Question about Buick LaCrosse

Open Question

How to change rear brakes on a 2006 buick lacrosse

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 57 Answers

SOURCE: How To Change Rear Brake Pads on Audi A6 2006

Remove the tires, Remove the calaper bolts, (small heads on them 12mm or so) Remove calaper, Pads are setting in a holder. Lube new pads with litheum grease and place in holder. (look at old pads, one or both may have small metel tab on one end) If the new pads have the tab, put that pad where the old pad with the tab was. (ie. tab to the inside) Press pistion in with a 'C' clamp. If it won't go in easly, it may screw in. If the parking brake cable is hooked to the calaper, it probly screws in. Use large pliers to screw in calaper piston. Place calaper over pads and install bolts (lube bolts) Rember to pump brakes befor driving . to get a solid peddle.

Posted on May 20, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: programing instructions for buick 2006 lacrossekeyless remote fob

Transmitter ProgrammingImportant: All transmitters which are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.

  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool. Important: The scan tool must stay connected until all of the transmitters are programmed.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.
Good luck

Posted on Dec 13, 2009

  • 506 Answers

SOURCE: rear brakes on 2006 f150 need changing

There should be two bolts that hold the caliper to the axle assembly. Remove these two bolts and slide the caliper off. At this point check the rotors for abnormal wear or grooves. Depending on how many miles you have on them I would replace them regardless. Before you insert the new pads into the caliper I like to use a C clamp and a piece of flatstock to force the pistons back to their original location. If you don't do this you will not be able to fit the caliper over the rotor. Before installing the caliper if you did buy the new rotors use some brake cleaner to remove any of the cosmoline oil that they are shipped with. Remember to chock your front wheels or use jackstands if you have enough. Good luck!

Posted on Feb 13, 2010

  • 1 Answer

SOURCE: change headlight 2006 Buick LaCrosse

2006 Buick Lacrosse - The headlight (DIM) will stop working and then a day or two later start back. Took back to where it was purchased and they said they had it fixed but happened the very same day. Any ideas?

Posted on Jul 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix the third brake light appearing in the rear window on a 2006 Buick LaCrosse?


https://s26.postimg.org/s7ph40vm1/chm.jpg

Click on the link.
Wiring diagram for center high mount. Check voltage and ground. The white wire is voltage and the black wire is ground. The voltage comes from bcm. Use a test light, while somebody steps on the brake or use a heavy object on brake pedal. If there is voltage, the test light will light up. To check ground, black wire, with test light, Have test lite touching battery voltage, touch the black wire terminal, if the lite comes on, at least the ground is good enough to lite the test light. If you have good voltage and ground then I suspect the lamp assembly is faulty.

Sep 09, 2017 | Cars & Trucks

3 Answers

One high beam not working 2006 Buick lacrosse


Sampson, sounds like a bunt out bulb, which will need changed.
If you feel comfortable doing it yourself. Basically three screws, and you have to pull one plastic fastener from the fascia (bumper) and pull the bumper back a bit, and pull the assembly out. I believe it is in the manual, not bad to do. I will post a link to tell or show you how to do it. Press the helpful button

Headlight Change 2005 2009 Buick LaCrosse 2006 Buick LaCrosse CX 3 8L V6

2008 Buick LaCrosse Headlight Replacement

Thread how do replace the headlight bulb in 2005 buick lacrosse

Headlight Bulbs

Feb 13, 2016 | Buick Cars & Trucks

1 Answer

2006 buick lacrosse My car is running hot I changed the water pump radiator and thermostat already


I am currently having the same problem with my 2006 Buick lacrosse I changed water pump, thermostat , radiator, radiator car bled it add dex coolant but it's still running hot...got it tested for the psi n it came bak good reading

Jan 17, 2014 | 2006 Buick LaCrosse CXL

1 Answer

Replacing brake pads in 2006 Buick Lacrosse CXL - how do reset emergency brake to get new pads in?


REAR BREAKS(I ASUME) REQUIER A SPECIAL TOOL TO SCREW THE REAR CALIPERS IN SO YOU CAN INSTALL PADS

Nov 15, 2011 | Cars & Trucks

1 Answer

2006 lacrosse brake job estimate


If your car needs rotors and pads front and rear , a shop will charge between 4-600 for complete brake job.

May 03, 2011 | 2006 Buick LaCrosse

1 Answer

How do you compress rear brake caliber on lacrosse


You cannot just "compress" there rear brake pistons, they have to be de-adjusted because the parking brake must reset them to take up play in that system. A special tool is required to reset the piston.

Feb 24, 2011 | 2006 Buick LaCrosse

1 Answer

HOW DO I CHANGE THE REAR BULB ON A 2006 BUICK LACROSSE


Asuming you mean taillight/turnsignal, and not highmounted brake light:
1.open the trunk
2.Remove 4 wingnuts on trunk trim (there are two on each side)
You can do it by only removing 2 on one side, but it makes a nicer job,
3.Pull back the trunk "trim" the carpeted cardboard
4.Remove 2 wingnuts which hold the taillight assembly in place
Pull out the taillight assembly; you might want to remove (i.e. unattach or unplug) the wiring harness
5.Turn the particular bulb's socket (there's 5 back there: 2 tail, 1 back up, 1 side marker, 1 brake/turn) counterclockwise, and it removes from the assembly, holding the bulb.
6. Pull out bulb and replace.
6. Reverse steps to reassemble.

Dec 30, 2010 | 2006 Buick LaCrosse

1 Answer

Is it easy to change a rear turn signal light on a 2006 Buick LaCrosse


yes. open the trunk. Then pull back the carpet over the rear of trunk then take off two or three bolts. then the light should come off.

Aug 25, 2010 | 2006 Buick LaCrosse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

637 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...