Question about 2004 Ford F150

Open Question

Power steering reservoir hose location for 2004 f 150

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: air in power steering lines

trans fluid and p/s fluid same thing thats fine. Did you fill fluid first before starting vehicle? These pumps burn up easily if run dry.

Posted on Dec 16, 2008

fknstart
  • 404 Answers

SOURCE: replace power steering hoses

trace the filler or resiviour clean and run to find leak one side is high pressure so dont mix up,it may hv have 0 rings so renew.when fitted refill filler run and refill as it will go down

Posted on Jan 06, 2009

jeremythious
  • 37 Answers

SOURCE: loose hose power steering ford escape 2004

Tighten it.

Posted on Feb 07, 2009

  • 8 Answers

SOURCE: power steering

Probably not just follow the lines from the pump to the rack. If there is one it will be towards the grill area either to the side or in front of the radiator.

Posted on May 25, 2009

  • 1857 Answers

SOURCE: 1996 F-150 Eddie Bauer edition 6cyl-2WD, every now

the pressure valve in the power steering unit is faulty. Replace the power sterring pump

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Anybody know how to locate the power steering reservoir on a 2015 S350d. Searched the whole engine compartment without any luck


If the car actually has a power steering reservoir the location will be found in the vehicle handbook.

The conventional PAS with a reservoir mounted on or near the engine driven pump is in decline and is being replaced by electro-hydraulic systems with the electrically driven pump and integrated reservoir mounted on or near the steering rack and pure electrical systems are also increasing in popularity due to the ease of electronic monitoring and control.
These latter systems tend to be integrated into the steering column.

If there is an engine driven pump there will be a reservoir and you find it by following the pipes/hoses if the usual method fails.

Jun 18, 2017 | Cars & Trucks

1 Answer

How to replace suction and return hoses on power steering reservoir


How-to: Replacing the power steering reservoir to pump hose - CEG ...

contour.org/.../82138-how-to-replacing-the-power-steering-reservoir-to-...
Jul 3, 2013 - How-to: Replacing the power steering reservoir to pump hose ... to allow air into the suction side of the PS pump, aerating the fluid. ... off the spring hoseclamps from the smaller return hose and the large hose to the pump.
images for How to replace suction and return hoses

Dec 01, 2015 | Cars & Trucks

1 Answer

The location of the power steering pressure hose


i am attaching an image of the power steering reservoir, the hose that comes after the power steering pump is the side of which there is pressure(that is the power steering pressure hose) the hose that is connected directly to the reservoir is the return hose .
25850762-rtaxqpr0oaky0aaugk2xzgrt-1-0.jpg

Sep 05, 2015 | 2000 BMW 528i

1 Answer

Wheres power steering pump located on 1997 ford contour,the power steering stoped working


POWER STEERING PUMP IS BELT DRIVEN PUMP LOCATED NEAR TOP ENGINE.LOOK FOR PUMP THAT HAS A RESERVOIR AND A CAP THAT READS POWER STEERING FLUID ONLY ALSO POWER STEERING PUMP HAS TWO POWER STEERING HOSE CONNECT TO RACK AND PINION.

Mar 12, 2011 | Ford Contour Cars & Trucks

2 Answers

Where is the power steering dipstick


Most power steering pumps are driven by the serpentine belt and should be in plain view when the hood is open.The following shows how to remove and replace the power steering pump and might give you a clue if not in plain sight. My dad's 1998 Ford Taurus has it nearly on top, but they could have changed things in the mean time: Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.
Power steering pump special tools ford-08-00-401.gif

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.
Power Steering Pump (4V) and SHO To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump. Disconnect the power steering pump reservoir hose and allow it to drain.
  6. Using Pulley Remover T69L-10300-B, or equivalent, remove the pulley from the power steering pump shaft.
  7. Disconnect the pressure hose from the power steering pump and allow it to drain.
  8. Remove the power steering pump retaining bolts and the pump.
To Install:
  1. Install the power steering pump and tighten the bolts 15–22 ft. lbs. (20–30 Nm).
  2. Connect the pressure hose and secure the clamp.
  3. Using a Steering Pump Pulley Replacer T65P-3A733-C, or equivalent, install the power steering pump pulley: the pulley face must be flush with the pump shaft or within 0.010 inch (0.25mm).
  4. Connect the power steering pump reservoir hose.
  5. Install the radiator coolant recovery reservoir.
  6. Install the accessory drive belt.
  7. Fill the power steering reservoir with power steering fluid.
  8. Connect the battery ground cable.
  9. Start the engine and check for leaks and proper operation. Bleed the power steering system if needed.
prev.gif next.gif

Jul 22, 2010 | 1996 Ford Taurus

1 Answer

How do i flush the hydraulic steering system


You really can't flush out the steering system fluid other then siphoning the fluid out of the steering pump reservoir. This is the easy way.
The hard way:
Remove the filler cap from the top of your power steering system then disconnect the reservoir's hose. It should be located on the bottom of the reservoir. The hose can be tough to remove, so make sure you have plenty of patience.

Replace the reservoir's hose with another hose. It should lead to an empty container. You'll use this container to store the old power steering fluid as it leaves the reservoir. Lift the front end of your car off the ground by using a car jack.

Add new power steering fluid to the reservoir. As you add the new lubricant, it will force the old lubricant into the tube you've connected to the bottom of the reservoir.

Climb into the drivers seat and rack your steering wheel back and forth. The wheel should be locked in place, allowing only a slight range of mobility. This will help the extra lubricant within the power steering system to drain.

Watch the empty container. It should fill with old lubricant. Once the old lubricant has been flushed and you see clean fluid replacing it, you've finished the hard part.

Disconnect your hose and move the container. Replace the original reservoir hose. Pour new, clean power steering fluid into the reservoir. Rack your steering wheel a few more times to squeeze out air that might be trapped in the lines. Replace the filer cap and close your done.

Thank you for suing fixya and good luck







Jun 11, 2010 | 1993 Chevrolet Camaro

1 Answer

Where is the thermostat located between top


On 1998, 4.6 32 valve engines, the thermostat is located in the radiator to block hose. if you look directly under the power steering reservoir you should see it.

The thermostat has 3 hoses running from it. 2 are approx. 1.5" in dia. and one is approx .750" in dia. The .750" hose leads up to the coolant reservoir. and yes it is under the power steering reservoir. Access to the thermostat is from the bottom side. You will need an 8mm socket to remove the two bolts. Removal of the bottom radiator hose is mandatory.

Hope helps with this (remmeber rated this help).

Mar 08, 2010 | 1998 Lincoln Mark VIII

1 Answer

Location of Power Steering Reservoir


As far as I remember, the reservoir is part of the pump But...If it's not there it is easy to find...there are two hoses on the pump...one leads to the steering box mounted to the frame, the other goes to the reservoir, then to the steering box.

Aug 20, 2009 | 1989 Jeep Wrangler

1 Answer

Need to locate power steering pump for 1996 buick


The power steering reservoir will be on the left side (near the passenger front wheel) behind the coolant reservoir. It's a black tank with orange lettering on the cap. If you follow the hoses off of it, they'll lead you directly to the pump.

Apr 13, 2009 | 1996 Buick Roadmaster

1 Answer

Where is the thermostat located on a 1997 lincoln mark 8?


thermostat is located in the radiator to block hose. if you look directly under the power steering reservoir you should see it.
The thermostat has 3 hoses running from it. 2 are approx. 1.5" in dia and 1 is approx .750" in dia. The .750" hose leads up to the coolant reservoir. and yes it is under the power steering reservoir

Mar 28, 2009 | 1997 Lincoln Mark VIII

Not finding what you are looking for?
2004 Ford F150 Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...