Question about 2004 Chevrolet Malibu

Open Question

Program keyless entry for 2004 malibu classic

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75197 Answers

SOURCE: programing keyless entry

If you have an owners manual the programming instructions are in there. If no manual here they are:

1. Turn the ignition off.
2. Ground the receiver program terminal. Jump the two terminals located in the programing ground connector. (What this means in simple terms is locate the wires that run on the right side of the trunk. There is two black wires that has a plug on the end with two prongs. It is in between the antenna and tail lights.)
3. Within 2 seconds of connecting the prongs the door locks will lock. The unlock and the rear compartment lid release will produce a cycle, causing the horn to chirp. This indicates that the module is ready for reprogramming.
4. Press and hold the lock and unlock buttons at the same time until the doors lock and unlock. The rear compartment lid will release and the horn sounds to indicate that the transmitter has successfully been reprogrammed. (Hold buttons down for approximately 12 seconds)
5. Repeat the previous step for the remaining transmitters.
6. Remove the jumper at the program connector.
7. Verify the proper operation of each transmitter

Posted on Sep 30, 2008

simard2
  • 124 Answers

SOURCE: Horn alarm randomly beeps

Make sure to check all doors, the trunk latch, and the hood to ensure that they are shut. I have looked up your 2006 Chevy Malibu and there has been a lot of people complaining about the alarm system and it going off. There is a TBS (Technical Service Bulletin) out for your car. The TBS says that the Faulty Door Sensor. Take it to your local dealership and tell him what I found for you and they should get you a quote on how much it would cost to repair it.

Thank you for using Fix Ya!
Good Luck!
Any questions don't hesitate to ask me.

Don't forget to rate the overall satisfaction of this solution.

Posted on Feb 02, 2009

  • 206 Answers

SOURCE: program a keyless enrty remote start 2004 chevy malibu

Dealer only If you find a different means let me know

Posted on Apr 08, 2009

  • 462 Answers

SOURCE: oil filter location 2004 Chevrolet Malibu Classic

Standing at the front of the car looking at the intake manifold, its on the right hand side of the manifold about 6 inches down from the valve cover under a black cap with a 32mm top on it.

Posted on Jan 04, 2010

  • 181 Answers

SOURCE: 2008 chevy malibu. how to program keyless entry remote

You must take it to the Chevy dealer.

Posted on Mar 09, 2010

Testimonial: "thank you"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way to reset keyless entry for 04 endeavor?


Search Results

    2004 Mitsubishi Endeavor Key Fob Remote Programming ...

    blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
    Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

    Mitsubishi - Free Keyless Remote Fob Entry programming .

    How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

    ? 2:04
    www.youtube.com/watch?v=yeQRdre7O0Q
    Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
    ... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

Nov 01, 2015 | Cars & Trucks

1 Answer

How do I program my keyless entry to my 2004 Chevy Malibu Lt


take it to your dealer if you dont have another one

Jul 18, 2015 | Cars & Trucks

1 Answer

How do u find out if a 2004 chevy Malibu is equipped with keyless entry


Take you VIN to your local GM dealer and ask them. If it is they can pull the codes and get you a new keyless fob. But they arent cheap... Expect to pay around $200

Jan 24, 2012 | 2004 Chevrolet Malibu

1 Answer

How to program a keyless entry for land rover


MOST OF THE TIME WHEN YOU HAVE PROBLEMS IN THE REMOTE AND KEYLESS ENTRY.THE DEALERSHIP HAS TO REPROGRAM IT.BUT FIRST CHECK ALL THE FUSES AND RELAYS.IF THEY ARE OKAY.THEN DEALERSHIP HAS TO FIX.

Sep 16, 2009 | 2004 Land Rover Discovery

1 Answer

How do i reset the the keypad for the keyless entry on the door


how to program keyless remote on chevy malibu 2004

Jun 18, 2009 | 2002 Ford Explorer

2 Answers

How do u program a new key fob for a 2004 chevy Malibu


Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation

Jun 04, 2009 | 2004 Chevrolet Malibu

1 Answer

Program a keyless enrty remote start 2004 chevy malibu


Dealer only If you find a different means let me know

Apr 07, 2009 | 2004 Chevrolet Malibu

2 Answers

My remote for the keyless entry does not work.


does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back

Mar 22, 2009 | 2004 Lincoln LS

Not finding what you are looking for?
2004 Chevrolet Malibu Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...