Question about Cars & Trucks

1 Answer

Seat ibiza cylinder head torque settings

Hi. Can anybody give me the torque wrench settings for the cylinder head on a 1998 seat ibiza 1.4 APQ engine.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,117 Answers

I am sorry we have info on all USA models and some common eurozone models like VW, Audi etc. This is not a common make and we have no info on it. Sorry

Posted on Feb 19, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

sirgabe51
  • 66 Answers

SOURCE: I have 4.9L6 need torque specs for cylinder head

for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Torque setting on cylinder head bolts


Hi require engine code ,make and model

Apr 05, 2015 | Cars & Trucks

2 Answers

Citreon xsara 1999 1.8 16 valve cylinder head torque settings


If yours is an Xu series engine, you need to use a torque wrench and an angle dial wrench. Tightening is in 3 stages.
  • Stage 1: Tighten up to 60Nm (44 lb/ft) then fully loosen
  • Stage 2: Tighten up to 20Nm (15lb/ft) change to angle dial wrench
  • Stage 3: Angle tighten to 300 deg.
To avoid confusion, do stage 3 in 3 steps, tighten 100 deg each round and repeating the cycle until 3 rounds.

07718717-6a90-48f5-a87c-bc1ff81d67bd.jpg

04a9b611-4f0b-4da6-9052-a1cb2e517c02.jpg

Jun 13, 2014 | 1998 Citroen Xsara 1.6

1 Answer

Torque specification


Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
- Install the plate washer to each cylinder head
bolt.
- Using Torque wrench, install and uniformly tighten the ten
cylinder head bolts in several passes.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)

Jan 26, 2014 | 1993 Toyota Corolla

1 Answer

Ibiza overheating


Depending on engine type check the temperature sensor on the cylinder head but without knowing the engine type ?? as earlier models had a switch in the radiator .

Dec 09, 2012 | 2000 Seat Ibiza

1 Answer

TORQUE SETTINGS FOR 1.4 16V 04 VAG ENGINE THEY USED IN SEAT LEON 04 16V 1.4.


Cylinder head instructions

Tightening sequence
tdisline_536.jpg
Cylinder head torque setting for 2004 VW 1.4L 16V fitted in Seat Leon
Renew bolts

Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

May 17, 2011 | 2000 Volkswagen Golf

1 Answer

Hi i'm eduardo and i have a '94 nissan pathfinder 4wd...engine 3.0.... i want to know the head torque specifications .


Hi Eduardo:
Check this information (click over pics for zoom)...

zjlimited_1062.jpg

Fig. 20: Exploded view of the cylinder head assembly-VG30E engine


zjlimited_1063.jpg

Fig. 15: Cylinder head loosening sequence-VG30i and VG30E engines


zjlimited_1064.jpg

Fig. 17: Cylinder head torque sequence-VG30i and VG30E engines


Install the cylinder head with a new gasket. Apply clean engine oil to the bolt threads and seats, then install the bolts with washers (beveled edges up) in the correct position. Note that bolts 4, 5, 12 and 13 measure 5.00 in. (127mm), and are longer than the others. The other bolts are 4.17 in. (106mm) long.

Tighten the bolts in the proper sequence, in the following stages:
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 43 ft. lbs. (59 Nm).
Loosen all bolts completely.
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 40-47 ft. lbs. (54-64 Nm). Or, if you have an angle torque wrench available, tighten them an additional 60-65 degrees.


Hope this helps; remember to rate this answer. Good luck.

Apr 22, 2011 | Nissan Pathfinder Cars & Trucks

1 Answer

We need the cylinder head torque specks for a 2.4 liter engine on a 98 plymouth breeze


f866f0c.jpg

Fig. 1: Cylinder head bolt tightening sequence-2.0L SOHC engine



f8b64c8.jpg

Fig. 2: Cylinder head bolt tightening sequence-2.0L and 2.4L DOHC engines

Tighten the bolts in 4 steps as follows:
a. First: all bolts to 25 ft. lbs. (34 Nm).

b. Second: all bolts to 50 ft. lbs. (68 Nm).

c. Third: all bolts again to 50 ft. lbs. (68 Nm).
d. Fourth: all bolts an additional 1 / 4 turn.

Do not use a torque wrench for the fourth step.


Hope helps (remember to rate and comment this).

Oct 22, 2010 | 1998 Plymouth Breeze

1 Answer

How to replace head gasket 1998 Lumina


Cylinder Head Removal & Installation 3.1L Engine To Remove:
NOTE: With some minor variations, this procedure can be used on both the left and right cylinder heads.
  1. Raise and safely support the vehicle.
  2. Drain the engine coolant and the engine oil. Lower the vehicle.
  3. Remove the upper and lower intake manifolds.
  4. Remove the rocker arms and pushrods.
  5. Remove the exhaust crossover pipe.
  6. Remove the engine mount strut bracket.
  7. If removing the left side (front) head, remove the dipstick tube.
  8. Tag for identification, then remove the spark plug wires.
  9. Remove the spark plugs.
  10. Remove the exhaust manifold using the procedures found in this section.
  11. Remove the eight cylinder head bolts, then remove the cylinder head. There are locator pins that align the head to the block. Pull upwards on the head to disengage the pins, then remove the cylinder head to a suitable work area.
  12. If the head is be overhauled, remove any remaining components such as the engine lift hook, the fuel line bracket bolts, the engine coolant temperature sensor, etc., as required.
Position a new gasket, install the head, then tighten the bolts in the sequence shown (3.1L engine shown) 93173g43.gif

To Install:
NOTE: If the head gasket failed, determine the cause. Gasket failure is caused by the following conditions: improper installation; overheating due to a failure in the electric cooling fan system or a leak in the cooling system; loose or warped cylinder head; missing, off location or not fully seated locator dowel pins; low torque on the cylinder head bolts; warped block surface; scratched or gouged gasket surfaces; excessive intake manifold torque and even cracked engine block tapped holes.
  1. Clean all parts well. Remove all foreign material to the bare metal. Do not use a motorized wire brush on any gasket sealing surface. It is good practice to use the proper size thread-cutting tap to clean the threaded bolt holes in the block. This helps assure an accurate torque reading.
  2. Place a new head gasket on the clean engine block deck surface. Many gaskets will have some sort of marking denoting TOP or THIS SIDE UP. Make sure the gasket sits flat and is not hung up on the locator dowel pins. Use no sealer on the head gasket.
  3. Carefully set the cylinder head in place, using care not to damage the gasket. Make certain that the head engages the locator dowel pins that properly position the head.
  4. The bolts should be very clean since dirt built-up on the bolt threads makes it difficult to get an accurate torque reading. These are 'torque to yield' bolts which stretch a small amount when tightened; new bolts are always recommended. On a used vehicle, especially a high-mileage vehicle, it may be difficult to determine if the heads have been removed before and how many cycles the bolts have been removed and tightened. New bolts should be part of any cylinder head service. Use GM Sealer #1052080, or equivalent, on the threads of the head bolts and install all eight bolts, finger-tight.
  5. With an accurate torque wrench, tighten the bolts gradually, in sequence, working from the center outwards. Final torque should be 33 ft. lbs. (45 Nm), plus an additional 90 degrees (1/4-turn). A torque angle meter is recommended.
  6. Install the remaining components in the reverse order of the removal process.

Aug 11, 2010 | 1998 Chevrolet Lumina

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

728 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...