Question about 1996 Mercury Villager
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Timing Belt
I have used the Haynes Repair Manual for the Mercury Villager to change the timing belt on my 1993 Villager, twice. I just finished last night with the latest change. I found the Haynes manual to be very useful. This is just an overview:
1. Jack up the the van and support it on jack stands. Remove the front passenger side wheel and 2 plastic splash sheilds.
2. Remove the two radiator hoses on the passenger side of the engine.
3. Remove the pulley from the water pump (4x 10mm bolts)
4. Remove the tensioner pulley, including the bracket, for the A/C compressor. (3x 12 mm bolts)
This one can be difficult because it requires a torx head to loosen the pulley and it's a very tight fit to get a torx in there. I ended up taking the torx head out of the socket then turning it with a 10mm wrench.
5. Remove all 3 drive belts.
6. Remove the crankshaft pulley. (1-1/16" bolt) You will need a good strap wrench to keep the pulley from turning or an impact to remove this bolt. You may be able to remove the pulley just by bumping it with a mallet, but you may need a gear puller.
7. Remove the timing belt cover, it has an upper and lower half and is held in place by several 8mm screws.
8. You will find that the timing belt pulleys on the both cam shafts and the crank shaft have a white paint mark on one tooth. Make sure the marks on the two cam shaft pulleys are in line with a "bump" mark on the back plate of the belt cover. The bump mark for the front cam is located at about the 2 o'clock position and the one for the rear cam is at about the 10 o'clock position. You will need a mirror and flashlight to see this one.
The crankshaft pulley mark lines up with a notch in the oil pan (I think it's the oil pan where the notch is, but you will see it at near the 6 o'clock postion.
9. My new timing belt was a DAYCO and it came with a good instruction sheet. The new belt has an arrow that should point AWAY from the engine. There are also 3 lines on the new belt that will line up with the lines on the timing belt pulleys.
10. The belt tension should be adjusted so that you get about 0.5" - 0.6" of deflection at the center between the two cam shafts.
Note: I recommend replacing both the tensioning pulley and water pump while you are in there.
A water pump is about $32 and the tensioning pulley is about $35 but it's money well spent.
I did NOT replace the tensioner pulley the last time I changed the timing belt, and that is what failed this time. I could have saved myself a lot of work if I had replaced the pulley the first time.
Hope this helps. I'd still buy the HAYNES manual.
Posted on Dec 16, 2008
SOURCE: Belt question
You should clarify which engine it is, and you can look under the hood near the radiator for the serpentine belt instillation diagram that is on a sticker. Rick
Posted on Apr 16, 2009
Tips for a great answer:
Nov 18, 2014 | 2002 Mercury Villager
Nov 17, 2011 | Cars & Trucks
Jun 16, 2011 | Mercury Villager Cars & Trucks
Mar 29, 2011 | 1999 Mercury Villager
Nov 08, 2010 | 1998 Mercury Villager
Feb 26, 2010 | 1998 Mercury Villager
Jan 31, 2010 | 1996 Mercury Villager
May 06, 2009 | Mercury Villager Cars & Trucks
Dec 16, 2008 | 1999 Mercury Villager
24 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: