Question about 2002 Chevrolet Blazer

1 Answer

Ignition key lock cylinder 2002 s10 - 2002 Chevrolet Blazer

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Randy, where do I start the hole?

Posted on Jun 09, 2015

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: ignition lock cylinder

take the registration or title to your local dealer and have a key made from the VIN

Posted on Jun 30, 2008

kd6rhd56
  • 400 Answers

SOURCE: I cannot remove ignition key from lock on Blazer S10

sounds like the igniton key swich has a problem possibly a electrical short to the key or some component is heating up the key causing not to be removed quicky

Posted on Jul 09, 2009

  • 14585 Answers

SOURCE: i have no keys and

It has to be drilled out. Use a 3/8 " drill bit and try to stay down the center of it. What your trying to do is get a big enough hole in it to get the key pins out You have to drill it about 1 1/4 to 1 1/2 " deep, the start wallowing it out.

Posted on Jul 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1610 and P1614 Keys won't turn for Lock Position on Ignition Lock Cylinder


Not sure what the problem here is.
The codes are for the security system - - the key is not sending a signal or the right signal for the car to start.
Could be a problem with the lock cylinder which may have a sensor for the key inside it.

Jul 02, 2012 | 2002 Nissan Altima

2 Answers

Can't put key into ignition


Hello: It sounds like the tumblers came loose in the ignition lock cylinder. You will need to replace the lock cylinder and possibly the key to. A worn key is hard on the lock cylinder.

Jun 07, 2011 | 2002 Cadillac Deville

1 Answer

How do i replace the key cylinder?


SECTION 211-04: Steering Column 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal and Installation
All vehicles
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Turn the ignition keys to the ON position.
Early build vehicles
  1. Remove the upper steering column shroud.
  1. Remove the screws and the lower shroud.
  1. Using a small tool, press the ignition lock cylinder release button and pull the ignition lock cylinder out.
Late build vehicles
  1. Using a small tool, press the ignition lock cylinder release button in the hole and pull the ignition lock cylinder out. Usually, the key has to be in the oN position to do this step.
All vehicles
  1. To install, reverse the removal procedure.

Mar 23, 2011 | 2002 Ford Escape

2 Answers

1991 S10 Ignition Lock Cylinder will not turn with key. Had new key made. Still, the ignition switch will not turn. It is on a 1991 Chevy S-10.


Hi,
This may or may not help. Is key hanging up in cylinder? If so, spray some wd 40 or graphite into the switch. Also, if steering wheel is turned fully in either direction, then your steering wheel lock may be preventing you from truning key. Try shaking the wheel while turning the key. Lastly your ignition switch may be shot.

Jul 10, 2010 | 1991 Chevrolet S-10

1 Answer

The code says i am losing voltage to the transmission due to a failed inigtion switch. Are they talking about the key switch or some module if so were is it?


an "ignition switch" is generaly the switch which is activated by the key fob.

To Remove:
  1. Disable the SIR system by disconnecting the negative battery cable.
  2. Remove the left insulator panel and knee bolster from under the instrument panel (I/P).
  3. Remove the trim covers from the steering column.
  4. Release the ignition lock cylinder locking tab by inserting an allen wrench into the hole on the top of the ignition lock cylinder housing and pushing down.
  5. Remove the ignition lock cylinder from the ignition lock cylinder housing.
  6. Disconnect the passlock and key buzzer from the ignition lock cylinder housing.
  7. Release the ignition switch tabs by inserting a J 42759 ignition switch connector release tool into the ignition lock cylinder housing.
  8. Remove the ignition switch from the ignition lock cylinder housing.
  9. Disconnect the ignition switch connector. .
when you install the new one, just make sure the ign switch is in the same position as the old one was before assembly :)

May 20, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

How do you program the keyless remote on a 2002 Intrigue?


1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode.


Good luck and thank you for using Fixya

Mar 09, 2010 | 2002 Oldsmobile Intrigue

1 Answer

For dgnoid: Car is 2002 Buick Regal. Husband is blind and I thought it would be cool for him to have remote key to lock and unlock car more easily, unfortunately, it did not come with instructions on how...


IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)


6.
Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)


7.
Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).

10. Perform the previous step to program up to four transmitters (including your
old ones).

11. Remove the ignition key in order to exit the Program Mode.


Jun 29, 2009 | 2002 Buick Regal

1 Answer

Ignition will turn when key is inserted 1996 Chevy S10


Maybe the steering wheel lock causing this problem, try rocking the wheel left to right and back the other way, if that doesn't work the lock cylinder is defective and must be replaced.

May 21, 2009 | 1996 Chevrolet S-10 Pickup

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...