Question about 2001 Lincoln LS V8

Open Question

2001 lincoln LS v8 codes p0171, p0174; p1506

I already get a new MAF sensor, new oxygen sensor 1 bank 2 and and still getting those codes sometimes the car just turn off when put R or D, also sometimes the just leave a 1 white smoke cloud what shoudl i do?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jgwhomeequip
  • 1902 Answers

SOURCE: Codes P0171, and P0174 bLean on a 98 Navigator. Any ideas?

O171 MAF (Mass Airflow Sensor) Just try cleaning this part it usually solves that problem without having to buy new part.

0174 Both are mass air flow sensors. The other problem can be a vacuum leak Check PCV valave and all vacuum lines. Also make sure fuel filter and fuel pump are working correctly. You can clean the MAF with some brake cleaner make sure it is dry before you install it back

Posted on May 28, 2009

warlock61
  • 659 Answers

SOURCE: i got the codes from auto zone 4 codes came up

it could but most likely not check for a vacuum leak check the hoses to the throttlebody the rubber fittings have a tendancy to get soft and collapse

Posted on May 23, 2009

GasparMacari
  • 166 Answers

SOURCE: diagnostic code #'s p0174,p0171

oxygen sensors are telling you that the mixture is too poor on ur sistem need to check its behaviour and see whats causing that lean mixture
hoope this helps

Posted on Nov 10, 2009

  • 155 Answers

SOURCE: I'm getting a DTC of P0171 and P0174. System to lean bank 1 & 2.

your car is probably running rough
its sucking air from the intake mininfold
is your intake maninfold plastic? but your veicle is defenetly having a vaccum problem

Posted on May 10, 2010

  • 3 Answers

SOURCE: fault codes p0171 p0174

Same problem on my 2004 aviator, the problem was the rubber pcv boot, took it off and there was a hole in it.

Posted on May 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keeps throwing up trouble codes p1506,p1151,p0302,p0171


Definition of Diagnostic Trouble Code P1506 Audi: Closed Throttle Position Switch Does Not Open/Short to Ground BMW: Idle-Speed Control Valve Opening Solenoid Control Circuit Signal High Ford: Idle Air Control Overspeed Error (see P0507) Jaguar: Idle Air Control System RPM Lower Than Expected - B Bank Kia: IAC Valve Opening Coil Voltage High Lincoln: Idle Air Control Overspeed Error (see P0507) Mazda: Idle Air Control Overspeed Error Mercury: Idle Air Control Overspeed Error (see P0507) Porsche: Throttle Jacking Unit Lower Mechanical Stop, Signal Implausible Volkswagen: Closed Throttle Position Switch Does Not Open/Short to Ground Volvo: IAC Valve Opening Signal
------------------------
Definition of Diagnostic Trouble Code P1151 Audi: Bank1, Long Term Fuel Trim, Range 1 Leanness Lower Limit Exceeded BMW: Oxygen Sensor Heater Circuit Signal Intermittent (Bank 2 Sensor 1) Ford: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Jaguar: Lack of H02S-21 switch, sensor indicates lean Land Rover: Lambda control limit bank 2.Implausible signal/condition Lincoln: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Mazda: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Mercury: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Subaru: HO2S-12 Heater Circuit High Input Toyota: Coolant Path Clog Up for Coolant Heat Storage System Volkswagen: Bank1, Long Term Fuel Trim, Range 1 Leanness Lower Limit Exceeded
------------
Definition of Diagnostic Trouble Code P0302 Category: Powertrain Definition: Cylinder 2 Misfire DetectedNote: This definition of P0302 is applied to all manufacturers
--------------------------
Definition of Diagnostic Trouble Code P0171 Category: Powertrain Definition: System Too Lean Bank 1Note: This definition of P0171 is applied to all manufacturers

Jun 17, 2015 | Cars & Trucks

1 Answer

Chevy Silverado error p1151


P1151 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 2


p1131 p1151 p0171 p0174 p1131 p1151 p0171 p0174
All of these p1131 p1151 p0171 p0174 codes indicate a problem with a lean condition. This engine is known for vacuum leaks, so before you start throwing oxygen sensors at the problem, it pays to perform some diagnostics.
Start by cleaning the MAF sensor. Spray the sensor with CRC MAF sensor cleaner. Next, check the plastic vacuum lines, especially where they meet with rubber boots. If they are cracked or the rubber is swollen, replace the line. Then check the rubber elbow that holds the PCV valve. That elbow is a know failure point. In fact, the entire PCV tubing is a trouble spot on these engines. (thanks Ford).
After you've checked for vacuum leaks, check the operation of the oxygen sensors. The easiest way to do that is to disconnect the sensor from the harness. Connect one lead of your digital voltmeter to the black wire on the sensor and the other lead to battery negative. Then start the engine and add fuel (either propane, starting fluid, or carb cleaner) into the throttle body to force the mixture to rich. You should see a corresponding increase in voltage as you add fuel (from 0 volts to slightly less than 1 volt). Start and stop the fuel enrichment and watch the meter to see if the volts drop as you stop adding fuel. If you see no change, the sensor is dead. Replace it.
You can also use the fuel enrichment procedure to locate intake gasket leaks.
P1131 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 1
P1151P1151 Lack of Upstream Heated Oxygen Sensor Switch - Sensor Indicates Lean - Bank No. 2
P0174 system lean bank 2
P0171 system lean bank 1


This is the only info that didn't come back directly to FORD (yet still mentions it) instead of GM. Not to sure you got the correct code.

Jul 08, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

2002 lincoln ls diagnostic code P0174


Hi there:




Basically this means that an oxygen sensor in bank 2 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 2 is generally the side of the engine that doesn't have cylinder #1.


Note: This DTC is very similar to P0171, and in fact your vehicle may show both codes at the same time.


Symptoms
You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.




A code P0174 may mean that one or more of the following has happened:


The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
There could be a vacuum leak downstream of the MAF sensor.




Possible solutions include:


In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
Inspect all vacuum and PCV hoses, replace if necessary
Check for a dirty fuel filter and proper fuel pressure




Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

May 22, 2012 | 2002 Lincoln LS

1 Answer

I have a 2001 ford expedition that bogs out when i put it in drive but runs fine in second gear.


DTC P0171 - System Too Lean (Bank 1) and P0174 - System Too Lean (Bank 2)
Basically this means that an oxygen sensor in bank 1 or bank 2 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1. Bank 2 is generally the side of the engine that doesn't have cylinder #1.
Note: This DTC is very similar to P0174, and in fact your vehicle may show both codes at the same time.

You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.

A code P0171 may mean that one or more of the following has happened:
The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.There could be a vacuum leak downstream of the MAF sensor.

Possible solutions include:In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstallingInspect all vacuum and PCV hoses, replace if necessaryCheck for a dirty fuel filter and proper fuel pressure

DTC P0155 - 02 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)This code refers to the front oxygen sensor on Bank 2. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0155. See also: P0135 (Bank 1).


You will likely notice poor fuel economy the illumination of the MIL.

A code P0155 may mean that one or more of the following has happened:O2 Heater element resistance is high
Internal short or open in the heater elementO2 heater circuit wiring high resistanceopen or short to ground in the wiring harness

Possible SolutionsRepair short or open or high resistance in wiring harness or harness connectorsReplace oxygen sensor (cannot repair open or short that occurs internally to sensor)


DTC P0161 - Oxygen O2 Sensor Circuit Low Voltage (Bank 2, Sensor 2)It basically means the PCM detected either an excessive current draw, or an open or short in the circuit powering the oxygen sensor's heater circuit. This is in reference to the Heated Oxygen Sensor (2) located rear of catalytic converter (Bank 2).


There will likely be no obvious symptoms other than MIL illumination.


A code P0161 may mean that one or more of the following has happened:HO2S heater power circuit openHO2S heater ground circuit openHO2S signal tracking (due to oil or moisture in the connector)HO2S is damaged or has failed PCM has failed

Possible Solutions:Replace HO2 SensorRepair open or short in power circuitRepair open or short in ground circuitRepair damaged connector due to tracking

Hope helps.

Mar 27, 2012 | 2001 Ford Expedition

1 Answer

My lexus rx300 2001 is blowing white smoke and reading codes p0171 and p0174


Hi there:
P0171 - System Too Lean (Bank 1)
P0174 - System Too Lean (Bank 2)
Basically this means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.

Note: This DTC is very similar to P0174, and in fact your vehicle may show both codes at the same time.

You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.

A code P0171 or P0174 may mean that one or more of the following has happened:
The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
There could be a vacuum leak downstream of the MAF sensor.

Possible solutions include:
In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
Inspect all vacuum and PCV hoses, replace if necessary
Check for a dirty fuel filter and proper fuel pressure

Hope this helps.

Feb 22, 2012 | 2001 Lexus RX 300

1 Answer

What does the code 171 mean when you dionostic on your car


DTC P0171 - System Too Lean (Bank 1)
This means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.

Note: This DTC is very similar to P0174, and in fact your vehicle may show both codes at the same time.

You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.

A code P0171 may mean that one or more of the following has happened:
* The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
* There could be a vacuum leak downstream of the MAF sensor.

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa.

Nov 01, 2011 | 2000 Lincoln LS

1 Answer

Engine check light on error code 1 is P0171 system too lean bank 1 error code 2 is P0174 system too lean bank 2


P0171 system too lean bank 1
P0174 system too lean bank 2
links to information on the codes

it means that the O2 sensors in your vehicle detected a lean condition in their respective banks. this could be caused by a dirty MAF (mass air flow) sensor or a vacuum leak downstream from the MAF sensor

sometimes you can clean the MAF with electronics cleaner or brake cleaner but be sure to take it off the vehicle first. be careful not to damage the MAF while spraying the cleaner, and allow it to dry completely before installing it on the vehicle.

May 21, 2011 | 2001 Jaguar S-Type

2 Answers

Code 171 and 174 show up what are they


P0171 - System Too Lean (Bank 1)

Basically this means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.

Note: This DTC is very similar to P0174, and in fact your vehicle may show both codes at the same time.

Symptoms: You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.

Causes: A code P0171 may mean that one or more of the following has happened:
* The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
* There could be a vacuum leak downstream of the MAF sensor.

Possible solutions include:
* In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
* Inspect all vacuum and PCV hoses, replace if necessary
* Check for a dirty fuel filter and proper fuel pressure



P0174 - System Too Lean (Bank 2)

Basically this means that an oxygen sensor in bank 2 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 2 is generally the side of the engine that doesn't have cylinder #1.

Note: This DTC is very similar to P0171, and in fact your vehicle may show both codes at the same time.

Symptoms: You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.

Causes: A code P0174 may mean that one or more of the following has happened:
* The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
* There could be a vacuum leak downstream of the MAF sensor.

Possible solutions include:
* In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
* Inspect all vacuum and PCV hoses, replace if necessary
* Check for a dirty fuel filter and proper fuel pressure


Remember to rate and comment this. Hope helps.

Sep 21, 2010 | 2001 Ford Windstar

2 Answers

99blazer s10 trouble codes p171/p174


P0171 - System Too Lean (Bank 1)
Basically this means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.

A code P0171 may mean that one or more of the following has happened:
  • The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
  • There could be a vacuum leak downstream of the MAF sensor.
Possible solutions include:
  • In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
  • Inspect all vacuum and PCV hoses, replace if necessary
  • Check for a dirty fuel filter and proper fuel pressure

P0174 is identical to P0171, except it indicates the problem exists on Bank 2 as well.

Nov 22, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

Ford Windstar 1996 Trouble Codes P0171, P0141, P0161, and P0174


Bank one is toward the front of the vehicle. Sounds like the heated oxygen sensors have gone bad. The Oxygen Sensors are located in the exhaust pipe and require a special socket to remove and replace.

Jan 16, 2009 | 1996 Ford Windstar

Not finding what you are looking for?
2001 Lincoln LS V8 Logo

Related Topics:

470 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...