Question about Mitsubishi Galant

Open Question

How to bleed power steering pump on 1997 galant

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11 Answers

SOURCE: 2004 Galant Power Steering?

is the fluid circulating well , you could see it through the power steering fuel level after removing the rod , if not then you got proplems with the pump ,if the fluid is circulating the the rack and union pistons may have ruined

Posted on Oct 31, 2008

  • 2 Answers

SOURCE: power steering pump

The pump has to be removed from under the vehicle by removing the exhaust system from the flex bracket and moving it to as far left of the vehicle as possible..remember you have to remove the splash shield that protects the engine components first...then remove all associated bolts,hoses (plug them so they won't drip) and remove the pump from the vehicle..that it.

Posted on Dec 31, 2008

RudolfDiesel
  • 100 Answers

SOURCE: 92 dodge p u cummins eng power steering pump

to bleed the system fill the fuel filter then crack the inlet fule line turn over untill you get fuel then tightnline and start

Posted on Jan 11, 2009

germcelchar
  • 389 Answers

SOURCE: how do i bleed my power steering rack on subaru legacy rs turbo

A power steering dosent need bleeding. If you replaced it a week ago and was fine until now then it's not an air problem. Power steering fluid is pumped through the system even when the steering is not being used. Definatly not an airlock problem. Cheer's

Posted on Oct 16, 2009

CaptainKeyz
  • 202 Answers

SOURCE: remove a power steering pump out of a 97 chevy suburban

For step by step instruction, you best pick up the auto repair guide.
Steering pumps, in general, are not very difficult to replace. Pay careful attention to how you take it apart. Use a camera to help you remember how things go.
You will need to remove the drive belt...it rotates all the accessory pulleys, including the steering pump.
The pump should only have two or three bolts holding it on. Make sure you have a hose clamp, or something clean, to catch the steering fluid when you remove the hose.
Make sure not to over or under tighten the hose clamps when reinstalling it. Start snug...then check for leaks, and tighten if needed.
Good Luck.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the poer steering pump


Hi Amanda,here's a link showing how to replace your power steering pump,here's another link on bleeding the system.Got me a 85 Nissan 720 4x4,it's silver,here's a video of it.

Nov 27, 2013 | 1997 Nissan Pickup

1 Answer

How does one replace an alternator belt on a 97 mitsubishi galant?


Place a small charge in the compartment and blow it up

Dec 28, 2012 | 1997 Mitsubishi Galant

1 Answer

1997 Jeep grand Cherokee limited 5.2l v8....how to fix very stiff steering. I have changed the power steering pump already an it is still hard to turn my wheels


sound like lack of lubrication at the steering joints, your ball joints need greasing and make sure you bleed power steering system, check power steering fluid level.if low more like power steering system full of air need bleeding.

Jan 25, 2012 | 1997 Jeep Grand Cherokee

1 Answer

1995 Mitsubishi Galant: Replaced the pressure lines and power steering pump. Still groaning at pump and air in lines. How do I bleed it all out?


You've already aireated it , so you will have to let it set. to purge the air you have to turn the steering 10 to 20 times all the way left and right. Lift the front tires this will make it easier

Feb 11, 2011 | Mitsubishi Galant Cars & Trucks

2 Answers

Im about to change the power steering pump and i was wondering the best way to bleed it when im done. I have a 2003 mitsubishi galant


hi, this one is easy, fill to level turn steering from left to right, for about 5 times each and if working a noise will be heard. recheck level. reson for turning the steering wheel it forces air out of system. gerry

Sep 11, 2010 | 2003 Mitsubishi Galant

1 Answer

Replace power steering pump.


  1. Disconnect the negative battery cable.
  2. If necessary, remove the air cleaner duct and the air cleaner.
  3. Remove the drive belt from the air conditioning compressor, if equipped.
  4. Loosen power steering pump belt adjustment as follows:
    1. Loosen the pivot and mounting bolts.
    2. Loosen the idler pulley locknut and turn the adjusting nut counterclockwise to remove the power steering belt.
  5. Loosen the power steering hoses at the pump and remove the bolts holding the power steering pump to the bracket.
  6. Disconnect and plug the power steering hoses and remove the pump from the vehicle.
To install:
  1. Using new O-rings, connect the power steering hoses to the steering pump.
  2. Install the power steering pump and secure it with its mounting bolts. Tighten the front and rear mounting bolts to specifications.
  3. Install the remaining components in the reverse order from which they were removed.
  4. Connect the negative battery cable.
  5. Fill the power steering system, start the engine and turn the steering wheel from side-to-side to bleed air from system

Feb 14, 2010 | 1997 Nissan Maxima

3 Answers

How do i bleed my power steering rack on subaru legacy rs turbo


if its been a week, there should no tbe any air. if its heavy, the rack could be bad, or weak pump????? any noises? air will usually cause a whiney noise, and there will be air whipped, foamy fluid in the pump. A pump pressure regulator could be stuck open, not allowing full pressure? I would have a shop diagnose it, tell them the history and see if they can find a cause.

Oct 16, 2009 | 1997 Subaru Legacy

2 Answers

My 2001 mitsubishi Gallant power steering went off while driving


Check the power steering pump. Make sure that it is working correctly. You can have it checked at autozone or kragen . That is most likely your problem is that the power steering pump has gone bad

Jun 01, 2009 | 2001 Mitsubishi Galant

1 Answer

2004 Galant Power Steering?


is the fluid circulating well , you could see it through the power steering fuel level after removing the rod , if not then you got proplems with the pump ,if the fluid is circulating the the rack and union pistons may have ruined

Oct 30, 2008 | 2004 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...