Question about 1996 Ford Econoline

Open Question

Hi, my 1996 ford econovan has a loose alternator belt? can anyone tell me how you tighten it?

There is also a large nut below the belt which has almost unscrewed completely.

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 130 Answers

SOURCE: torque for 85 econovan 1.8 fe motor

a 1.8 in an 1985 econoline van i'm pretty sure that a 240ci inline 6cyl was the smallest engine these use now if you mean 5.8 this is what you want cyl hd.105-112 ft lbs rod blts 40-45 main bearing 95-105 imtake manifold 23-25 good luck

Posted on Feb 10, 2009

  • 234 Answers

SOURCE: loose alternator belt

usaualy there a adjuster

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

How do replace alternator 06 f 250 6.0 l


I tried to find a tutorial video that could better show the process but I couldn't locate one in my database. Hopefully, my written instructions will suffice.

  1. Disconnect the negative battery cable.
  2. Rotate the drive belt tensioner away from the drive belt and remove the drive belt from the alternator pulley.
  3. Detach the electrical harness connectors at the alternator assembly.
  4. Disconnect the positive battery cable and remove the nut and washer.
  5. Remove 2 front alternator bolts.
  6. Remove the rear alternator support bracket retaining bolts and the support bracket.
  7. Remove the alternator from the vehicle.

To install:

  1. Place the alternator in position and loosely install 2 front alternator retaining bolts.
  2. Install the alternator bracket and 3 alternator bracket bolts. Tighten to 84 inch lbs. (10 Nm).
  3. Tighten 2 front alternator retaining bolts to 19 ft. lbs. (26 Nm).
  4. Connect 2 electrical harness connectors to the alternator assembly.
  5. Connect the positive battery cable and install the nut and washer. Tighten the nut to 72 inch lbs. (8 Nm).
  6. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley.
  7. Connect the negative battery cable.
  8. Start the engine and check for proper charging system operation.

Jun 17, 2012 | 2008 Ford F 250 Super Duty 4WD

2 Answers

Where is the voltage regulator located?


The voltage regulator is built into the Alternator.

May 13, 2011 | 2003 Ford Expedition

1 Answer

Replacing alternator in 89 acura legend how do i relese belt


There is a 10 bolt on the left which does the adjusting it is behind a "U" shaped alignment washer midway down the stud that you took the nut off (that held the middle of the 3 cover holdowns). This bolt goes through the left alternator 12 nut/stud and you will also have to take out the 14 bolt on the right. Turn the bolt clockwise and it will take the tension off the belt so you can get it off the pulley. To get the alternator back on point the 12 stud at an angle to receive the left side of the alternator while keeping it against the engine removal flange and in the "U". Drop the alternator into position on the right and put the large 14 bolt through. Now put the 12 nut onto the left stud and count how many times you drop the nut. You can tape it to a screwdriver and get it into position where you can get a quarter turn on it. Replace the belt (if new you will need to support the engine and take off the left side mount) and tighten the 10 until the belt has 1/2" play at the middle. Not too tight but not loose enough to move the pulley by hand. Tighten the 12 (left) and 12 (right) and replace the wires and covers. Get bandaids for your wounds.

Aug 05, 2010 | 1989 Acura Legend

1 Answer

Replacing the alternator


Fig. : Alternator mounting-2.2L engine

efa282c.jpg

REMOVAL & INSTALLATION

(2.2L Engine)
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the vehicle, then remove the passenger side tire and wheel assembly for access to the rear of the alternator through the wheel well.
  3. Working through the wheel well, unfasten the alternator brace-to-block bolt, then remove the brace-to-intake nut and the brace-to-engine stud nut.
  4. Unplug the alternator wiring connector, then remove the battery terminal nut and wire.
  5. Carefully release the serpentine belt tension and remove the belt from the alternator pulley. Do not allow the tensioner to snap back into position once the belt is off the pulley.
  6. Loosen the alternator retaining bolts, then support the alternator and remove the fasteners. Remove the alternator from the vehicle.

To install:
  1. Position the alternator in the vehicle and loosely install the retaining bolts.
  2. On 1994-98 models, tighten the top alternator bolt to 22 ft. lbs. (30 Nm) and the bottom bolt to 32 ft. lbs. (43 Nm).
  3. On 1999-99 models, tighten the rear bolt to 37 ft. lbs. (50 Nm) and the front bolt to 18 ft. lbs. (25 Nm).
  4. On 1994-98 models, install the alternator brace, then tighten the retaining nut(s) and bolts to 22 ft. lbs. (30 Nm).
  5. On 1999-99 models, install the alternator brace, tighten the brace-to-alternator and brace-to-intake retainers to 18 ft. lbs. (25 Nm). Tighten the brace-to-engine stud nut to 37 ft. lbs. (50 Nm).
  6. Install the battery terminal wire and tighten the retaining nut, then engage the alternator wiring connector.
  7. Hold the serpentine drive belt tensioner, back off the belt while slipping the belt over the alternator pulley. Gradually lower the tensioner into contact with the belt, then check for proper alignment and tension.
  8. Connect the negative battery cable.



Fig. : Alternator mounting-4.3L engine


3fdb6af.jpg

REMOVAL & INSTALLATION
(Except 2.2L Engine)
  1. Disconnect the negative battery cable.
  2. Remove the air inlet duct assembly, if necessary.
  3. Carefully relieve the serpentine drive belt tension, then remove the belt from the alternator pulley. Do not allow the tensioner to snap back into position once the belt is off the pulley.
  4. Remove the nut retaining the radiator hose brace to the back on the alternator.
  5. If equipped, unfasten the retainers, then remove the brace from the engine and/or the alternator.
  6. Disconnect the battery terminal boot wiring from the back of the alternator, then unplug the regulator wiring connector.
  7. Support the alternator and remove the mounting bolts (usually 2) from either side of the alternator, then remove the alternator from the vehicle.
To install:
  1. Position the alternator in the vehicle and loosely install using the mounting bolts.
  2. If equipped, loosely install the brace to the engine and/or alternator.
  3. Tighten the left or front alternator retaining bolts to 36 ft. lbs. (50 Nm), the right or rear alternator bolt to 18 ft. lbs. (25 Nm), the brace bolt to 18 ft. lbs. (25 Nm) and/or the brace nut to 22 ft. lbs. (30 Nm), as applicable.
  4. Connect and secure the alternator wiring.
  5. Carefully relieve the serpentine drive belt tension and position the belt over the alternator pulley, then slowly release the tensioner into position.
  6. If equipped, install the air inlet duct assembly.
  7. Connect the negative battery cable.

I hope helps with this. Good luck (remember rated this help).

Jan 05, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

How to remove alternator from 1997 Chrysler Concorde?


e
3.3L Engine

  1. Disconnect the battery negative - cable.
b9a39c6.jpg

Fig. Wiring and nut locations



  1. Disconnect the alternator field circuit plug.
  2. Remove the B+ terminal nut and wire.
  3. Loosen the adjusting T-bolt, but do not remove it.
  4. Loosen the pivot bolt, but do not remove it either.
  5. Remove the alternator drive belt.
  6. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  7. Remove the alternator.
To install:
  1. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  2. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  3. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  4. Connect the negative - battery cable.

3.5L Engine

  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
3260271.jpg

  1. Loosen the belt adjusting bolt.
  2. Remove the alternator drive belt.
  3. Remove the bracket.
  4. Remove the lower mounting bolt and pivot bolt.
  5. Remove the alternator.
  6. Disconnect the alternator field circuit plug.
  7. Remove the B+ terminal nut and wire.
To install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1997 Chrysler Concorde

1 Answer

Remove and replace alternator


2000 Ford Truck Expedition 4WD 4.6L EFI 8cyl

Alternator - REMOVAL & INSTALLATION

4.2L Engine

  1. Disconnect the negative battery cable.
  2. Disconnect 2 alternator and voltage regulator electrical harness connectors at the alternator. To disconnect push-on type terminals, depress the lock tab and pull straight off.
  3. Remove the positive battery cable nut and remove the positive battery cable at the alternator.
  4. Rotate the drive belt tensioner away from the drive belt and remove the drive belt from the alternator pulley.
  5. Remove 3 alternator retaining bolts and remove the alternator.
To install:
  1. Place the alternator on the engine and install 3 alternator retaining bolts. Tighten the bolts to 18-22 ft. lbs. (20-30 Nm).
  2. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley.
  3. Connect 2 alternator and voltage regulator electrical harness connectors.
  4. Connect the positive battery cable to the alternator and install the nut and washer. Tighten the nut to 84 inch lbs. (10 Nm).
  5. Connect the negative battery cable.
  6. Start the engine and check for proper charging system operation.
4.6L, 5.4L and 6.8L Engines

f52fc60.jpg

Fig. 1 Detach the connectors from the alternator

ffe1937.jpg

Fig. 2 Remove the nut and the battery cable from the post on the rear of the alternator

6ce39ae.jpg

Fig. 3 Remove the 2 front alternator mounting bolts and ...

45a032e.jpg

Fig. 4 Remove the alternator from the engine by carefully lifting it up and...

6513790.jpg

Fig. 5 ... out of the engine compartment
  1. Disconnect the negative battery cable.
  2. Rotate the drive belt tensioner away from the drive belt and remove the drive belt from the alternator pulley.
  3. Detach the electrical harness connectors at the alternator assembly.
  4. Disconnect the positive battery cable and remove the nut and washer.
  5. Remove 2 front alternator bolts.
  6. Remove the rear alternator support bracket retaining bolts and the support bracket.
  7. Remove the alternator from the vehicle.
To install:
  1. Place the alternator in position and loosely install 2 front alternator retaining bolts.
  2. Install the alternator bracket and 3 alternator bracket bolts. Tighten to 84 inch lbs. (10 Nm).
  3. Tighten 2 front alternator retaining bolts to 19 ft. lbs. (26 Nm).
  4. Connect 2 electrical harness connectors to the alternator assembly.
  5. Connect the positive battery cable and install the nut and washer. Tighten the nut to 72 inch lbs. (8 Nm).
  6. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley.
  7. Connect the negative battery cable.
  8. Start the engine and check for proper charging system operation.
5.8L and 7.5L Gasoline Engines and 7.3L Diesel Engine
  1. Disconnect the battery ground cable.
  2. Label and detach the connectors from the alternator.
  3. Release the tensioner and remove the drive belt from the alternator pulley.
  4. Remove the alternator retaining bolts.
  5. Remove the alternator from the vehicle.
To install:
  1. Position the alternator and install the retaining bolts. Tighten the retaining bolts to 15-21 ft. lbs. (21-29 Nm).
  2. Install the drive belt.
  3. Attach the alternator connectors.
  4. Connect the battery ground cable.

I really hope help you with this (remember rated this help) Good luck.

Oct 13, 2009 | 2000 Ford Expedition

1 Answer

How do I tighten the tension on the alternator belt? I have a loose belt on my 1993 Legacy, and I don't know which bolt(s) to loosen to tighten the tension on the belt. Also, is this a pretty easy fix, or...


there is a nut on the idler pulley under alternator loosen this then there is a bolt above pulley tighten this then tighten nut on pulley you should be good to go

Aug 19, 2009 | 1993 Subaru Legacy

1 Answer

Cant remove the nut so water pump comes out


If your talking about large nut for fan to pump it is let hand thread,put wrench on and slao with hammer while belt still on.this will ussualy break it loose.

Jun 18, 2009 | 1996 Ford Explorer

1 Answer

Torque for 85 econovan 1.8 fe motor


a 1.8 in an 1985 econoline van i'm pretty sure that a 240ci inline 6cyl was the smallest engine these use now if you mean 5.8 this is what you want cyl hd.105-112 ft lbs rod blts 40-45 main bearing 95-105 imtake manifold 23-25 good luck

Feb 10, 2009 | 1985 Ford Econoline

Not finding what you are looking for?
1996 Ford Econoline Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...