Question about 1992 Oldsmobile Cutlass Ciera

Open Question

1992 oldsmobile cutlass ciera V6 3300 engine has no spark from coil pack at # 3 & 6 cyclinders. coil pack is good and ecm board is good ?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22265 Answers

SOURCE: how to change a starter in a 1992 oldsmobile cutlass ciera

disconnect battery,three bolts hold it to bell housing and two wires ,one is the feed the other activates the solonoid Easy job to do but dirty dirt grease and muck

Posted on Jan 24, 2009

Ad
  • 51 Answers

SOURCE: changed spark plugs and wires now car wont start

I know this might be obvious but the obvious is often the problem. Did you replace the coil wire that goes from your coil to the distributor cap? Also, double check to be sure that your wires are connected in the correct order. A little more clarification might help. Does it turn over? Does it just click? When you turn the ignition key then let off does the car clunk or make a wheezing sound?

Posted on Jan 30, 2009

  • 14036 Answers

SOURCE: Changing spark plugs on a 1995 Oldsmobile Cutlass Ciera

ALL YOU NEED IS 3/8 RATCHET WITH A 5/8 SPARK PLUG SOCKET.YOU NEED EXTENSIONS AND UNIVERSAL JOINTS TO GET TO HARD TO REACH PLACES.YOU NEED A SPARK PLUG GAUGE.YOUR SPARK PLUG GAP SETTING WILL BE. 0.060 THAT WILL BE FOR THE 2.2 AND 3.1 ENGINES.

Posted on Aug 17, 2009

Testimonial: "Thank you very much for your advice and time!"

  • 1757 Answers

SOURCE: 1993 oldsmobile cutlass ciera 3.3 liter need

For the 3.3L (6-cylinders):
Firing Order:
1-6-5-4-3-2
Cylinders
2------4------6
1------3------5
(Front of Vehicle)
Ignition Connectors:
___
o-1
o-4
___
o-5
o-2
___
o-3
o-6
(Front of Vehicle)


Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Feb 20, 2010

  • 834 Answers

SOURCE: i need to reset the timing on my 93 oldsmobile

You must have an ignition distributor to be able to reset or change the engine timing. If you do have a coil pack then the engine timing is completely controlled by the computer and there is no timing adjustment.

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you show me a diagram of which spark plug wire goes to what spark plug on a 89 oldsmobile ciera please.


Standing in front of the car looking at the the coil packs, there are three of them. From left to right, the first coil pack is 1 & 4, the second coil pack is 6 & 3, and the third coil pack is 2 & 5. Now standing in front of the engine, the three cylinders in front of the radiator are 2,4 & 6 starting from the belt side of engine and the ones in the back off engine are 1,3 & 5.

Jun 05, 2011 | 1989 Oldsmobile Cutlass Ciera

2 Answers

Need help in replacing spark plugs on a 1995 olds cutless ciera the wiring order with diagram


1995 Oldsmobile Cutlass Ciera 3.1 liter V-6 VIN "M"

zjlimited_352.gif


1995 Oldsmobile Cutlass Ciera 2.2 liter L4 VIN "4"

zjlimited_353.gif


Hope this helps (remember to rate and comment this answer).

May 09, 2011 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

CRANK SENSOR LOCATION FOR 1992 OLDS CUTLASS CIERA


That year Ciera came with two diiferent engines. if you have the 2.5 liter engine it is located under the hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block. If it is the 3.3 liter engine it is located under the hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block. i hope this helps you and good luck.


Mar 15, 2011 | 1992 Oldsmobile Cutlass Ciera

2 Answers

Ihave installed new crank sensor and module board underneath coil pack still no spark


How about changing the Cam Sensor, that's the one that sends the timing (spark) signal from the ECM to the Ignition Module.
Good Luck! Don't forget to rate this post!!

Sep 18, 2010 | 1988 Oldsmobile Cutlass Ciera

1 Answer

Correct positioning of the spark plug wires


For the 2.8 L and 3.1 L firing order : 1 2 3 4 5 6

1-3-5 at rear of the engine
2-4-6 front of th engine

at the other end right positionnning should be written on the coil pack module
Hope it will help
Dan

Dec 29, 2009 | 1989 Oldsmobile Cutlass Ciera

1 Answer

How do i install a ignition model into a 92 Cutlass Ciera


On v-6 it is in the front, tight working area. unplug wiring, remove spark plug wires(mark them for proper order for assembly) unbolt from engine coil packs and remove module, install module(with a little diealetric) and reverse for install.

May 22, 2009 | 1992 Oldsmobile Cutlass Ciera

3 Answers

92olds cutlas cierra, 3.3 liter


how do you check your coils is there a photo that shows you how? or a video, web site




Jun 26, 2008 | 1992 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1992 Oldsmobile Cutlass Ciera Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...