Question about 2005 Chevrolet Equinox

Open Question

Where is the DRL resistor located on a 2006 equinox?

My relay is fine but drl are not coming on

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Low beam and DRL will not come on

how do you change the headlight not the bulb on a Chevy 05 Equinox

Posted on Jul 19, 2008

SOURCE: 1999 GMC Suburban DRL Work - Headlights/Highbeams Do Not

go to autozone the can help you if you have one they do a lot of things fore nothing including clearing codes

Posted on Feb 21, 2009

  • 3 Answers

SOURCE: REPLACE TAHOE DRL BULB SOCKET

You'll have to order the socket from the GM dealer. I've tried some common park/tail light sockets from Napa, etc. and none fit the lens housing. Part# for my 2004 GMC Sierra is 15306157. (Yours may be different, but probably not)
Remove the headlight lens (unclip & flip the two black steel rods towards you and pull them straight up & out). The lens should almost fall out if the bulb wires didn't hold it in!
There are only two wires, and since incandescent bulbs are not polarity-sensitive, they can go either way without mixing them up. Just cut & strip the old socket's wires, and strip & crimp the new socket on. ****-type crimp connectors were even included with the socket.

Posted on Apr 03, 2009

  • 1 Answer

SOURCE: 99 Cavalier warning lights come on in drive.

Hey, I'm having a very similar problem. Did you figure it out?

Posted on Jan 08, 2010

  • 285 Answers

SOURCE: were is the drl module and relay located

its not really a module,its a diode inside a large black heatsink thats about the size of a pack of cigarettes and its located under the drivers side dash about where your right knee is when sitting behind the wheel,it was a VERY common problem for those to blow and.....no more DRL, hope this helps

Posted on Oct 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my relay and fuse location at for the day time running lights on a 1997 oldsmobile aurora


There is not a separate fuse nor is there a relay ,A LCM - lamp control module controls the DRL .
the lamp control module (LCM) supplies battery positive voltage (B+) through the DRL resistor to the low beam headlamps. The voltage drop across the DRL resistor causes the low beam headlamps to light at a reduced intensity. The DRL are disabled if the high beam headlamps are on or if the gear selector is placed in the PARK position. When the ambient light sensor indicates darkness, the low beams automatically switch to regular intensity.

Lamp Control Module (LCM) (Oldsmobile)
Under the left side of the IP, to the left of the steering column

Daytime Running Lamps (DRL) Resistor
To the left of the engine compartment, near the underhood fuse block

May 01, 2017 | Oldsmobile Cars & Trucks

1 Answer

I need clarification on 2003 Chev Malibu DRL problems:


That piece you think is a ceramic DRL module is a resistor , When in DRL mode voltage to the low beam headlamps circuit goes through that resistor dimming the headlamps from low beam to daytime running lamps . It sounds to me like you need a new resistor ,but without doing some electrical testing it could be a lot of things . The DRL relay in the under hood fuse box could have a problem , could be the BCM - body control module , the ambient light sensor etc... Here is how daytime running lamps work .
Daytime Running Lamps (DRL)
The ambient light sensor is a light sensitive transistor that varies its voltage signal to the body control module (BCM) in response to changes to the outside (ambient) light level. When the BCM receives this signal it will either turn on the daytime running lights (DRL) or the headlights. Any function or condition that turns on the headlights will cancel the daytime running lamps operation. With the headlight switch in the OFF position, the headlights will either be turned ON or OFF, after an approximate 30 second delay depending on whether daylight or low light conditions are sensed. The HTR A/C IGN fuse in the underhood junction block supplies ignition positive voltage to the daytime running lamp (DRL) relay coil circuit. The DRL relay switch contacts are connected to the low beam circuit. When the headlamp switch is placed in the OFF position, the BCM will either turn on or off the daytime running lamps, depending on whether daylight or low light conditions are sensed. The BCM energizes the DRL relay, closing the switch contacts and grounding the low beam circuit. Ground is provided at G101. The DRL illuminate the low beam headlights at a reduced intensity. The DRL will operate when the ignition switch is in the ON position, the gear selector is not in the PARK position and the parking brake is released. When these conditions have been met and the ambient light sensor indicates daytime conditions, the DRL will illuminate.

Feb 25, 2016 | Cars & Trucks

1 Answer

Where is the DRL relay located?


There is no DRL relay , has a lamp control module .
The daytime running lamps (DRL) activate under the following conditions:
?€¢
The ignition switch is in the RUN position.


?€¢
The ambient light sensor indicates daylight.


?€¢
The vehicle is not in the PARK position.

When the above conditions are met, the lamp control module (LCM) supplies battery positive voltage (B+) to the low beam headlamps through CKT 589 (GRY), the DRL resistor, and CKT 12 (TAN). The DRL resistor reduces the voltage supplied by the LCM. The low beam headlamps light at a reduced intensity. The DRL disable if the vehicle is placed in the PARK position. When the ambient light sensor indicates darkness, the low beam headlamps automatically switch from a reduced intensity to a regular intensity.
Lamp Control Module (LCM)
In the center of the IP, below the center heater outlets

Nov 17, 2015 | 1998 Oldsmobile 88

1 Answer

2008 pontiac torrent drl resistor location


The body control module (BCM) and DRL PCM relay are the major elements of the DRL circuit.

Aug 16, 2014 | Cars & Trucks

1 Answer

Location of drl resistor on 2008 equinox


The major components of the DRL system are the body control module (BCM) and the DRL PCB relay.

Aug 16, 2014 | Cars & Trucks

1 Answer

Replacing chevy equinox brake light fuse


4f62cc96-f939-44f0-8eb0-cc6aee80aad2.png

brake light fuse 15 A near the DRL relay (underhood fuse block)

hope it helps

Apr 12, 2014 | 2006 Chevrolet Equinox

1 Answer

I need to know were to find the DRL Module for a 2003 F-150 4x4. My hi and low beem lights work ok , and the auto light sencor works . Its that my Day time running lights do not come on .


The wiring diagram does not show a stand alone drl module for the 03 f150. However it shows 2 drl
relays located in aux. relay box #2 located behind the right side of the dash, left of the glove box.
Also there is the drl resistor located behind the grill, right of the left headlight. Relay #1 is fused at
fuse #5-15a in the fuse block under the left dash. Relay #2 uses fuse #26-10a under left of dash.
Hope this helps.

Nov 17, 2010 | Ford F-150 Cars & Trucks

1 Answer

Daytime running lights do not work?? i have hchanged the relay and the bulbs. Is there a fuse for these also?


Hi Your Equinox's DRL (day time running lights) are fused through the headlight fuses so if your regular lights work its not the fuse. There is a resistor in the DR system that I have seen fail on a few customers vech.s. You also have a ambient light sensor in the system. One thing to check that sounds silly is make sure the parking brake is fully released. if the brake is set the DRL are deactivated. Good luck

Aug 27, 2010 | 2006 Chevrolet Equinox

1 Answer

My wifes Chevy Equinox DRL's are not coming on. When you start the car the light flashes on dash like 5 times then shuts off and the DRL's don"t come on. What could be the problem and how can i fix it ?


You need to buy a new DRL Resistor, about $85 dealer only of course. It's located on drivers side front wheel well I believe it was towards the front bumper. The part is ceramic, just change it out. Mine did the same exact thing and this will fix it!

Aug 16, 2010 | 2005 Chevrolet Equinox

2 Answers

Low beam and DRL will not come on


most headlight switches are pop in style that u just pop out of the dash and gently undo the electrical connector and replace it in reverse order, however all GM cars have individual relays for the lights so You may want to try a new relay first.

Jun 30, 2008 | 2005 Chevrolet Equinox

Not finding what you are looking for?
2005 Chevrolet Equinox Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...