Question about 1992 Geo Metro

1 Answer

1992 Geo Metro Outer CV Joint

Does anybody know how to remove the outer joint to be replaced. I can not find the Cir-clip. I have done many VW's but can not get the outer off to replace it.Thanks. bob

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to split the outer cv joint to replace the rubber boot


lose the central nut of your wheel first,remove the brake caliber loose two bolts holding your suspension arm in one peace and the lower arm bolt and loose the steering arm ball joint pull the hub up and the shaft out is one peace ,loose rubber boot clean housing and look in side you have sir clip with two holes one on etch site remove it with sir clip players grease the joint fit the new boot good luck.

Sep 09, 2012 | 2004 Kia Sedona

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

Can I only disconnect inner cv joint on my 99 metro or do i have to do the outer also?


your best off to do both inner and outer CV joints, but a rebuilt axle is not very expensive and a lot of times is the best remedy, shop around for a rebuilt axle

Jan 28, 2010 | 1999 Chevrolet Metro

3 Answers

When replacing a outer C.V joint boot , do you


you can replace just the outter but you may want to replace the whole axle alot easier

Jan 17, 2010 | 1993 Ford Festiva

1 Answer

Having trouble removing the outer cv gaiter on audi a4 can't get cv drive to come off !


wel if you have removed the joint out of the hub take the bolt you removed screw it back into the joint all the way until it stops make it hard. take heavy hammer and hit the bottom edge of the joint will take good force to knock the joint past the cir clip that holds it in place. then u should be ok. any question return on this thread

Sep 12, 2009 | 2001 Audi A4

1 Answer

02yukon i cannot get the cv joint out from the wheel/brake assem


Remove steering joint.Then bottom ball joint then you should be ok.

Jul 13, 2009 | 2001 GMC Yukon

2 Answers

Seperate outer cv from axel 99 chevy metro


First, did you check the price difference on a complete axle (saves time and aggravation of doing joint & boot) Most times you can get them apart by just putting the axle in a vise and giving the joint a good smack with a hammer. There is a small clip in the end that you can spread, but you have to look carefully to find it. Most people have a hard time getting the boot to stay on and find it has come off a few weeks after they installed it.
That's why I suggest replacing the entire axle which if far cheaper than they used to be!!!

May 28, 2009 | 1999 Chevrolet Metro

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

1 Answer

'97 Geo Metro DriveShaft


hi depends who does the job are you useing a garage or are you getting a mate to do it or are you doing it yourself the parts new if its the outer cv joint it around £20-£30 the complete shaft £80-£100 new could use a breakers it would be in the region of £30-£40 for the complete shaft and an hour to change check around some people are greedy some just ask a fair price best of luck paul

Oct 15, 2008 | 1994 Geo Metro

Not finding what you are looking for?
1992 Geo Metro Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...