Question about Cars & Trucks

Open Question

How do I adjust the high amd low beam for yamaha mio? It is inverted. The high is low and vice versa

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2003 A4 low beam adjustment

Go to mechanic !

Posted on Oct 21, 2008

Ad
  • 840 Answers

SOURCE: Adjusting the low beam headlight

its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

Posted on Jan 31, 2009

  • 112 Answers

SOURCE: headlights fail to turn on after several attempt

Bad headlight relay.

Posted on Mar 26, 2009

RonPark
  • 855 Answers

SOURCE: high beams shine too close to the vehicle. How do

The alignment of the head lights aligns both at the same time since there is only one bulb. It sounds as if the bulbs may be the problem. The filament in the bulb may be starting to go bad, or if bulbs are new the filments are bad. If the low beams are also off check that bulbs are installed and seated properly. If they are they will need alignment. If alignment is needed go to a shop that has the tool ta align head lights, They don't just pull car up to a wall and guess that its right or close.

Posted on Oct 14, 2009

Testimonial: "Thank You- I have had the car back to the dealer 3 times. I think I will try another dealer. Thanks again"

RonPark
  • 855 Answers

SOURCE: In adjusting the headlights on a 2003 Olds Alero,

Unless a car has been in an accident it is very rare that the adjustment of haedlights change. the usual problem as in your case sounds as if the headlamp is not installed properly. It is either loose or not seated properly. So check there first.

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left low beam of my A4 model 2011 is very low, how can I adjust to higher level


place the car 3ft from a reflective wall turn the lights on to high beam and adjust using the adjuster screws at the back of the light. Low beam is part of the high beam so when high beam is set then low beam will be correct.

Dec 26, 2014 | Audi A4 Cars & Trucks

1 Answer

The dimmer switch on my 1999 firebird won't change the headlights from dim to bright, or vice versa. It has a good click to it and the blue light in the dash comes on when they're supposed to


That is a common problem, the switch needs changing if the high and low beams do work, the only problem is that it's an expensive part to replace, try a local wrecking yard they should have a bunch of suitable replacements at a reduced price.

Sep 19, 2012 | Pontiac Cars & Trucks

1 Answer

HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 06, 2009 | 2001 Hyundai Tiburon

2 Answers

Headlights, regular and high beam, are not adjusted properly. Also the high beam sends light straight up in front of the SUV ?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 25, 2009 | 2003 GMC Envoy

1 Answer

How to adjust UK headlights in jeep grand cherokee 99-04? Can one adjust lences to meet european standards?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

The lenses themselves cannot be adjusted to conform between left hand and right hand drive. The reflector or projector of a left hand drive vehicle is designed to throw more light towards the right side of the vehicle and vice versa for right hand drive vehicles.

Sep 15, 2009 | 2004 Jeep Grand Cherokee

2 Answers

How do you adjust the headlights on a 2006 dodge ram 2500 ?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jul 28, 2009 | Dodge Ram 2500 Cars & Trucks

1 Answer

Replacing headlights and adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 02, 2009 | 2005 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...