Question about 1998 Chrysler Town & Country

Open Question

How to install input speed sensor on 1998 Town and Country

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

short shadey
  • 421 Answers

SOURCE: location of the speed sensor on 1996 town & country

they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Posted on Sep 04, 2008

StormStrikes
  • 104 Answers

SOURCE: 2002 chrysler town and country wont leave limp mode

P1694 means the battery has been disconnected in the last 50 starts. It could also show up perhaps if the battery is dying or providing low voltage. It can also indicate that the computer memory was cleared in the last 50 starts. Its typically just a status indicator and I would not expect it go into limp home mode unless there is a problem with the battery and its not able to supply the necessary power to engine components.

Posted on Dec 31, 2008

chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

  • 323 Answers

SOURCE: locassion of output speed sensor on 2003 Town and Country

The input and output speed sensors look identical on the connector side. The one over the solenoid pack is the input, the one closer to the left frame rail or left front wheel is the output sensor. I hope this helps.

Posted on Apr 26, 2009

hotrodshop
  • 106 Answers

SOURCE: where is the speed sensor in town & country

There are 2 speed sensors on your vehicle, an input speed sensor and an output speed sensor. Below is a pic showing the front of your transmission. The input sensor is closest to the engine. Both sensors look the same.

003baae.gif

Posted on Jun 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a speed sensor in a 1998 town and country?


Well it would be good to have the actual trouble code or codes to advise you.
If the speed sensor in the transmission failed, the speedometer would not work, and the sensor would have nothing to do with the shift indicator.

Jan 23, 2013 | 1998 Chrysler Town & Country

1 Answer

Where is the speed sending unit located on a chrysler town and country


transaxle has two speed sensors input speed sensor located behind transaxle cooler lines the output sensor located far right transmission case driver side.

Jan 04, 2013 | 2002 Chrysler Town & Country

2 Answers

Can I replace the transmission solonoid on a 98 Town and Country Van without resetting the computer?


It depends. Are there codes in the computer now? Has it bee reset since you replaced the input speed sensor? If the codes are still in there, the transmission may still be in limp-in mode.

Your transmission is computer controlled. Trying to diagnose or repair it without the ability to interface with the computer that controls it about the same as surfing the internet with no monitor. If you push the right buttons and click your mouse just right, you might get to the page you are looking for (not likely, but possible). However, when you do get there, you still won't know it....

Feb 21, 2012 | 1998 Chrysler Town & Country

1 Answer

How locate and replace the speed sensor on 2000 town and country


Input shaft speed sensor or output shaft speed sensor?

Jul 01, 2010 | 1996 Chrysler Town & Country

1 Answer

Replace the input speed sensor on a 2001 chrysler town and country 3.8


The input speed sensor is located directly below and a little to the right of the cooler lines that are going into the transmission. IF you are standing in from of the car, remove the air breather or anything else that prevents you from getting down in on the driver side. There are two seemingly similar plugs at 9o'clock to the rear of the motor. The one closest to the motor is the input, the one further back is the out put.

It just unscrews and you screw the new on in.

Hope this helps

Nov 02, 2009 | 2001 Chrysler Town & Country

1 Answer

Where is the speed sensor in town & country 2001


There are 2 speed sensors on your vehicle, an input speed sensor and an output speed sensor. Below is a pic showing the front of your transmission. The input sensor is closest to the engine. Both sensors look the same.

003baae.gif

Jun 10, 2009 | Chrysler Town and Country Cars & Trucks

2 Answers

Trans


Check the speed sensor on the tranny cause if the speedometer is not working the tranny will not shift.The computer will not recognize that the transmission is in motion so will not shift.

May 14, 2009 | 1998 Chrysler Town & Country

1 Answer

Locassion of output speed sensor on 2003 Town and Country


The input and output speed sensors look identical on the connector side. The one over the solenoid pack is the input, the one closer to the left frame rail or left front wheel is the output sensor. I hope this helps.

Apr 26, 2009 | Chrysler Town and Country Cars & Trucks

1 Answer

Transmission


you need to have the trouble codes read go to autozone they can read them for you and write them down and report back it is most likley a speed sensor on the transmission there is two of them and they are very cheap and easy to change called input /output speed sensors
1 05014469AA Wiring Repair Package, Input Speed Sensor
1 05014471AA Wiring Repair Package, Output Speed Sensor you dont need to use the wiring harness supllied with these sensors as they are for early model vans only please rate -jeff

Aug 23, 2008 | 2001 Chrysler Town & Country

1 Answer

Location of the speed sensor on 1996 town & country


they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Jun 17, 2008 | 1996 Chrysler Town & Country

Not finding what you are looking for?
1998 Chrysler Town & Country Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...