Question about 1997 Nissan Pickup

1 Answer

Speed sensor Check code said speed sensor. Where is it. I've been told it has 2. Been driving with light on for 4yrs.???????????

Posted by on

  • Anonymous Nov 20, 2008

    speed sensor

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 231 Answers

Speed sensors are in the following places, the first one is located in the spedometer.
2) on the transmissio
3) on the rear axle by the backing plate.

Posted on Oct 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have two code error on my jeep grand Cherokee 2007 idle air-control p0507 x3 of them & p2767 input/turbine speed sensor B, could you help me get idea, of what it is?


code p 0507 refers to idle speed control (ISC) system rpm higher than expected==causes -wiring--ISC actuator/IAC valve --throttle motor -- throttle valve tight / sticking---ECM
it als o refers to idle air control(IAC) system--circuit low===causes --wiring short to ground --IAC valve ---ECM
code p 2767 refers to transmission input shaft speed sensor/turbine shaft speed (TSS) sensor B---no signal===causes --wiring---transmission input shaft speed sensor /TSS sensor

Mar 26, 2016 | Jeep Cars & Trucks

1 Answer

What is the corrective action for code c0055?


Apparently it is a speed sensor that is bad. I can see how it is related, just why it throws an ABS code is why I hesitate to say replace the speed sensor. Whether you have 4 wheel drive or 2 wheel drive, the sensor is the closet to the rear drive shaft. If the check engine light is on also for the speed sensor, then I would accept this.

Jun 30, 2015 | 2004 Chevrolet Chevrolet TrailBlazer EXT

1 Answer

Sppeedometer works intermittantly


If the vehicle speed sensor was the cause you would have a check engine light and the transmission would have sifting issues into overdrive, I would think you just have a failing tachometer stepper motor (tiny DC motor) that drives the needle..

Sep 04, 2012 | 1997 Acura CL

1 Answer

1998 Chrysler Sebring convertible Not shifting into drive check engine light came on, error code PO715


DTC P0715 CHRYSLER - Input Speed Sensor 1 Circuit
P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible shifting problems

Possible causes
- Transmission speed sensor circuit is open or shorted.
- Poor transmission speed sensor circuit connection
- Faulty transmission speed sensor

Hope this clues helps to solve it.

Jun 02, 2011 | 2003 Chrysler Sebring

1 Answer

My hyundais check engine light is on so i took it to the shop and they told me that i need to change the speed senso so i bought it when i took it to the machanic so that he could change it he told me...


The vehicle DOES NOT have a vehicle speed sensor (VSS) per se. It DOES however, have speed sensors - INPUT and OUTPUT speed sensors on the transmission. What was the check engine light?... what was the code?

On the 2002 Accent, these sensors cannot be gotten (purchased) separately. The two sensors are part of ONE wire harness and can only be acquired together as one complete unit/harness.

Feb 08, 2011 | 2002 Hyundai Accent

1 Answer

1995 Maxima SE tach does not work at all. Car runs/ drives fine but no tach. 2 check engine light codes one for knock sensor(which I think is actually the o2 sensor from what I have read) the other from...


I am not familiar with this particular car, but the tach problem may be due to the speed sensor. I'd find the speed sensor and have it checked or replaced. My transmission has an input and output sensor. The input sensor feeds the tach (and the computer), the output sensor feeds the speedometer (and the computer). Also the knock sensor is critical to keep the car running efficiently without damaging itself.

Nov 14, 2009 | 1995 Nissan Maxima

1 Answer

Check engine light with following codes p 1529 p0720 p0715


P1529 indicates that your TCM asked the ECM to turn on the check engine lamp.

The range switch and the output speed sensors are the items that are abnormally affecting the operation of the transmission. The diagnostic logic in your computer can distinguish these issues from one another, so you'll definitely want to do both. You have no diagnostic code for the input speed sensor (P0715) listed, so I have made no recommendation to replace it. In my opinion, it's not a labor-intensive repair, so I wouldn't recommend replacing it unless you have reason to believe it's bad.

DTC - P0720 (OUTPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0720 Output shaft speed sensor system
If the output from the output shaft speed sensor is continuously 50% lower than the vehicle speed for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h or more, it is judged to be an open circuit or short-circuit in the output shaft speed sensor and diagnostic trouble code No. P0720 is output. If diagnostic trouble code No. P0720 is output four times, the transmission is locked into 3rd gear or 2rid gear as a fail-safe measure.
Probable cause
Malfunction of the output shaft speed sensor
Malfunction of the transfer drive gear or driven gear
Malfunction of connector
Malfunction of the TCM

DTC - P0715 (INPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0715 input shaft speed sensor system
If no output pulse is detected from the input shaft speed sensor for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h (19 mph) or more, it is judged to be an open circuit or short-circuit in the input shaft speed sensor and diagnostic trouble code No. P0715 is output. If diagnostic trouble code P0715 is output four times, the transaxle is locked into 3rd gear or 2nd gear as a fail-safe measure.
Probable cause
Malfunction of the input shaft speed sensor
Malfunction of the underdrive clutch retainer
Malfunction of connector
Malfunction of the TCM

Is needed replace.

Nov 04, 2009 | 2001 Hyundai Elantra

2 Answers

I have a 2001 Mitsubishi Eclipse GT Neutral light blinking


Could be a wiring issue if you already replaced the speed sensor. I believe there are 2 speed sensors on that tranny though, and both are usaully replaced at the same time.

Jun 05, 2009 | 2001 Mitsubishi Eclipse

1 Answer

1996 Nissan 200SX Speed Sensor


It is possible that this code can be caused by the speedometer head itself. The signal from the speed sensor is processed in the speedometer and then sent to the ECM. Check the two screws on the back of the speedometer to see if they are loose. If so retighten and drive to see if the check engine light comes back on. If they are tight, replace the speedometer assembly( I think you gave to purchase the entire meter assembly). If the light still comes on, which is unlikely, you will need to check the wire going to the ECM.

Nov 29, 2008 | 1996 Nissan 200SX

2 Answers

Engine shuts off after driving a few miles


I’ve had a problem with my 94 LHS stalling at high speeds, but I would have to wait a little while before the car would start up. If I were you I would have someone have a look at you cam or crack modules.
Also, I’ve had problems with my 99 LHS not starting and I was told it might be the sensor for the gear shifter

Oct 02, 2008 | 1999 Chrysler Concorde

Not finding what you are looking for?
1997 Nissan Pickup Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...