Question about 1999 Oldsmobile Intrigue

Open Question

How to replace head gaskets on 2001 olds intrigue

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 91 Answers

SOURCE: HAVE 2001 OLDS INTRIGUE WITH HEAD GASKETS OUT NEED

Sign up for the online manuals at alldata.com.

Posted on Jun 14, 2009

  • 599 Answers

SOURCE: 2000 Olds Intrigue coolant is leaking from the

have the car pressure tested to confirm where the leak is from,then get back to me Thanks Ray

Posted on Nov 13, 2009

  • 538 Answers

SOURCE: NEED SCHEMATIC TO REPLACE HEAD GASKET ON A 2000

Good luck with that, it's a big job. There are no external timing marks on the crankshaft pulley, if fact the pulley is not even keyed to the crank. The best way is to remove the timing cover to gain access to the chain tensioner, crankshaft mark and balance shaft mark, you'll need a good three jaw puller to get the pulley off it's a tight press fit. There are darken links on the timing chain that have to all line up with the marks on the cam sprockets, crankshaft and balance shaft. If you try to do it without pulling the timing cover and you let any slack in the timing chain the balance shaft will most likely be out of time. I have the engine out of the car and it's still a big job, I don't know if it's even possible to do with engine in the car. There are 3 small bolts down in the area where the timing chain is, don't forget to take those out. You don't need to remove the cams to get the head bolts out. They tell you to use special tools to keep the cams from turning once chains are removed, a piece of 3/8" flat steel or aluminum plate works. On the back end of the cams there is a flat machined on all the cams when the timing marks are lined up those flats are all in a line. You slip the flat plate under the cams, you may want drill a hole in the plate and bolt it down with the valve cover bolt at the end of the head. I bought a Haynes Manual for that car, it's not the best, but it gives you most of the information you need. Make sure you get all the gook out of the bolt holes use blow gun with a long line on it, like a piece brake line. Spray some brake parts cleaner or carb cleaner in the hole then blow them dry. Oil the threads and the washers or use anti-sieze. When you torque the head bolts it say's to torque them to 22 ft.lbs. and then turn the bolts another 60+60+60 degrees totaling 180 degrees or a half turn. Good luck!

Posted on Dec 01, 2009

  • 31 Answers

SOURCE: are the heads in the olds. intrigue a 2001

no there are no internal heads... the heads are the top of the engine... sometimes they are covered by plastic peices but there not internal

Posted on Jan 31, 2010

  • 1915 Answers

SOURCE: We are replacing a head gasket on a 2001 Olds

It is a tight fit, but it can be removed if you remove the 'shelf' above the engine that houses the wiper assemply, and I have seen people lower the engine by unbolting the cradle-put a block of wood between the jack and the engine/transaxle, and unbolt the cradle bolts, lower it so you have enough clearance to pull it out (works on both 3.5 and 4.0 motors, it really helps to have 2 people to do this-also, if you haven't don it yet.scribe the bolts and slots on the hood bolts and remove the hood, make your life much more enjoyable.

Posted on Apr 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Olds Intrigue is overheating.


u have a restriction some wear obviously have u had the head gaskets replaced at some point there common and its common to install the wrong one as well

Oct 26, 2012 | 2001 Oldsmobile Intrigue

1 Answer

Ihave a 2001 olds intrigue oil is getting into the intake making car smoke i have changed the pcv and the intake gaskets but still getting oil in the intake bad how is the oil getting into the intake.


It sounds to me like the valve stem seals might have shrunk, if that is the case you will need to have the cylinder head reconditioned.
Go to a good workshop and see if they will do an exchange, that means you take your cylinder head off and swap it for a reconditioned one. Or have your mechanic do that if you don't want to go through the process.

Oct 04, 2011 | 2001 Oldsmobile Intrigue

1 Answer

What could cause an over heating problem in a 2001 oldsmobile intrigue?


there is many things that can cause that not enough cooling in the system thermostat is sticking bad head gasket of a bad head on one of the cylinder give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Oct 16, 2010 | 2001 Oldsmobile Intrigue

1 Answer

1998 Olds Intrigue with white smoke coming out of exhust all the time also the heats up when sitting in Drive or Park.


your head gasket is no good . you'll need to get head gasket job unless you do this motor will seize up its smoking because its mixing ur antifreeze and engine oil..

Feb 15, 2010 | 1998 Oldsmobile Intrigue

1 Answer

Are the heads in the olds. intrigue a 2001 internal ?


no there are no internal heads... the heads are the top of the engine... sometimes they are covered by plastic peices but there not internal

Jan 30, 2010 | 2001 Oldsmobile Intrigue

1 Answer

Gas pouring from tailpipe


Make sure you use OEM Injectors. The white smoke might come at a 3.5 from a bad gasket bewteen the intake manifold and the throttle boy or if you have the 3.8 from bad gaskets between the intake manifold and the engine.

Jul 13, 2009 | 2001 Oldsmobile Intrigue

2 Answers

Fuel pump reset switch 98 olds intrigue


I recently changed my head gaskets and exhaust gaskets but now that I put it all together it does not stay running, Do I have my firing order wrong ? Also can I have a picture of how the wires should be placed

May 17, 2009 | 2002 Oldsmobile Intrigue

Not finding what you are looking for?
1999 Oldsmobile Intrigue Logo

Related Topics:

569 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...