Question about 1985 Nissan Pickup

1 Answer

Timing My truck runs but it lacks power(2.4 engine). I pulled the valve cover off and the silver link on the timing chain is off 4 links from the #2 hole on the camshaft sprocket. The timing chain was just changed a couple of years ago. There is also a noise coming from the front of the motor(knocking noise). I'm thinking about pulling the sprocket off and lining it back up. What do you think I should do? Thanks.

Posted by on

  • Fred Kenmuir May 11, 2010

    have you tried adjusting the timing before you checked it? How much slac is in the chain now that you have it exposed? Can you see any signs of broken teeth on any of the timing gears? Or has the key way sheared off? Because if the chain was done a couple of years ago it should not be needing to be re-done allready.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 44,283 Answers

Bet the workshop manual as sometimes you have to turn the engine over twice to get the marks to line up
if it was off 4 links , it probably would not start and if it did would be all over the place

Posted on Jul 30, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
SUL827
  • 93 Answers

SOURCE: 2002 nissan maxima gle timing chain or sprockets

Ok, first off you need to take your vehicle to a Nissan dealer for a second opinion. Its not at all common to need a T-chain @ 58,000 miles unless you dont take care of your car and or you beating the snot out of it like it was stolen. What is the symptom? What caused it? When did it start? Second, this is not something an amature could/should do as it is very involved and there are alot of things you could potentially mess up. Third a new engine(long block), parts alone would run approx. 6-8 thousand dollars. A used engine could be an option and could run approx.1500-2500 dollars depending on mileage. Hope this helps and good luck.

Posted on Sep 16, 2008

Lady_Chaos
  • 21 Answers

SOURCE: driving home my truck quit running

well you didn't specify the year, make, and model of the truck you are asking about so this is the best answer I can come up with. Below is a list I found that says what vehicles are interference motors...

INTERFERENCE ENGINES WITH TIMING BELTS
ACURA
engine_interference.jpg
1986-89 1.6L Integra
1991-95 1.7L Integra
1990-95 1.8L Integra
1986-89 2.5L Legend
1992-94 2.5L Vigor
1986-89 2.7L Legend
1990 2.7L Legend
1991-95 3.0L NSX
1991-95 3.2L Legend
AUDI
1970-93 All Except 1970-77
1.9L & 1970-73 1.8L
BMW
1987-95 2.5L 325I 525I
1994-95 4.0L 740I
CHRYSLER
1993-95 1.5L Colt
1987-88 1.5L Colt
1992-95 1.5L Eagle Summit
1987-88 1.6L Colt
1989-92 1.6L Eagle Summit
1994-98 2.0L Neon Stratus
1990-95 2.0L Eagle Talon
DAIHATSU
1988-92 1.0L Charade
1988-92 1.3L Charade
1990-92 1.6L Rocky
FIAT
1974-79 1.3L 128 Series
1979-82 1.5L Stranda
1974-78 1.6L 124 Series
1974-78 1.8L 124 Series
1974-78 1.8L 131 Series, Brava
1979-82 2.0L Brava, Spider
FORD
1981-85 1.6L Escort, EXP
1981-83 1.6L LN7, Lynx
1984-85 2.0L Escort, Tempo
1993-95 2.0L Probe
1986-88 2.0L Ranger
1984-87 2.0L Lynx, Topaz Diesel
1985 2.2L Ranger
1989-92 2.2L Probe
1986-88 2.3L Ranger
1986-87 2.3L Diesel Ranger
1991-98 4.6L Crown Victoria
GM
1986-95 1.0L Geo Metro
1989-91 1.0L Firefly (CANADA)
1985-88 1.5L Sunburst (CANADA)
1985-89 1.5L Spectrum
1990-93 1.6L Prizm, Storm
1981-84 1.8L Diesel (CANADA)
1982-86 1.8L Buick Skyhawk
1990-98 1.9L Saturn
1987-88 2.0L Buick Skyhawk
1988-95 2.3L Quad Four
1985-87 3.0L Buick
1979-95 3.8L Buick
HONDA
1986-87 1.0L Prelude
1973-78 1.2L All
1973-78 1.3L All
1980-84 1.3L All
1973-78 1.5L All
1985-89 1.5L Civic
1988-95 1.5L Civic, CRX
1993-95 1.5L Civic Del Sol
1979-84 1.5L All
1985-87 1.5L CRX
1993-95 1.6L Civic Del Sol
1973-78 1.6L All
1980-82 1.6L All
1988-95 1.6L Civic, CRX
1984-87 1.8L Prelude, Accord
1979-83 1.8L All
1986-91 2.0L Prelude
1990-91 2.1L Prelude
1990-95 2.2L Prelude, Accord
1992-95 2.2L Prelude
1995 2.7L Accord
HYUNDAI
1984-95 1.5L Excel Scoupe
1995-98 1.5L Accent
1992-95 1.6L Elantra
1993-95 1.8L Elantra
1992-95 2.0L Sonata
1989-91 2.4L Sonata
1990-95 3.0L Sonata
INFINITI
1990-92 3.0L M30
ISUZU
1987-89 1.5L I-Mark
1990-93 1.6L Stylus Impulse
1987-89 2.0L Impulse
1981-87 2.2L Diesel Truck
1986-95 2.3L Truck Trooper
1988-95 2.6L Truck Rodeo Amigo
1991-96 3.2L Trooper Rodeo Amigo
KIA
1995 2.0L Sportage
MAZDA
1984-85 2.0L 626
1988-92 2.2L 626 MX6
1989-93 2.2L Pickup
1988-95 3.0L 929 MPV
MITSUBISHI
1985-95 1.5L Mirage Precise
1990-92 1.6L Mirage
1989-95 2.0L Galant Eclipse
1983-86 2.3L Diesel Pickup
1994-95 2.4L Galant
NISSAN
1982 1.5L Centra
1983-88 1.6L Sentra Pulsar
1987-89 1.8L Pulsar
1982-89 2.0L Stanza 300ZX
1984-95 3.0L Maxima 300ZX Pathfinder
PORSCHE
1976-83 2.0L 924
1976-89 2.5L 944 Series
1989 2.7L 944 Series
1989-91 3.0L 944 Series
1976-83 4.5L 928
1984 4.7L 928
1985-91 5.0L 928
1992-95 5.4L 928
SUZUKI
1985-94 1.3L Samurai Sidekick
1989-94 1.3L Swift
TOYOTA
1986-95 1.5L Tercel
1981-83 2.2L Pickup
1984-87 2.4L Pickup
1982-88 2.8L Celica Cressida
1987-94 3.0L 4-Runner
VOLKSWAGEN
1976-91 All Except 1.9 2.1L Engine
1990-92 1.6L Golf (CANADA) Jetta
1990-95 2.0L GTI Jetta GLI Passat
VOLVO
1991 2.3L Coupe 940
1986-94 2.3L 240 740 940

Posted on Jan 30, 2009

  • 383 Answers

SOURCE: 93 Nissan Pickup 2400/12 valve

I would venture to guess that a timing chain guide broke and the chain chewed a hole thought the timing cover. The timing cover also has coolant passing through it where the water pump is attached. If you were running a multi viscosity oil, even it it were a 20-40 and got surprised by a zero degree day, I doubt seriously, it would cause that to occur. That series engine had problem s with timing chain guide failures. However, there usually is some chain rattle well before a disastrous failure. Most of my customers noticed the chain noise before it has caused catastrophic damage.
Sorry you have suffered such a loss. Good luck on your repair. A used timing cover would be the cheapest route. A place in Dallas called Bishops, buys engine cores, dismantles them, evaluates them, cleans the good parts up and sells them at very reasonable prices. They ship all over the country.

Posted on Mar 25, 2009

junmag
  • 175 Answers

SOURCE: cam timing with no colored links on chain!!

buy a new chain to make things easier

Posted on Jun 02, 2009

polarcycle
  • 1392 Answers

SOURCE: How to reinstall factory timing

103196368 Hopefully this will help. This is for the 1.8l if you need the 2.5, I may be able to help.

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

2 Answers

My timing chain tensioner on my 01 dodge stratus wore out and chain slipped a few links is there any way to get chain,aligned with cams and crank without removing timing chain cover it is a 2.7 litre dohc


No-have to remove the front cover

Watch the Video on you tube

Has the oil seldom been changed on
that motor since it was new?

Lots to read on problems with that motor

Lack of oil changes
Sludge & Coolant Leaks
Water Pump & Chain issues

Seems most chrysler engines have problems
especially 4 cylinders

Aug 15, 2014 | Cars & Trucks

1 Answer

2003 Pontiac Sunfire 2.2 OHC rotates but won't


TDC is after the number one piston comes up on the compression stroke. So if you take the valve cover off, you should be able to watch the intake valve and tell where the cam timing is as the piston comes up. Keep in mind if cam timing is off you won't have much if any compression on most cylinders.

Aug 11, 2013 | Cars & Trucks

1 Answer

Need diagram how to install timing chain 2004 Malibu overhead cam


Procedure is pasted below. Please let me know if you have questions.
Removal & Installation2.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    NOTE The timing chain has 2 matching colored links and 1 uniquely colored link.
    Negative battery cable, PCV hose, Fuel line bracket, Ignition coil and module assembly Ground strap from camshaft cover, Camshaft cover, Front fender liner, Accessory drive belt Crankshaft balancer pulley, Accessory drive belt tensioner, Front cover-to-water pump bolt Remaining front cover bolts, Front cover
  5. Rotate the engine until the crankshaft sprocket mark aligns with the matching colored link (2) at the 5 o-clock position.
  6. Confirm that the INT diamond on the intake camshaft sprocket is aligned with the uniquely colored link at (1) the 2 o-clock position.
  7. Confirm that the EXH triangle on the exhaust camshaft sprocket is aligned with the matching colored link (3).
  8. Remove or disconnect the following:
    NOTE Use a 24 mm wrench to hold the camshafts to prevent them from turning.
    Timing chain tensioner, Fixed timing chain guide access plug, Fixed timing chain guide Upper timing chain guide, Exhaust camshaft sprocket, Timing chain tensioner guide Intake camshaft sprocket, Timing chain through the top of the cylinder head Crankshaft sprocket

    jturcotte_638.jpg

    Fig. Lining up the crankshaft sprocket mark with the colored link in the 5 o-clock position (2).


    jturcotte_639.jpg

    Fig. Aligning the intake camshaft sprocket mark with the colored link in the 2 o-clock position (1).


    jturcotte_640.jpg

    Fig. Aligning the exhaust camshaft sprocket (3).

To install:
  1. Install the crankshaft sprocket with the timing mark in the 5 o-clock position.
  2. Assemble the intake camshaft sprocket to the timing chain with the timing mark lined up with the uniquely colored link (1). Hand tighten a new intake camshaft sprocket bolt.
  3. Lower the timing chain through the opening in the cylinder head.
  4. Route the timing chain around the crankshaft sprocket and line up the first marching colored link (2) with the timing mark on the crankshaft sprocket.
  5. Install the exhaust camshaft sprocket with a new bolt loosely onto the exhaust camshaft.
  6. Align the timing mark on the sprocket with the last matching colored (3).
  7. If necessary, align the camshaft as follows:
    1. Using a 24 mm wrench, first turn the intake camshaft until the alignment feature on the back of the camshaft sprocket seats in the notch in the front of the intake camshaft.
    2. Turn the crankshaft 45 degrees in either direction.
    3. Turn the intake camshaft to the appropriate location.
    4. Turn the crankshaft back to top dead center (TDC).
  8. When the sprocket seats in on the camshaft, tighten the sprocket bolt hand tight.
  9. Verify all of the colored links and the appropriate timing marks are still aligned.
  10. Install the fixed timing chain guide. Tighten the bolts to 133 inch lbs. (15 Nm).
  11. Install the upper timing chain guide. Tighten the bolts to 89 inch lbs. (10 Nm).
  12. Using a 24 mm wrench to hold the camshafts, tighten the camshaft sprocket bolts 63 ft. lbs. (85 Nm) plus 30 degrees.
  13. Measure the timing chain tensioner from end to end. A new tensioner should be supplied in the fully compressed non-active state. A tensioner in the compressed state will measure 2.83 inches (72 mm) front end to end. A tensioner in the active state will measure 3.35 inches (85 mm) from end to end.
  14. If the timing chain tensioner is not in the compressed state, perform the following steps:
    1. Remove the piston assembly from the body of the timing chain tensioner by pulling it out.
    2. Install the bottom half of the Tensioner tool J-45027-2 into a vise.
    3. Install the notch end of the piston assembly into the bottom half of the tensioner tool.
    4. Using the top half of the Tensioner tool J-45027-1, turn the ratchet cylinder into the piston.
    5. Install the compressed piston assembly back into the timing chain tensioner body until it stops at the bottom of the bore. Do not compress the piston assembly against the bottom of the bore.

  15. Install the timing chain tensioner assembly. Tighten to 66 ft. lbs. (75 Nm).
  16. Release the timing chain tensioner by compressing it approximately 0.08 inches (2mm). Feed a rubber-tipped tool down through the cam drive chest to reset on the cam chain. Give the tool a sharp jolt diagonally downwards to release the tensioner.
  17. Install the timing chain oiling nozzle.
  18. Install the timing chain guide bolt access hold plug with silicone sealant on the threads. Tighten the plug to 59 ft. lbs. (90 Nm).
  19. Install or connect the following:

    Camshaft cover. Tighten the bolts to 89 inch lbs. (10 Nm). Front cover with new gasket. Tighten the bolts to 18 ft. lbs. (25 Nm). Accessory drive belt tensioner. Tighten the bolts to 33 ft. lbs. (45 Nm). Crankshaft balancer pulley using a new bolt. Tighten the bolt to 74 ft. lbs. (100 Nm) plus 75 degrees. Accessory drive belt, Front fender liner, Ground strap to camshaft cover Ignition coil and module assembly, Fuel line bracket, Air intake assembly, Negative battery cable
  20. Refill the cooling system to the correct level.
  21. Refill the engine with oil to the correct level.
  22. Start the engine and check for leaks.

    jturcotte_2381.gif

    Fig. Compressing the timing chain tensioner-2.2L engine.

Oct 06, 2011 | 2004 Chevrolet Malibu

1 Answer

I replaced the right side head on my 2001 mustang gt and i need to know how to set up the timming so it will run right


Hi, this engine user copper links on the chain align the copper links with the marks shown on the diagram below. Please let me know if you have more questions, and thanks for using FixYa.

To install:
  1. Compress the timing chain tensioner plunger in a soft jaw vise and install a retaining clip to hold the plunger in place.
  2. Remove the tensioner.
  3. If the copper links are not visible on the timing chains, mark one link on each end of the chain.
  4. Install the left and right timing chain guides and tighten the bolts to 89 inch lbs. (10 Nm).
  5. Position the lower end of the left timing chain on the crankshaft sprocket, aligning the copper link with the timing mark on the outer flange of the crankshaft sprocket.
  6. Position the timing chain on the left camshaft sprocket with the camshaft sprocket timing mark aligned with the copper link.
  7. Position the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
  8. Remove the retaining clip from the tensioner plunger.
  9. Position the lower end of the right timing chain on the crankshaft sprocket, aligning the copper link with the timing mark on the outer flange of the crankshaft sprocket.
  10. Position the timing chain on the right camshaft sprocket with the camshaft sprocket timing mark aligned with the copper link.
  11. Position the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
  12. Remove the retaining clip from the tensioner plunger.
  13. Ensure correct alignment of all timing chain links and sprocket timing marks.
  14. Install the camshaft roller followers and tighten the camshaft sprocket bolts. See the procedure under Camshaft.
  15. Install the crankshaft sensor ring on the crankshaft.
    jturcotte_2085.gif

    Fig. Timing chain link and sprocket timing mark alignment-4.6L engine

  16. Apply sealant to the front cover mating surface as shown.
    jturcotte_2086.gif

    Fig. Sealant application to the front cover mating surface-4.6L engine

  17. Install a new gasket on the front cover, then install the front cover and hand tighten the bolts.
  18. Tighten the front cover bolts in the sequence shown to 18 ft. lbs. (25 Nm).
  19. Tighten the front cover-to-oil pan bolts in the sequence shown to 15 ft. lbs. (20 Nm), plus an additional 60 degrees
    jturcotte_2087.gif

    Fig. Front cover bolt tightening sequence-4.6L engine

    jturcotte_2088.gif

    Fig. Front cover-to-oil pan bolt tightening sequence-4.6L engine

  20. Lubricate the engine front cover and oil seal lip with clean engine oil and install the seal using a seal installer.
  21. Apply sealant to the Woodruff key slot in the crankshaft pulley, then press on the crankshaft damper.
  22. Tighten the crankshaft damper as follows:
    1. Step 1: 66 ft. lbs. (90 Nm).
    2. Step 2: Loosen the bolt one full turn.
    3. Step 3: 37 ft. lbs. (50 Nm).
    4. Step 4: 90 degrees.

  23. Connect the crankshaft position sensor connector.
  24. Install the power steering pump and tighten the bolts to 18 ft. lbs. (25 Nm).
  25. Install the wiring harness retainer to the power steering stud bolt.
  26. Install the power steering pump pulley shield.
  27. Install the water pump pulley.
  28. Install the J bracket to the engine front cover stud bolt.
  29. Install both left and right camshaft position sensor connectors.
  30. Install both left and right radio interference capacitors.
  31. Connect the hoses from the coolant crossover.
  32. Install the valve covers. See the procedure under Cylinder Head.
  33. Install the right side idler pulley.
  34. Install the accessory drive belt.
  35. Install the coolant degas bottle.
  36. Connect the negative battery cable.
  37. Fill the crankcase with clean engine oil.
  38. Start the engine. Check for leaks and proper operation.

Aug 14, 2011 | Ford Mustang Cars & Trucks

1 Answer

How do you remove toyota timeing chain


Timing Chain and Gears Removal & Installation To Remove:
toy_car_18_gen-p-s-mnts-cvrs-exhst_xp.gif

Except XRS toy_car_18_eng_cmpnts+oil_pmp_loc_1zz-fe_xp.gif

XRS toy_car_18_eng_cmpnts+oil_pmp_loc_2zz-ge_xp.gif

toy_car_18_gen-p-s-mnts-cvrs-exhst_xp.gif

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain cooling system.
  3. Remove the upper front fender apron insulator.
  4. Remove the upper radiator support insulator.
  5. Remove the right front wheel and tire assembly.
  6. Remove the right lower splash shield.
  7. Remove the drive belt and alternator.
  8. Remove the air switching valve (XRS)
  9. Remove the power steering oil pressure switch connector.
  10. Remove the 2 power steering mounting nuts and through bolts. Remove the steering pump from the engine. Secure the steering pump to the cowl toy_car_15_wood_block_on_jack.gif

  11. Raise and support the engine with floor a jack. toy_car_18_eng_rh_mntng_inslt_blts.gif

  12. Remove the right engine mount. toy_car_18_eng_cylndr_hd_cvr_blts.gif

  13. Remove the 2 nuts, 2 clips and the cylinder head shield (except XRS).
  14. Remove the 4 ignition coils.
  15. Remove the 2 ventilation hoses from the cylinder head valve cover.
  16. Remove the 9 bolts, 2 seal washers, 2 nuts, cylinder head cover and gasket (except XRS). XRS toy_car_18_eng_cylndr_hd_cvr_blts_2zz-g.gif

  17. Remove the 4 bolts and the cylinder head shield (XRS).
  18. Remove the 2 nuts, bolt and remove the ventilation hose from the ventilation pipe (XRS). XRS toy_car_18_eng_cylndr_hd_cvr_ventl_hs-pp.gif

  19. Remove the Ventilation pipe and gasket (XRS).
  20. Remove the 9 bolts, wire harness protector. Remove the cylinder head cover and gasket (XRS).
  21. Remove the O-ring from the cylinder head cover (XRS)
  22. Turn the crankshaft pulley and align its groove with timing mark "0" on the timing chain cover. toy_car_18_eng_tmng_mark.gif

  23. Ensure that the marks on the camshaft timing sprockets are in straight line on the timing chain cover surface as shown. toy_car_18_eng_tmng_point_marks.gif

  24. If not turn the crankshaft 1 revolution (360°) and align the marks as above.
  25. Remove the crankshaft pulley toy_car_18_eng_rmv_crnk_sft_pos_snsr_blts.gif

  26. Remove the 2 mounting bolts and remove the crankshaft position sensor.
  27. Remove the mounting bolt, nut and the drive belt tensioner.
  28. Remove the right engine mount bracket.
  29. Remove the front exhaust pipe (XRS).
  30. Remove the Exhaust manifold brace (XRS).
  31. Remove the Exhaust manifold (XRS) toy_car_18_eng_tmng_chn_tnsnr_blts.gif

  32. Remove the 2 mounting nuts and remove the chain tensioner.
  33. Remove the water pump. Except XRS toy_car_18_eng_tmng_chn_cvr_blts_1zz-fe.gif

    XRS toy_car_18_eng_tmng_chn_cvr_blts_2zz-ge.gif

  34. Remove the 11 mounting bolts and nut (except XRS).
  35. Remove the 12 bolts (XRS).
  36. Remove the stud bolt.
  37. Remove the timing chain cover and 2 gaskets.
  38. Remove the crank sensor plate.
  39. Remove the timing chain tensioner slipper mounting bolt. Remove the tensioner slipper. toy_car_18_eng_tmng_chn_sprkt.gif

    Note: If the crankshaft timing sprocket cannot be removed by hand, use 2 screwdrivers. Position shop rags as shown to prevent damage.
  40. Remove the timing chain and crankshaft timing sprocket.
  41. Remove the 2 chain vibration damper mounting bolts. Remove the vibration damper toy_car_18_eng_tmng_cntrl_assy.gif

  42. Hold the camshaft hexagonal section with a wrench. Remove the sprocket mounting bolt.
  43. Remove the valve timing controller assembly and timing sprocket.
Note: Be careful not to damage the cylinder head and valve lifter with the wrench.
Do not disassemble the valve timing controller assembly.

Oct 19, 2010 | 2005 Toyota Corolla

1 Answer

Heavy ticking from top of motor on 1998 sl2. Thinking it's the timing chain at first but it is really sounding heavy on top of valve cover. Is it timing chain or valves. If valves what is likely cause....


Check your oil first. I guarantee your car burns oil and it may be very low on low. The ticking may be a lifter starved for oil or one that has debris in or on it. The timing chain usually makes a "slapping" sound when it gets slack in it from lack of tensioner adjustment.

A sure fire way to check the timing chain if you are concerned is to take off the valve cover (also a good time to replace the valve cover gasket). Then you can see the chain and feel and see if there is any slack in it.

Dec 31, 2009 | 1993 Saturn SL2

2 Answers

Timing on 4.7 help


INSTALLATION
  1. Using a vise, lightly compress the secondary chain tensioner piston until the piston step is flush with the tensioner body. Using a pin or suitable tool, release ratchet pawl by pulling pawl back against spring force through access hole on side of tensioner. While continuing to hold pawl back, Push ratchet device to approximately 2 mm from the tensioner body. Install Special Tool 8514 lock pin into hole on front of tensioner. Slowly open vise to transfer piston spring force to lock pin (Resetting Secondary Chain Tensioners).
  2. Position primary chain tensioner over oil pump and insert bolts into lower two holes on tensioner bracket. Tighten bolts to 28 N·m (250 in. lbs.). CAUTION: Overtightening the tensioner arm torx® bolt can cause severe damage to the cylinder head. Tighten torx® bolt to specified torque only.
  3. Install right side chain tensioner arm. Apply Mopar® Lock N, Seal to torx® bolt, tighten bolt to 17 N·m (150 in. lbs.). NOTE: The silver bolts retain the guides to the cylinder heads and the black bolts retain the guides to the engine block.
  4. Install the left side chain guide. Tighten the bolts to 28 N·m (250 in. lbs.). CAUTION: Overtightening the tensioner arm torx® bolt can cause severe damage to the cylinder head. Tighten torx® bolt to specified torque only.
  5. Install left side chain tensioner arm. Apply Mopar® Lock N, Seal to torx® bolt, tighten bolt to 17 N·m (150 in. lbs.).
  6. Install the right side chain guide. Tighten the bolts to 28 N·m (250 in. lbs.).
  7. Install both secondary chains onto the idler sprocket. Align two plated links on the secondary chains to be visible through the two lower openings on the idler sprocket (4 o'clock and 8 o'clock). Once the secondary timing chains are installed, position special tool 8515 to hold chains in place for installation (Installing Secondary Timing Chains on Idler Sprocket).
  8. Align primary chain double plated links with the timing mark at 12 o'clock on the idler sprocket. Align the primary chain single plated link with the timing mark at 6 o'clock on the crankshaft sprocket (Timing Chain System).
  9. Lubricate idler shaft and bushings with clean engine oil.
  10. Install all chains, crankshaft sprocket, and idler sprocket as an assembly (Installing Idler Gear, Primary and Secondary Timing Chains). After guiding both secondary chains through the block and cylinder head openings, affix chains with a elastic strap or the equivalent, This will maintain tension on chains to aid in installation. NOTE: It will be necessary to slightly rotate camshafts for sprocket installation.
  11. Align left camshaft sprocket “L” dot to plated link on chain.
  12. Align right camshaft sprocket “R” dot to plated link on chain. CAUTION: Remove excess oil from the camshaft sprocket bolt. Failure to do so can result in over-torque of bolt resulting in bolt failure.
  13. Remove Special Tool 8515, then attach both sprockets to camshafts. Remove excess oil from bolts, then Install sprocket bolts, but do not tighten at this time.
  14. Verify that all plated links are aligned with the marks on all sprockets and the “V8” marks on camshaft sprockets are at the 12 o'clock position (Timing Chain System). CAUTION: Ensure the plate between the left secondary chain tensioner and block is correctly installed.
  15. Install both secondary chain tensioners. Tighten bolts to 28 N·m (250 in. lbs.). NOTE: Left and right secondary chain tensioners are not common.
  16. Before installing idler sprocket bolt, lubricate washer with oil, and tighten idler sprocket assembly retaining bolt to 34 N·m (25 ft. lbs.).
  17. Remove all locking pins (3) from tensioners. CAUTION: After pulling locking pins out of each tensioner, DO NOT manually extend the tensioner(s) ratchet. Doing so will over tension the chains, resulting in noise and/or high timing chain loads.
  18. Using Special Tool 6958, Spanner with Adaptor Pins 8346, tighten left (Tightening Left Side Camshaft Sprocket Bolt) and right (Tightening Right Side Camshaft Sprocket Bolt). camshaft sprocket bolts to 122 N·m (90 ft. lbs.).
  19. Rotate engine two full revolutions. Verify timing marks are at the follow locations:
  20. Lubricate all three chains with engine oil.
  21. After installing all chains, it is recommended that the idler gear end play be checked (Measuring Idler Gear End Play). The end play must be within 0.10–0.25 mm (0.004–0.010 in.). If not within specification, the idler gear must be replaced.
  22. Install timing chain cover (Refer to 9 - ENGINE/VALVE TIMING/TIMING BELT / CHAIN COVER(S) - INSTALLATION) and crankshaft damper (Refer to 9 - ENGINE/ENGINE BLOCK/VIBRATION DAMPER - INSTALLATION).
  23. Install cylinder head covers (Refer to 9 - ENGINE/CYLINDER HEAD/CYLINDER HEAD COVER(S) - INSTALLATION). NOTE: Before installing threaded plug in right cylinder head, the plug must be coated with sealant to prevent leaks.
  24. Coat the large threaded access plug with Mopar® Thread Sealant with Teflon, then install into the right cylinder head and tighten to 81 N·m (60 ft. lbs.) (Cylinder Head Access Plug Location).
  25. Install the oil fill housing.
  26. Install access plug in left cylinder head (Cylinder Head Access Plug Location).
  27. Install power steering pump (Refer to 19 - STEERING/PUMP - INSTALLATION).
  28. Install radiator fan shroud.
  29. Fill cooling system (Refer to 7 - COOLING - STANDARD PROCEDURE).
  30. Connect negative cable to battery.

Jul 08, 2009 | 2000 Dodge Durango

1 Answer

Timing chain


If it has not broken or jumped timing you simply remove the valve cover and timing chain tennsioner. Then cut a link out of the old chain on top of the cam gear, then you attach the new chain with the supplied master link and slowly rotate the engine until the old chain has run out and the new chain is in it's place. It's best to have a helper to rotate so you can hold the chain against the cam gear. Once this is done recheck the can timing and do not let the chain slip or you will have to pull the injection pump and retime it. Even if you do it's easier than removing the front cover! Good luck!

Dec 21, 2008 | 1986 Mercedes-Benz 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...