Question about 1995 Chevrolet Suburban

2 Answers

I have a 1995 Suburban that will not move in any gear. 2 wheel or 4wheel.

It first would not shift out of first, then added some fluid and it would shift to 2nd. Then when driving and testing it it would not move when I stopped at all. Then shut it off and it moved again, then did the same thing. Last time it moved I was in Drive and put it into reverse and it still went forward. So shut it off and now it will not move at all. Can see the cable moving when I shift, but the vehicle will not move in 2WD 4Hi or 4 Lo. Any solutions?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 12,104 Answers

Have trans diagnosed internal damage [ most likely damaged burnt out clutches ]

Posted on Jun 13, 2017

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,589 Answers

Replace your transmission.

Posted on Jun 13, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: while driving truck makes a humming sound in drive now no reverse

If you have no reverse then yes it needs to be rebuilt. as far as the whining it could be in one of the differentials. or in trans? just depends on where you hear it

Posted on Dec 08, 2008

  • 6 Answers

SOURCE: s10 pickup 4wheel drive wont shift from 4hi to 2hi

Mine is on the front drivers side, is yours? I just about fell over when I discovered who they designed it!

Posted on Jan 01, 2009

SOURCE: 1998 Chevy Blazer 4x4, $ wheel drive won't work (both 4hi & 4lo )

Reset the computer by disconnecting the battery. This should solve this. nutetral is for the four lo only to engage.

Mike

Posted on Feb 02, 2009

SOURCE: 98 Chevy S10 4wd drive will not engage when button is pushed

your problem sounds like either the transfer case control module located where you hear the clicking sound, or the actuator on the transfer case itself.

try unplugging the transfer case control module and then plug it back in, try engaging 4wd again (make sure your in neutral, coasting at 1-2 mph might help as well) if it still doesn't work check the actuator itself to see if the actuator is trying to engage. if the actuator is trying to engage but doesn't, take the actuator out and check it for wear or damage. if the actuator seems fine and it responds to the buttons when pressed i'd go after the transfer case control module as the culprit. ran into that a few times on those s-10's. 3 out of 4 that i've seen were fixed with a new tccm. 1 of the 4 needed an actuator, check your local junk yard for a working tccm or actuator.

hope this helps!

Posted on Feb 17, 2009

dennymulford
  • 1055 Answers

SOURCE: 98 K1500 suburban, can not engage 4wd, HI or Lo runs otherwise

your doing it right but your accuater is bad 59.00 auto zone easy install

Posted on Feb 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 explorer disengages 4wh low but does not engage 2wheel


Does it shift to 4wd high range ? If so then shift to 2wd . What is going on here is the transfer case motor is stopping due to the motor position sensor has gone bad which means that you replace the transfer case motor assembly. But if you wish to make it a 2wd for awhile then remove motor and manually turn shaft . This can be done by raising and supporting rear axle truck in park remove motor turn shaft slowly with pliers and rotating the play in drive shaft. There are stamped markings on back of case showing gear positions..

Mar 31, 2014 | 1996 Ford Explorer

1 Answer

Does the 4 wheel drive shifter need to be in neutral when driven out of 4 wheel drive. when i put it in neutral and put the normal shift gear in drive the vehicle will not move. but when i put the 4wheel...


4 wheel neutral vehicle will not move that for towing or moving around --put in 2wh --4hi or if have 4low transfer case has to be in a setting to move

Aug 29, 2017 | 1998 Toyota 4Runner

1 Answer

My 1994 Jeep Grand Cherokee Limited was running perfect and has alway been maintained suddenly it would not shift into gear it still has transmission fluid. help Rita


not sure but please check and make sure 4 wheel drive lever is not in neutral and its in 2or 4wheel drive. if its not engaged then jeep will not move. hope its this simple for you. hope this helps. keep on jeepin!

Jan 18, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Ive got a 2 wheel drive 85 gmc suburban 3/4ton with 454 and turbo 400. when i baught it there was a noise comin from tranny but only in first gear. it had no problems with shifting till i moved and towed a...


you can try flushing it using Seafome and replace your filter and fluid adding some trans tune with the new oil can git this things from most part stores . Hope this helps.

May 03, 2010 | 1985 GMC Suburban

1 Answer

4wheel drive on the fly...locked in 4 wheel drive


You must shift out of 4X4 with the truck in neutral while it's running.

Jan 07, 2010 | 2004 Ford F150

1 Answer

1995 k1500 suburban will shift into 4 wheel drive but then it jumps or bucks as you start to accelrate acts as if though it is not fully engaged. afraid it may damaged gears. any ideas?


My 95 did the same thing and it ended up being the Transfer case itself there was a missing tooth on a gear inside there.Jack the vehicle up and put it on stands remove the front drive line then spin each of the front tires if you don't hear any noise there then start working your way to the T-case,block the rear wheels very good and set the parking break put the vehicle in neutral and try to spin the output flange to the front axle listen for noises,if still nothing put the rear up on stands also and put it in 4wheel drive and trans in neutral spin rear drive line by hand and listen hopefully that helps to get you started in the right direction

Dec 26, 2009 | 1995 Chevrolet K1500

1 Answer

Gmc suburban 1500 4 wheel drive 1994 is sending a


code 28 is transmission range pressure switch, check the fluid level and get back to me, hope this helps. Please rate my fix as i strive to be the best Thanks Ray

Dec 10, 2009 | 1994 GMC Suburban

1 Answer

1995 grand cherokee trans not shifting in to second gear


Check transmission fluid levels,,replace lost fluid as needed,,,if this does not work,,take the car to a mechanic,,,sorry to say,,this kind of problem almost alway's requires a transmission mechanic to repair.

Jan 13, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Chevrolet Suburban Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...