Question about 2005 Pontiac Aztek

Open Question

HOW DO I BLEED COOLING SYSTEM ON 2003 PONTIAC AZTEK

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 74 Answers

SOURCE: 2004 pontiac aztek cooling fans not working

relays control fans high and low. does fan come on with a/c on?hot wiring only will create more expensive problems in future!!!!! 2004 not 84

Posted on Aug 26, 2008

  • 5 Answers

SOURCE: My gas gauges on my 2003 Pontiac Aztek will not

First check to see if you have any fuses related to ''gages'' thar are bad. You will have to find the wire near the gas tank connection that ''grounds'' the gage. When you disconnect the wire you can ''ground'' or touch it to the body...The gage should sweep from E to F when you do this,if the gage in the dash is good..If not you probably have a bad''sending''' unit in the tank itself..Better known as a ''float assembly.

Posted on Jul 04, 2009

ftw1952
  • 10319 Answers

SOURCE: how do you bleed air pockets out of cooling system in 99 grand am

If a valve is expose on the upper heater hose piping crack that open only when the engine is warmed up for at least 15 minutes. If no valve is seen you will need to loosen one of the heater hose clamps ever so slowly to let the air out. The process to loosen the clamp is not recommended unless you do this first..... When the engine is COLD loosen a hose clamp and remove the hose and put it back on. Thighten the hose clamp snug only. The start the engine to warm up. In about three minutes see if you can twist the hose to move on the fitting. If you can snug the clamo a lttle more and check again. You do not want the hose to come off if too loose. Now that the engine is warmed up for 10 to 15 minutes shut OFF the engine and barely loosen the same clamp 1/4 turn at a time until coolant trickles out. Listen carefully for air escaping too. Air pressure does built up only when the engine gets hot and the air pocket does not move when the engine was cold with the hose removed beforehand. If no air was released upon this proceedure you have a blockage in your system and flushing maybe the only other option using pressure instead forcing the coolant out. Get a can of coolant flush before the power flush proceedure. A radiator pressure tester can be used to power flush with an air fitting adapter installed in place of the guage

Posted on Mar 28, 2010

  • 333 Answers

SOURCE: How to reset the change engine oil light in 2003

If it's like my toyota with key in off position push and hold the milage trip re-set button. Now turn key to on position.Not starting but just to on

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i bleed the power steering system on a 2001 Pontiac Aztek


If you mean getting air out. Simple turn wheel from side to side stop to stop. This will get air out

Jun 08, 2016 | 2001 Pontiac Aztek

1 Answer

2003 pontiac grand am bleeding the cooling system


Look on your exhaust manifold. What you are looking for is a little bleed screw. Mine is painted blue. Yours maybe a different color. When you find it start your engine and let it idle for 3-5 minutes. Make sure your heat is turned on full. With the enging running turn bleed screw counterclockwise till water starts shooting out. Let the water continue to shoot out until you get a steady stream. Once you get that steady stream then tighten. Your system is now bled.

Dec 30, 2013 | 2003 Pontiac Grand Am

2 Answers

How to bleed cooling system pontiac aztek


There are two purge screws. One located at the top of the water pump, the other at the top of the thermostat housing. Unscrew them using a 7mm, leave open until Dexcool starts coming out. You may have to do this several times after the car has been ran. After vehicle has cooled down, remove radiator cap (a bear of a job itself) and check fluid level (bottom of neck). Replace cap and top off reservoir. Another way is to have the frontend on a set of ramps to ensure the radiator is the highest point of the car.

Aug 31, 2012 | 2003 Pontiac Aztek

1 Answer

I need the fuse box diagram for 2003 pontiac aztek


On this website (link below) you find fuse box diagram and description for Pontiac Aztek (2003)

Pontiac Aztek 2003 fuse box diagram Auto Genius

Jun 01, 2011 | Pontiac Aztek Cars & Trucks

1 Answer

I have a 2001 Pontiac Aztek. My brake pedal goes all the way to the floor after have replaced calipers on the front. I put a new master cylinder and booster. Still same problem. My brake fluid has always...


After replacement of any brake componet that requires opening the lines (Brake lines, fluid loss) you have to bleed air out of system. In addition a master cylinder replacement requires a bench bleed before attaching to vehcile.

May 12, 2011 | 2001 Pontiac Aztek

1 Answer

Resetting a service engine soon light on pontiac aztek 2003


take the negitive battery cable off for about five minutes or so and plug it back in and that should fix ur problem

Jul 02, 2010 | 2003 Pontiac Aztek

2 Answers

Temp gauge goes to hot and engine looses power.


hi.. your coolant temp sensor may be getting a bad reading, it also opperates as a compensator so it may effect the power of the vehicle.. check that the engine is actualy hot when it says and your car will probably run alot better if you change it anyway..

Feb 10, 2010 | 2001 Pontiac Aztek

Not finding what you are looking for?

Open Questions:

See all 2005 Pontiac Aztek Questions

2005 Pontiac Aztek Logo

Related Topics:

507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...