Question about 1998 Ford Windstar

Open Question

How to remove center console cover skirt

Rat inside ... need to remove skirt housing cover

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove cd player on 1999 acura el


acura cd player is the last to be removed. first start with center console.
push the seats for and remove the 2 screw on the side of console,2 more inside the storage,remove shifter cover and 2 more waiting underneath.remove ashtray,more screws behind,remove center console 3-4in.and now the radio cover is free to be removed. 4 more screw holding the radio.pull slowly and disconnect the wires behind.install in revers order.
dont forget!!! Acura radio have security code.
good luck

Apr 04, 2014 | Cars & Trucks

1 Answer

Remove the center floor shifter console on a automatic 2005 chevy aveo


The center console needs to be removed, pull the shift plate plastic cover off,
remove two bolts inside the console storage box,
remove the fillips screws that are visible,
the front center storage box also has to be removed,

Feb 26, 2013 | 2005 Chevrolet Aveo Sedan

1 Answer

2005 aveo chevy How do I take the console off


The center console needs to be removed, pull the shift plate plastic cover off, remove two bolts inside the console storage box, remove the phillips screws that are visible, the front center storage box also has to be removed, the bulb is located on the left side of the shifter from underneath.

Feb 26, 2013 | 2005 Chevrolet Aveo

1 Answer

Need diagram for replacing heater core



    Detach the heater core hoses at the firewall. The two black hoses attach near the firewall on the passenger's side of the engine compartment. Squeeze the hose clamps on the end of the hoses with pliers and slide the hoses from the heater core tubes.

    • 4Remove the lower passenger's-side and driver's-side dashboard panels. The two panels are held in with push-pins. Raise the center of the push-pins with a small, standard screwdriver and pull the pins from the panels. Pull the panels away from the dashboard to separate them from the dashboard.
    • 5Remove the center console. Separate the gear select trim piece from the center console, using a small standard screwdriver to pry the trim piece from the center console. Lift it over the shift knob and rotate it to clear the knob. Remove the retaining screws holding the center console in place with a Phillips screwdriver. Lift the console up over the shift knob and remove it from the interior.
    • 6Remove the glove box. Open the door to the glove box. Squeeze the two retaining tabs on the ends of the glove box and pull the glove box away from the dashboard. Remove it from the interior.
    • 7Detach the drain tube from the heater core cover, which is located behind the glove box. The tube can be pulled from the heater core cover by hand. Detach the air intake duct from the bottom of the heater core cover. The air intake duct runs from the bottom of the cover to the center of the dashboard. Remove the duct by hand.
    • 8Remove the retaining screws on the black heater core cover with a Phillips screwdriver. Pull the cover from the heater core and remove it from the interior. Remove the heater core clamp screw with a Phillips screwdriver, pull the clamp away from the heater core, then pull the heater core from the housing.
    • 9Place the replacement heater core against the housing. Place the clamp over the heater core and install the clamp retaining screw with a Phillips screwdriver. Position the heater core cover over the heater core and install the retaining screws with a Phillips screwdriver.
    • 10Attach the drain tube and the air intake duct to the heater core cover.
    • 11Install the glove box. Squeeze the retaining tabs on the sides of the glove box and push it into position against the dashboard. Release the tabs when the glove box is in position.
    • 12Install the center console. Guide the console over the shift knob and install the retaining screws with a Phillips screwdriver. Slip the shift selector trim piece over the shift knob and push it into the center console.
    • 13Place the lower passenger's-side and driver's-side dashboard panel in position. Install the push-pins into the retaining holes, pushing the in center of the pin to engage the pins.
    • 14Fill the radiator with coolant. Most climates require a 50/50 mix of DEXCOOL coolant and water. 2.2L engines require 8.6 qts., 2.4L

Nov 22, 2012 | 2000 Oldsmobile Alero

1 Answer

2010 honda pilot center console removal due to vibration underneath


slide both seats all the way forward remove screws in sides of console if no screws on sides slide seats back and pull center from inside remove two bolts remove side skirt on each side screws under them remove ashtray center pocket screws under it also unplug wire connectors and remove

Jul 29, 2012 | 2010 Honda Pilot

1 Answer

How do you replace a bumper bar ....do you need a whole new skirt


Bumper bar? Skirt?
There is a bumper reinforment behind the bumper cover.
Front or rear???
Either way there are some plastic retainers on top. You may need to remove a grill which would have some sort of retainer. The retainers usually have a center section that prys up some and the retainer will then pull out.
There should also be some retainers on the undersides of the bumper covers.
There is just about always a bolt going up through the bumper cover into the rear quater panel or front fender right in the wheel well edge. Sometimes there is a guide that the cover slide onto as well. You may need to remove the tail lights. There will be nuts on the inside behind the trim panels or the headlights. they usually have some clearly seen bolts holding them in (about 4 give or take)
Unplug any lights and they can usually be left in the bumper cover.
Then off comes the cover.
From there you may find a styrofoam pad. Don't lose that as it helps the cover keep its shape in the heat. And either the reinforment will be bolted or welded to the frame rails.

Sep 06, 2011 | 2007 Toyota Camry

1 Answer

How to remove dashboard


1-Remove the vent/radio housing.
2-Remove the cover panels on either side of the dash that get cover when the door is closed.
3-Remove the panel under the steering wheel.
4- Remove glove box to open space inside of dash.
5-Remove four bolts and connector holding passenger side airbag and remove carefully.
6-Remove cover plate over shifter.
7-Remove the center console.(2 bolts under armrest and 4 screws-2 on either side of the console)
8-Disconnect the wiring harnesses on either side of dash.(White and black connectors. 2 on driver 1 on passenger.
9-Remove the four bolts holding the center of the dash to the floor.
10- remove two bolts on drivers side dash where cover was and same on passenger side.
11- Unbolt the steering column ( 2 bolts under the wheel) and let it rest on floor.
12- The entire dash will remove from the car as 1 piece and each component can be taken out from there.

It isn't worth it to fish for the bolts from the inside. Take the support bar out and work on it outside the car. much faster.

It seems confusing, but easy if you take your time

Aug 04, 2010 | 2003 Kia Spectra

1 Answer

2002 Camry console light bulb is burned out. How


It is under the N. One has to remove the center console and the black part where the letters are: L,N,D etc. It has 2 claws in one side and 2 in the other and one can lift it and see down inside the Sylvania 2723LL lamp with a green cover. Put the green cover on the new lamp. There are not screws only claws and clips and one claw in the Center Console. Where the letters are located it's call Indicator Housing Upper.

Feb 18, 2010 | 2002 Toyota Camry

1 Answer

Light bulb is burned out on gear shift console. How to remover cover?


The center console needs to be removed, pull the shift plate plastic cover off, remove two bolts inside the console storage box, remove the phillips screws that are visible, the front center storage box also has to be removed, the bulb is located on the left side of the shifter from underneath.

Hope helped with this (remember rated this help) Good luck.

Nov 11, 2009 | 1995 Toyota Corolla

1 Answer

Rat caught under center console CD/holder, how do I remove the thing? Yes, is serious question, it is starting to stink.


Have you tried removing the radio unit as that will be the easiest. The main console is a lot trickier as there are screws and bolts all over the place the I believe require you to remove a lot of other components just to get to those hidden screws.
The easiest way to remove the radio is to remove the ashtray assembly. There are a few small phillips head screws in there. Then pull up on the center console cover and push it backward around the gearshift. The actual panel around the radio is held on by a friction cover you can easily pull off. The radio itself has 4 screws on it and then you just pull forward to disengage the wiring harness from the back.

Aug 21, 2009 | 2001 Dodge Intrepid

Not finding what you are looking for?
1998 Ford Windstar Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...