Question about Isuzu Rodeo

Open Question

2000 rodeo 4l30e please help

Trying to change my band apply solenoid in my 4l30e trans my only problem is i dont know if i have to drop the valve body to pull the roll pin out any help would be greatly appreciated thanks.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
justuscc
  • 360 Answers

SOURCE: honda passport with a 4L30E

sounds like a solenoid issue... or the trans computer good luck

Posted on Oct 01, 2008

Ad
  • 1 Answer

SOURCE: 4L30E transmission control Module 1999 Isuzu Rodeo 2wd

should be on the driver's side under the dash

Posted on Oct 24, 2008

ghost4548
  • 776 Answers

SOURCE: 6pin valve body trannny to 4pin using 6pin's TCM

First of all, which component(s) are you replacing? Only the valve body? If so, then there's something different about the one you took out compared to the one you're putting in - that can be dangerous! BEST SOLUTION: Replace/Install in the correct part at the beginning.

Posted on Jun 02, 2009

emissionwiz
  • 76649 Answers

SOURCE: 4l30e transmission solenoid replacing 1-2

pull the trnasmission pan off, the solenoids are attached to the vlave body inside the trans.

Posted on Sep 19, 2009

Testimonial: "yeah this helps but do i pull the whole valve body down to replace "

  • 750 Answers

SOURCE: Holden rodeo 99 3.2v6 4l30e code 82 and going into limp mode

the tcm may be faulty or has a loose ground, try swaping in another if you can get one borrowed or a cheap used one from a salvage unit

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the shift solenoid located in a 2001 Isuzu' rodeo 3.1 liter and how many are their


it's located inside the bottom of the transmission pan You have to remove the pan to get at it and replace it.

Sep 13, 2016 | 2001 Isuzu Rodeo

1 Answer

I have a jaguar s type 2000 it writes gearbox fault and is in limp mode funny the fan is noisy to,please help


You must have a check engine light on in your dash. You first need to pull up the code. I will assume your trans is an automatic. If so, when your trans goes into limp mode, if you stop , shut off your motor, and start again, does your car run OK again, till the next time it goes into limp mode. If so you have a bad trans solenoid. Sometimes this solenoid is on the outside of a trans and sometimes it's on the inside. If inside you would have to drop the pan, and valve body, because it's on top of the valve body. The fan is a separate issue. GOOD LUCK FRIEND.

Nov 17, 2014 | Cars & Trucks

1 Answer

Hard shift low to second


In general-- a transmission that is failing

You can remove the valve body & clean it,
just keep in mind all the check balls fall out,
so you will need a diagram of it

After that-- you have to diagnose & replace any
shift solenoids that apply

Old vehicle & trans,I wouldn't change solenoids or
try adjusting bands, unless you have trans repair experience

Apr 08, 2014 | 1998 Dodge Dakota

1 Answer

How to remove the Valve Body on a 31th Transaxle 3 Speed


Drop the trans panfirst thing you see is the valve body there are several screws holding it on they may be torcks headed wiggle it some it should come right out

Apr 18, 2013 | 2000 Dodge Neon

2 Answers

My 97 tahoe will not go into reverse but good in all forward gears


Inside this type of transmission reverse is applied with a special clutch band, that band is usually the first thing to wear out in any automatic transmission, no reverse is a very common failure and I see it often on FixYa, the only solution is to overhaul the transmission, since replacing the reverse band requires the transmission be completely disassembled.

Jan 14, 2011 | 1997 Chevrolet Tahoe

2 Answers

My 1989 chevy blazer goes into neutral instead of third gear and overdrive. 1st and 2nd gear work fine. What could cause this? Is it my torque converter or transmission?


You could pull the trans pan and remove the valve body, and clean.

Not the converter,it is there to build pressure, to supply the valve body and apply fluid to clutch drums, that apply pressure on the clutches for each gear.

If you do remove the valve body to clean, you will need a picture of where the check balls go,when you replace it. Put assy trans lube or vasoline on balls to hold in place. Your working upside down unfortunately.

If the shift valves are free,no sediment, your out of options, unless a servo valve is hung up and doesn't apply a band. They out it comes,and you take it apart,to find the issues

Don't recall solenoids,other than for converter lock-up, back in 1989. Someone else may add to my theory.

Sep 16, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

I'm having some transmission problems


I am not an expert on trannys, but I know that the chevy 4L30E and the 4L60E have valve bodies in the bottom that are removable and they contain the shifting solenoids, A lot easier to replace than dropping the transmission. It will only fix the shifting, not the slipping, if you had any. I just bought 2 shift solenoids for mine, and I ma going to drop them in this weekend. I hope they work.

Apr 09, 2010 | 1996 Chevrolet Caprice

3 Answers

Where on the transmission -- is the shift solenoid located on the 2002 Isuzu Rodeo


It is located just under the pan in a block called the valve body, it contains 2 shift solenoids, and a million little canals for oil. There is no drain plug on it, just have to drop the pan and spill out the fluid, that drips for months afterward. You can change these things if you are handy, if not, don't even attempt it. Watch out for the check balls,

Jan 26, 2010 | 2002 Isuzu Rodeo

2 Answers

Holden rodeo 99 3.2v6 4l30e code 82 and going into limp mode


the tcm may be faulty or has a loose ground, try swaping in another if you can get one borrowed or a cheap used one from a salvage unit

Oct 30, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14379 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...