Question about 2007 GMC Yukon XL Denali

1 Answer

Remote key entry dont work 2007 gmc yukon il - 2007 GMC Yukon XL Denali

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 5,763 Answers

This is a tough one without testing but i can say that 90% of the time its due to bad remotes. first make sure the battery in the remote is good, if you have another remote try that one and also make sure it has a good battery. i have seen spare remotes go bad also. the best thing is that if both remotes dont work then buy a new remote and try that.

Posted on Feb 19, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2007 gmc yukon denali wont unlock w/ keyfob

Check the buttons.. I have an 06 Grand Prix with the Remote starter on the top and it seems that the conductor on the buttons worn out.. Take the keyfob apart, pull the rubber buttons off the chip, lick your finger and touch the place where the unlock (right side of the fob) would be. That should unlock your doors. I just did it with mine. I would just buy another fob on ebay and change the buttons out.. Hope this works

Posted on May 24, 2010

alicantecoli
  • 22246 Answers

SOURCE: My 2007 GMC Yukon has locked itself 3X once with

locks have so many key positions but on a popular vehicle this can happen where they have the same key indentations ,but yopu friend couldnt start your car as it has a chipped key ,but years ago in the car rental we had two fiat puntos parked in the same car park in torrevieja and they got taken by the wrong persons so we had to drive around and find the houses and get the cars back and swop them over .but this was before chipped keys ,also had it with two ford fiestas in benidorm as well

Posted on Jul 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I HAVE A 2007 GMC YUKON SLT AND ALL THE BUTTONS WORK EXCEPT FOR REMOTE START


if the body control module is seeing any door or hood not completly closed it will not start.

Feb 17, 2013 | 2007 GMC Yukon Denali

1 Answer

Remote does not work on my 2007 GMC Yukon. I changed battery and I used spare remote, but no response. After I drive the vehicle, the remote will work, but after I few minutes, it goes back to not working.


{: ) Try to reprogram your remote transmitter again. If you have two or more remote transmitters, they should be programmed at the same time (in one session only). Otherwise you may need to replace and reprogram your remote control receiver.

Apr 27, 2011 | 2007 GMC Yukon Denali

1 Answer

Yes i have a 2007 gmc yukon denali. when i bought it they didnt give me the keyless entry pad with remote start, then when they did give me one it wasnt the one for my vehicle, they told me all i had to do...


Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation

Feb 11, 2011 | 2007 GMC Yukon Denali

1 Answer

2007 gmc yukon. Keyless Entry problem. The remote quit working but the gmc place said its not the battery. Help


Disconnect the battery to the car for five mins. Thay should reset the keyless module. I had the same problem

May 20, 2010 | Cars & Trucks

1 Answer

2007 gmc yukon denali wont unlock w/ keyfob


Check the buttons.. I have an 06 Grand Prix with the Remote starter on the top and it seems that the conductor on the buttons worn out.. Take the keyfob apart, pull the rubber buttons off the chip, lick your finger and touch the place where the unlock (right side of the fob) would be. That should unlock your doors. I just did it with mine. I would just buy another fob on ebay and change the buttons out.. Hope this works

Apr 23, 2010 | 2007 GMC Yukon Denali

3 Answers

Is it posible to start a yukon denali equiped with keyless entry with a regular copy of the key


it may start but if it does it will not stay running. you are asking for issues.

Dec 11, 2009 | 2003 GMC Yukon Denali

1 Answer

Driver door will not unlock with remote but all other doors does.


does work with your key if so
you remove door panal and lock solniod
see if it has power whan useing remote if so replace solnoid

Jul 08, 2009 | 1999 GMC Yukon

Not finding what you are looking for?
2007 GMC Yukon XL Denali Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...