Question about 2004 Hyundai Santa Fe

1 Answer

Renew throttle senser

How to fit

Posted by on

  • yadayada
    yadayada Feb 19, 2012

    Do you mean TPS switch

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 5,763 Answers

You will see a small arm where the sensor goes into thortlebody, use your hand to open the throtle to see which way arm moves, you will look at sensor rear and see that arm, use a screwdriver to see how it moves and springs back. you want that arm on throtlebody to go on with tension. so get hole close then push on and turn to line hole up, this way there a small movement of sensor.

Posted on Feb 20, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 toyota 22re misses at idle


think its time to remove the head and renew the gasket ,also remove the valves and renew the seals and gring them in a bit ,maybe even renew the valve springs ,or buy a newer vehicle as its nearly 20 yrs old

Nov 16, 2013 | 1994 Toyota Pickup

1 Answer

Engine runs poorly


clean the fuel injectors

Jun 24, 2017 | 1995 Volkswagen Golf

1 Answer

Why is there water in the mass air flow senser area?


how much water ?? is it not condensation. dry it off and try again

Nov 17, 2011 | 1998 Ford Windstar

1 Answer

Yukon 2003 do not acelerate I just set a used motor on my yukon and it crancks but do not acelerate. is the same if I give gas. (It has electronis throttle boby)


Could be a number of things but first make sure you throttle positioning senser is connected as well as you mep senser and egr

Oct 24, 2011 | 2003 GMC Yukon XL

1 Answer

1994 Osmobile Silhuette 3800 loss of power when accelerating , ok at normal speeds. Spudders and powerless going uphill and take off changed air filter, had gas tank cleand out and filter replaced. I...


The age of your vehicle guarantee's a vacuum leak. It may sound silly but the truth is rubber grommets and hose's shrink and dry out over time and the harsh environment under the hood makes it worse. Check all vacuum lines and fittings attached to the intake manifold, valve covers(pcv valve), and be sure to check for a vacuum fitting on top of the intake just behind the throttle body. Does it fit tight in the hole? You can seal loose fittings with a high-temp RTV (Red) silicone sealant/adhesive.

Have you hooked a scanner to the computer and checked the oxygen sensor(s)? If they are bad they could lean out the engine.

Also, a restricted exhaust system can lower engine performance. If you dont know old the plugs and wires are, replace them. With plug wires, its the age not the miles. How old is the coil pack? It could be "breaking down" at higher rpm's. Does your engine have a cam sensor? It would be located where a Distributer used to be on older engines.

Remember an engine needs three things to work properly...Air / Fuel / Ignition(Spark)

MAF sensor if bad, the engine may not even start let alone run.
MAP sensor on most Olds engines is located just behind the rear valve cover. It may have a 3 or 4 wire plug connected and a vacuum line. Its about 1 1/2 inches tall X 4 inches long X 3/4 inch thick.
Hope this helps and good luck!

Aug 10, 2011 | 1994 Oldsmobile Silhouette

1 Answer

Need to know were the MAP SENSOR is located on the a 97' nissan king cab 2.4L


Doesn't have one it does have a mass airflow senser and it's in the air intake hose on top of the air filter box. If the hose to the throttle body leaks in any kind of way ( attached hoses off or leaking cracked hose your gat Map codes the the airflow senser isn't getting full flow and theirs a problem that needs corrected check everything before changing the senser though as it's expensive and the senser is'nt returnable if your wrong.

Jan 28, 2011 | Nissan Pickup Cars & Trucks

1 Answer

92 corolla manual idles up and down while in neutral and engine temp increases to the max.Radiator is cold


Try replaceing the engine temperature senser,it may cure both problems.If it does'nt fix the surging the try a throttle position senser.

Nov 16, 2009 | Toyota Corolla Cars & Trucks

1 Answer

1993 toyota 4x4 idle problem


sounds like your throttle positioning sensor is not set right so i would undo the two phillips heads that hold it and turn it till the idle doesnt fluctuate should be turned most of the way to the front of the truck. Also check your idle screw that throttle body could be set different.

Jun 24, 2009 | 1993 Toyota Pickup

2 Answers

89 z24 chevy caviler


Hi,did you replace the engine computer(ecm)?

Aug 13, 2008 | 1989 Chevrolet Cavalier

Not finding what you are looking for?
2004 Hyundai Santa Fe Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...