Question about Cars & Trucks

Open Question

Ford transit conect 2002 where is the heater resistor for the heater blower

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75817 Answers

SOURCE: blower motor resistor

It is under the hood in the heater case (passenger side), the right side of the case near the firewall as you face the engine.

Posted on Sep 02, 2008

  • 1 Answer

SOURCE: Diagram of Location of a Starter Motor on Ford Transit 2002/2003

replaced starter motor 53 plate t350 90 transit van. lots of dust replaced fly wheel and clutch and sensor :speed up to 50 miles per hour and temp gauge goes up and cuts power

Posted on Dec 08, 2008

  • 1 Answer

SOURCE: locating heater blower motor resistor

the resistor is behind your glove box. open the box and push in the sides to release it and let it hang down...the resistor is right there. I didn't try to replace it, a friend did it, but the part was under $20.

Posted on Feb 01, 2009

  • 2 Answers

SOURCE: 2002 dodge grand caravan heater blower only works on high spped

If you are looking for the fan blower resistor, it is located behind the glove box. No tools need to get to it and a nut driver to remove the 2 screws to replace it. A 20$ part.

Posted on Feb 05, 2009

  • 4 Answers

SOURCE: 2002 Chevy Impala Blower resistor location

It is on the passenger side, you have to remove the black plastic kick plate, below the glove box, to expose it (held in place with 2 latches and 1 push pin). The resistor is in front of the blower motor ( sandwiched between the motor housing and the firewall) it is tricky to get to, i think when i changed mine i didnt replace all the screws as they were difficult to remove and even harder to replace. Good Luck, Mike

Posted on Apr 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does heater fan only run on high?


The speed control resistor may have failed.

Feb 13, 2016 | 2002 Ford Taurus

1 Answer

Would like to know what fuse is for my blow heater in my 54 plate ford transit


If your blower has multiple speeds, a fuse may not be at fault.

The speeds are set using a tapped resistor which may be on the firewall of the engine compartment.
If these fail. often the highest speed will still work but none of the others.

There are too many shapes and sizes for these but many are shown here if you find the fuse is OK:

heater blower resistor Bing images

Feb 03, 2015 | Ford Cars & Trucks

1 Answer

2002 MERCURY GRAN MARQUIS NO LOW AC BLOWER


More often than not, the Blower Motor Resistor would be at fault. It controls the speed of the Blower Motor by varying its speed revolutions. The Blower Motor Resistor is located under the hood under the heater hoses. You can purchase one from E-bay, Amazon, or check your local Auto Parts store(try to get the best price). To get an idea of where the Blower Motor Resistor is situated and what it would take to replace it, go to www.youtube.com. Type ......how to replace blower motor resistor ford crown vic.... and the video will pop up. There should be another video under it with the caption.....2003 ford crown
Victoria blower motor resistor swap... Watch both videos as they contain two different approaches in replacing the unit.

Jun 08, 2014 | 2002 Mercury Grand Marquis

1 Answer

No heat in my 2002 Ford E150


Did you check the fuse ? 12v direct to blower motor ? Or check the control switch ?

Dec 27, 2013 | Cars & Trucks

2 Answers

F150 2004 blower working only on high position.


this is because your blower motor resisters are burned out for speeds 1,2 & 3. High speed does not have a resister.

Replace the resister. If it goes a 2nd time, it is because your blower motor is failing & drawing too much current.

it is behind the glove box I think. It is in the plenum case where air blowing on it keeps it cool.

Easy repair. May need to access throught glove box which should open all the way down when you squeeze the sides in.

Go to tascafordparts.com for a discounted resister.
Please rate as solved problem if this is what you needed.

------------------------------------------------------------------------------
Manual Climate Control System Outputs
Blower Motor Switch Resistor
Blower Motor Resistor Coils 9ba1105.gif Blower Motor Thermal Limiter 47afe58.gif The heater blower motor switch resistor has the following features:
  • The assembly is located on the passenger side of the plenum assembly behind the glove compartment (06010).
  • Three resistance elements are mounted on the resistor board to provide four A/C blower motor speeds.
  • Depending on the heater blower motor switch position, series resistance is added or bypassed in the A/C blower motor circuit to decrease or increase A/C blower motor speed.
  • An overheating protective device (thermal limiter) will open the resistor coil circuit when the temperature reaches 121°C (250°F), interrupting the blower motor operation in all speeds except HI.
  • The thermal limiter cannot be reset and is not serviceable.

Mar 23, 2009 | 2004 Ford F150

1 Answer

2002 F-150 blower motor stopped working.


There are 4 things to check out to pin point the problem: the switch it's self, the blower relay switch, resistor block, and the blower motor it's self. good luck

Jan 20, 2009 | 2002 Ford F150 Regular Cab

1 Answer

Blower problem


The blower motor resistor:
  • is located on the heater core and evaporator core housing near the blower motor.
  • has three resistor elements mounted on the resistor board to provide four blower motor speeds.
  • depending on the blower motor switch position, series resistance is added or bypassed in the blower motor circuit to decrease or increase blower motor speed.
  • has an overheating device (thermal limiter) that will open the resistor coil when the temperature reaches approximately 184°C (363°F) , interrupting the blower motor operation in all speeds except high.
  • is serviced as an assembly. The thermal limiter cannot be reset and is not serviceable.
REMOVAL
  1. Lower the glove compartment.
  2. Remove the screws and position aside the 4x4 control module.
  3. Remove the blower motor resistor.
4 Disconnect the electrical connector. 5 Remove the screws and the blower motor resistor. INSTALLATION
  1. To install, reverse the removal procedure.

Nov 06, 2008 | 1995 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...