Question about 1998 GMC Jimmy

Open Question

1998 gmc jimmy, changing front bumper cover, doesit clip on or are there bolts?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bryant329
  • 125 Answers

SOURCE: TPS in a 1998 GMC Jimmy

the tps is ususally at the side of the throttle body opposite where the throttle cable / tv cable mount.
sometimes it won't start, run, or run erratically. there are ways of testing this unit (by output voltage) before you commit to buying a new one. to test it you will need a dvom (digital volt ohm meter).

just a note: straight from the book... "a broken or loose tps can cause intermitten burst of fuel from the injector and an unstable idle because the ecm thinks the throttle is moving."

Posted on Sep 22, 2008

psds4
  • 293 Answers

SOURCE: 1998 GMC Jimmy Vortec V6 4.3L 4WD

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800bfc68
hope this helps

Posted on Oct 17, 2008

  • 1 Answer

SOURCE: 98 gmc jimmy front hub

1. Put the vehicle in gear, apply the parking brake and break loose the driveaxle/hub nut with a socket and large breaker bar.
2. Loosen the wheel lug nuts, raise the vehicle and support is securely on lackstands. Remove the wheel. Remove the driveaxle/hub nut.
3. Unbolt the brake caliper and hang it out of the way with wire. Remove the brake disc.
4. On models with four wheel ABS, trace the electrical lead for the wheel speed sensor along the upper control arm, then forward along the frame rail and unplug the electrical connector.
5. Remove the hub assembly-to-steering knuckle bolts. Remove the brake disc shield and wheel speed sensor assembly and set aside.
6. Tap the hub assembly from side-to-side to break it loose from the steering knuckle. Pull the hub assembly off the end of the driveaxle. Wrap the end of the driveaxle with a rag to prevent damaging it. If the hub is stuck on the splines on the end of the driveaxle, use a puller to free it.
7. Installation is reverse of removal process. Be sure to lubricate the driveaxle splines with multi-purpose grease, and tighten all of the fasteners to the proper torque.

Posted on Feb 21, 2009

  • 45 Answers

SOURCE: how do i bypass security on 98 gmc jimmy 4.3

Hi: Sounds to me like you tried to start the vehicle with something disconnected in the security system. If this is the case the solution is simple. Put key in ignition and turn to the on position, leave on for EXACTLY 30 minutes... then take key out, wait 5 minutes then start vehicle. Hope this helps... please rate suggestion... ty

Posted on May 21, 2009

  • 126 Answers

SOURCE: 1998 gmc jimmy shifts fine through 3 gears wont shift into overdrive

check transmission fluid .

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front bumper removal?


There are the Bolts that hold The Bumper to the Tie Bar, then you have the Clips that go to the Splash Guard... You will find the Bolts Easy and the CLips to be a pain.. But it is easy to remove

Apr 13, 2013 | 2005 GMC Canyon

1 Answer

Gmc jimmy bumper


zip ties and a drill, stitch it like frankenstien

Jul 08, 2012 | 1999 GMC Jimmy

1 Answer

How to remove headlamp assambly in a volvo s60 2002


Hello,

This should be fairly simple,one may have to remove the grille.

  • Remove trimmings on the front bumper cover to allow access to the bolt for removal of the front bumper. The trimming can be removed simply by prying the trimming from the center of the bumper cover using a Philips screw driver.
  • After removing the 2 bolts on the bumper cover, you may open the hood and remove the plastic fasteners on the top of the bumper.
  • To remove the plastic fastener, simply depress the center until click. Do not press too far or the fastener will be damaged.
  • Turn the Torx screw in the wheel well counter clockwise to loosen the catch plate on the bumper. Lift the bumper cover over the catch plate and push the bumper cover forward. This completes the removal of the front bumper cover.
  • To remove the headlight assembly, you will need to loosen the bolt on the retainer near the wheel well. You will then remove the 4 bolts that hold the headlight assembly.
  • There is one bolt on the side of the headlight assembly. Two bolts on top and one at the corner of the lens. They all have the same size bolt.
  • In order to remove the headlight assembly, after removing the bolts, the headlight harness needs to be removed.
  • The next step is to remove the trimming on the lens and removing the clips that hold the lens in place. There are 4 clips. One clips on each side.
  • Once the clips are removed, the lens can be pry open with screw driver. You may want to heat the edge to soften the glue or use an utility knife to scrape the edge. Be extra careful, as the glass can be very sharp if shattered. Please also wear protective gear such as safety goggle and gloves. After this, just reverse the steps to put the headlight back together.
Take care and good luck

Nov 06, 2010 | 2002 Volvo S60

1 Answer

Do I need to go to a body repair shop in order to replace a fender? I can purchase one online and wondered if I can install it?


can be done yourself , alignment on gm trucks is sometimes tricky and bolt holes may need to be reamed out to fit properly , front bumper and headlamp need to be rmoved also to replace the fender

Aug 24, 2010 | 1998 GMC Jimmy

1 Answer

Where is the engine oil drain plug on a 1998 gmc jimmy ?


i have a 96 and an 01, go under the truck from behind the drivers side front tire, the drain plug is at the back of the oil pan just behind front skid plate, the oli filter is right behind the front bumper , there is a trap door to get to the filter, but that's only for 4x4 or awd modle's, 2wd filter's are on the drivers side of the enging infront of the starter

Jun 06, 2010 | 1998 GMC Jimmy

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

2 Answers

How do you remove the front bumper cover on a 98 honda accord sedan EX


Apply the parking brake and raise the vehicle and support it securely on jackstands.

Disconnect the negative battery cable, then the positive battery cable and wait two minutes before proceeding further (make sure you have the code if you have an anti-theft radio because you will need it after disconnecting the battery).

Working under the vehicle, detach the screws securing the lower edges of the bumper cover (use a small screwdriver to pop the center button up on the plastic fasteners, but do not try to remove the center buttons. They stay in the ferrules)

Remove the bolts, screws and plastic pins on each side retaining the bumper cover to the splash shields. Remove the bolt on each side where the bumper cover attaches to the fender.

Working at the top, detach the retaining bolts (2) securing the bumper cover to the hood latch support. Remove the cover.

When you put it back, make sure the tabs along the top edge of the bumper cover fit into the corresponding clips on the body before attaching the bolts and screws. An assistant is helpful.

Hope this helps you.

Jan 05, 2010 | 1998 Honda Accord

2 Answers

1998 GMC Jimmy Passenger seat handle broke


you have to remove seat cover on back and bottom of seat . there is a long plastic clip sowed to seat covers . push in and un hook then you can pull seat cover up to see bolts. dont pull to hard or you will rip seat cover .

Apr 16, 2009 | 1998 GMC Jimmy

1 Answer

How can I change the headlights in a 1998 Honda Accord?


Its not that hard but you have to remove bumper to get to the two bottom bolts that holds the headlights. First remove grille and there are 2 10mm bolts that holt the tip of fenders they are the first bolts under the fender weld closes to the bumper cover. Then there are two bumper mounts/brackets that hold bumper to frame/radiator support. they are held by (4) 12mm bolts may need a swivel socket to get to them( easily accessed if you remove front signal lights in the bumper held by philips screws in the corners).After removing bracket bumper should come right off. Headlights are in plain clear view. (4) 10mm bolts and you are done. Re-install in the reverse. Good Luck . If I fixed ya leave me a FIX-YA comment. Contact me if you need more info

Dec 10, 2008 | 1998 Honda Accord

2 Answers

Gmc jimmy


JACK UP VEHICLE, BLOCCK OTHER WHEELS. REMOVE DIFF. COVER & PLACE VEHICLE IN N. USING A BOX. END 8MM WRENCH; ROTATE DRIVESHAFT TO YOU LOCATE CARRIER RETAINING BOLT ON RH SIDE OF CARRIER. THIS BOLT HOLDS TO RETAING PIN IN CARRIER, APROX. 1/1/4" DIA. REMOVE PIN. PUSH BOTH AXLES INWARD. LOOK INTO CENTER OF CARRIER WHERE AXLES MERGE. EACH AXLE WILL HAVE A RETAING CIRCLIP. REMOVE EACH CLIP & PULL AXLE OUT ABOUT 1 FOOT. REMOVE REAR DRIVESHAFT & SHAFT YOKE @ FORWARD PART OF DIFF. A SPECIAL PULLER IS NEEDED. NOW YOU CAN REMOVE THE 4 BOLTS HOLDING CARRIER TO DIFF HOUSING, PREY OUT CARRIER ASSEMBLY, USE CAUTION- ITS HEAVEY!!

Nov 05, 2008 | 1998 GMC Jimmy

Not finding what you are looking for?
1998 GMC Jimmy Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...