Question about 1993 Ford Thunderbird

1 Answer

CANT GET OLD IGNITION SWITCH OUT TO INSTALL NEW ONE.

I CANT SEEM TO GET THE OLD IGNITION SWITCH OUT OF THE COLUMN HOUSING.no KEY TO TURN TO ACC OR ON. PRESSING SMALL PIN ON TUMBLER BODY.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

Disconnect battery, then remove steering wheel. If you look in Haynes book in chapter 12 it gives you a good description. You will need special tool to remove and install switch. If you are talking about the lockworks, it is the same process.

Posted on Oct 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the ignition cylinder on my 2002 Toyota Rav 4 without the key?


from another post, psoted by James Allmond

How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

source

How do remove the ignition cylinder on my 2002 Toyota Rav 4 without the key

Jul 28, 2016 | Toyota Cars & Trucks

1 Answer

Trying remove the ignition in toyota avalon 2000


TO REMOVE THE IGNITION SWITCH FIRST TURN OFF RADIO.AND DISABLE AIRBAGS BY DISCONNECTING NEGATIVE BATTERY CABLE WAITING 20 MINUTES UNTIL AIRBAGS DISCHARGE.TO REMOVE IGNITION SWITCH PLACE THE IGNITION KEY IN THE ACC POSITION. REMOVE THE STEERING WHEEL AND REMOVE THE STEERING COLUMN COVERS.DISCONNECT THE IGNTION SWITCH ELECTRICAL CONNECTORS.REMOVE THE SWITCH RETAINING SCREWS THEN PULL THE SWITCH FROM THE LOCK CYLINDER HOUSING.IF YOU TRYING TO REMOVE THE LOCK CYLINDER WITH LOCK CYLINDER IN ACC POSITION. USE A SMALL SCREW DRIVER OR PUNCH. DEPRESS THE LOCK CYLINDER RETAINING PIN THEN REMOVE LOCK CYLINDER. TO INSTALL NEW LOCK CYLINDER. DEPRESS THE RETAINING PIN AND GUIDE THE LOCK CYLINDER INTO THE HOUSING UNTIL THE RETAINING PIN EXTENDS ITSELF BACK INTO THE LOCATING HOLE IN THE HOUSING.

Mar 01, 2011 | 2000 Toyota Avalon

1 Answer

I have a 1978 Chevy k-10 and the ignition switch in the column wouldn't turn off. We bought a new ignition switch and the old one will not come out of the column. There is no retaining screw holding it in...


It sounds as though you are talking about key tumbler in column and if you are then stick key in and turn back to acc. position should come out. if it is ignition switch on top of column then turn key until dash lughts come on. and remoce switch.

Feb 19, 2011 | Chevrolet C1500 Cars & Trucks

1 Answer

How to replace ignaction cylander


Hello, Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota.

  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTION: Some models covered by this guide may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
TO INSTALL:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.
Thanks

Aug 12, 2010 | 1989 Toyota Camry

1 Answer

How to Remove an Ignition Cylinder From a Toyota Camry 1994


prev.gif next.gif Ignition Lock/Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle. CAUTION
    Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
  2. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  3. Remove the screws which secure the upper and lower halves of the steering column cover.
  4. Turn the lock cylinder to the ACC position with the ignition key.
  5. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.). NOTE: On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  6. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  7. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing. To install:
  8. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  9. Secure the switch with its screw(s).
  10. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  11. Install the steering column covers and connect the ignition switch wiring.
  12. Connect the negative battery cable.
prev.gif next.gif

Jul 17, 2010 | 1994 Toyota Camry

2 Answers

I need to take out old ignition lock cylinder without key on 1989 toyota camry le -lost keys-bought locksmart replacement but it says old has to be in acc position to remove-


This is what the tech manual says.....

Ignition Lock/Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle. CAUTION
    Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
  2. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  3. Remove the screws which secure the upper and lower halves of the steering column cover.
  4. Turn the lock cylinder to the ACC position with the ignition key.
  5. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.). NOTE: On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  6. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  7. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing. To install:
  8. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  9. Secure the switch with its screw(s).
  10. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  11. Install the steering column covers and connect the ignition switch wiring.
  12. Connect the negative battery cable.

Jul 26, 2009 | 1991 Lincoln Town Car

1 Answer

My key will start the car but it wont turn the car off i have to unplulg the distributor to kill theh car. Also the ignition switch in the car rotates all the way around but it has always done that it just...


the ignition switch is an electrical part. The lock cylinder is whre the key goes and it activates the ignition switch. If you pulled the lock cylinder out, you could operate the car with a screwdriver.
Either you have damaged the ignition switch where the lock cylinder goes into it, or the lock cylinder is damaged where it fits into the ignition switch.

this is 96 taurus, don't have 92 sorry

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.
------------------
Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Ignition Switch The ignition switch (11572), which is mounted on the steering actuator housing (3F723), operates in the following manner:
  • The ignition switch is cycled through rotation of the ignition switch lock cylinder (11582) through a pin which is part of the ignition switch.
  • The ignition switch lock cylinder also controls the mechanism which provides a positive lock for the transaxle linkage and the steering system.
  • The locking mechanism is located in the steering column housing.
The ignition switch lock cylinder positions are:
  • ACC
  • LOCK
  • OFF
  • RUN
  • START
The key can be removed from the ignition switch lock cylinder with the column-shift transaxle only when the shift lever is in PARK position and the key is in LOCK position.
  • The ACC position operates while the steering and transaxle remain locked.
  • The engine shuts off when the key is turned to the OFF position without locking the steering or transaxle.
Blade Type
The ignition switch has blade-type terminals that engage with one multiple connector. The multiple connector is secured to the ignition switch by an integral connector fastener.

May 05, 2009 | 1992 Mercury Sable

1 Answer

Car was stolen broke the ignition


REMOVAL

  1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. On all models, disconnect battery ground cable.
  3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
  4. Remove key light case from lock body, if equipped.
  5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
  6. On except 1989 Accord, place ignition lock in the I position.
  7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.
INSTALLATION

  1. On 1989 Accord models, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the LOCK position.
    2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. On except 1989 Accord, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the O position.
    2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. Install ignition switch and connect battery ground cable.
SRS wire harness is routed near the ignition switch.

CAUTION:
  • All SRS electrical wiring harnesses are covered with yellow outer insulation.
  • Before disconnecting the SRS wire harness, install the short connector on the airbag.
  • Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
IGNITION SWITCH
  1. Remove the steering wheel, then remove the steering column covers.
  2. Disconnect the 7-P connector from the under-dash fuse box.
  3. Insert the key and turn it to "0."
  4. Remove the 2 screws and replace the base of the switch.

Feb 13, 2009 | 1992 Honda Accord

1 Answer

How to remove ignition cylinder from Toyota Camry 1993


Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Nov 23, 2008 | 1993 Toyota Camry V6

Not finding what you are looking for?
1993 Ford Thunderbird Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...