Question about 1992 Chrysler Lebaron

1 Answer

Can not set timing on my 1992 lebaron 3.0

The timing moves all over, like from 12 before to 12 after just jumps around

Posted by on

  • James McMahon
    James McMahon Feb 20, 2012

    its not that i dont know how to set timming, its that the timming jumps all over, its not steady. when you try top set it, its going from 12 btdc to 12 atdc, something is causing it to move if it was a older car its like the Vacume adv is messed up,

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 5,763 Answers

First make sure all heat , light are off, start the engine and allow to reach operating temp,dissconnect coolant sensor wire, the radiator fans should come on and the check engine light will come on,check timing mark on crankshaft pulley, if it 2 degrees within specs leave it alone. if not then loosen distributor hold down bolt and adjust. the specs are 12 degrees btdc (before top dead center). recheck after you tighten hold down bolt then recoonect coolant sensor and clear check engine light. good day

Posted on Feb 19, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
saailer
  • 1868 Answers

SOURCE: ignition switch 1992 Lebaron

Hello! Disconnect +battery cable...Remove tilt lever...Remove 3 Torx column cover attaching screws...Then the upper and lower column column covers...Using a Torx with a security tip (also called tamper proof tip) #440-tx20H... Remove 3 ignition switch mounting screws...Carefully pull switch away from column...Release 2 connector locks on 7 terminal wiring connector...Then disconnect from ignition switch...Release connection lock on 4 terminal connector...Then disconnect from ignition switch.

Guru..................saailer

Posted on Jan 12, 2010

motor1258
  • 6674 Answers

SOURCE: 1992 Chrsler LeBaron. Lack of acceleration from

Code 12 is just telling you the battery has been disconnected, and computer reset when this happens. Did this happen suddenly or over time just gradually got slower? How does it run at highway speeds? When was last tune-up, throttle body cleaned, fuel filter changed, air cleaner etc? What engine and current mileage? All these answers will help us help you.

Posted on Sep 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set timing on 1994 chrysler labaron 3.0


the valve springs are pushing against the cam lobes and turning the cam, you have to hold them with special tools or wrenches, usually the will stay in time if you hold them lined up with the marks and release gently on wrench, don't breath or they will jump

25005933-iv5yhqpktypbvunjtpsp2olz-4-0.gif

Aug 25, 2014 | 1994 Chrysler LeBaron

1 Answer

Lebaron trunk doesn't stay up


There are rods that hold open the trunk they look like a small piston. They get weak over time and will not hold open trunk lid. You can buy them at any auto parts store. Hope this helps

Mar 12, 2014 | 1992 Chrysler Lebaron

1 Answer

1992 Chrsler LeBaron. Lack of acceleration from dead stop. I get error code 12 from diagnostics.


Code 12 is just telling you the battery has been disconnected, and computer reset when this happens. Did this happen suddenly or over time just gradually got slower? How does it run at highway speeds? When was last tune-up, throttle body cleaned, fuel filter changed, air cleaner etc? What engine and current mileage? All these answers will help us help you.

Sep 22, 2011 | 1992 Chrysler Lebaron

1 Answer

What rod or screw or nut to turn to adjust front end alignment? on 1992 lebaron? what needs to be removed? ball joint, rubber boot. What tools are needed to do it yourself? vise-grips, open-end wrench.


going by your question i`d say you don`t have the ability to perform this job yourself.to just adjust the front end alignment you don`t need to remove any components.you do need an alignment machine to get the angles set to specs,there are 3 angles that need to be checked,castor camber and toe-in otherwise your tires will wear and the car won`t go down the road straight.

May 03, 2011 | 1992 Chrysler Lebaron

1 Answer

How difficult to replace timing belt on 92 Lebaron, and appx labor cost?


about 3 to 6 hours 270 up to 900 deppening where u go im in ca

Apr 26, 2010 | 1992 Chrysler Lebaron

1 Answer

How can i check the code for the check engine light without using a meter. I hear there is a way to check the number of times the check engine light blinks with a manual procedure. I have the codes just...


Turn the ignition switch on off on off on off on. After the third time the check engine light should start blinking codes. It will start with 12. That is the start of codes code. It will end with 55. That is the end of codes code. You just want to know what codes are inbetween 12 and 55

Apr 08, 2010 | 1992 Chrysler Lebaron

1 Answer

Where is the flasher for the turn & hazard signals located on 1992 Lebaron LE V6 ?


You need to remove the glove box and have a look around the middle of the dash for a relay and flasher panel,way easier to find if you look it up in the owners manual but still it in there,why no one knows.

Dec 08, 2009 | 1992 Chrysler Lebaron

3 Answers

I need a serpentine belt diagram for a 1992 chrysler lebaron 3.0 liter v6


1992 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Serpentine Belt Diagram Alt., P.S., Idler & Tens.

669b86a.jpg

More details you can find in DAYCO Catalog

I hope help you whit this (remember rated this help) Good weekend.

Oct 02, 2009 | 1989 Chrysler LeBaron

1 Answer

Shifting


It may be time for a tranny service. They will change the filter, fluid, etc, and check it out. Better than having to buy another tranny if this one has a fixible problem.

Mar 28, 2009 | 1992 Chrysler Lebaron

1 Answer

Need to replace the hood on 1992 lebaron will a 1993 hood work?


Try your local junkyard usually you can find them for around $50-$100

Dec 17, 2008 | 1992 Chrysler Lebaron

Not finding what you are looking for?
1992 Chrysler Lebaron Logo

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...