe linings comes off and gets stuck when the car is stopping
the noise your hearing in the brake releasing

Nov 17, 2009 | 2006 Peugeot 604

1 Answer

Clunk noise from front passenger side when


That noise sounds to me like a Ball Joint problem. I would check to see if you have fittings to grease the front suspention.

Good luck, Allen

Oct 04, 2009 | 2005 Nissan Sentra

1 Answer

"Creaking noise from front right side of jeep"every time hit bump


If it is new take it back to the dealler for warranty repair. No new vehicle should have any noises . seriously, take it back for repair.

Jul 23, 2009 | 2008 Jeep Wrangler

3 Answers

Creaking sound while turning steering wheel


There's a chance that the ball joints need grease. This should help, however once they have started to make noise like that due to lack of grease, they usually have gone bad. Replacement may be the only remedy. Hope this helps.

Oct 27, 2008 | 2001 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...