Question about 2007 Jeep Compass Limited

1 Answer

Just replaced inner tie rod and now when start driving it ma;es an ugly sound and pulls hard to right where i got it replaced. Only going 20 mph .cant drive it... Jeep compass 2007. could itbe that it wasnt put on correctly?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 3,640 Answers

The inner tierod may have been put on wrong, but after any steering system parts have been replaced or fixed. it is a good idea to get it relined this is why it pulls so hard. wheels are not in alignment with each other. get it aligned, and all should be ok. if you leave it. it will wear tire down to nothing, really quick. good-dayt !

Posted on Feb 19, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22156 Answers

SOURCE: Vibration in front end from 50- 60 mph. Not UV

distorted tyres ,jack up and spin and have a good look

Posted on Apr 05, 2010

  • 447 Answers

SOURCE: MY HUSBAND REPAIRED THE OUTER TIE RODS AND BALL

If both the ESP [Electronic Power Steering] and Airbag lamp are on then first I would check to see if something such as an electrical connector may have gotten unhooked down by the tie rod ends. The system isn't seeing the data it should, or is seeing some data it doesn't like, and has turned on both of these warning lamps as a result. I have seen similar problems occur if the steering shaft was disconnected from the steering gear and inadvertently turned a revolution or two before being reconnected. If no wiring problems are found then the system will need to be checked/tested using a scan tool to narrow down what has happened. Hope this helps and good luck!

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Moderate scraping noise coming from my right front tire


a shimmy condition indicates it needs a wheel alignment
best take it to an accredited front end specialist shop for a proper diagnosis of the problem

Jun 22, 2017 | Cars & Trucks

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

Inner tie rod removal


The first step in replacing the inner tie rod is to remove the tie rod end. It's basically a three step process, where you start by loosening the jam nut that's used to set the alignment (toe-in or toe-out). That jam nut determines how far up the inner tie rod the tie rod end is fixed. The tie rod end is hollow and threaded, so it can be screwed on or off the inner tie rod. Any procedure for removing a tie rod will start by telling you to count the turns you unscrew the tie rod end, something that I didn't do, and I'll save the explanation for the end:-) After you loosen the jam nut, you remove the cotter pin from the post on the outer tie rod ball joint, and unscrew the nut that holds the ball joint into the tapered fitting on the steering knuckle (video to right). After you pop the outer tie end free of the steering knuckle, you can unscrew the tie rod end. from the inner tie rod, but you need to grip it with something. Inner tie rods normally have some flat surfaces or a splined surface for grabbing with pliers. In this case, I needed two pairs of visegrips and a clamp to hold the visegrips on the inner tie rod from moving in order to get the outer tie rod end broken free and turning easy. That video is below. I happen to own the shop manuals for my Dodge Omni, so I was able to study the procedure for replacing the inner tie rod in detail. I didn't follow it for a couple reason. First, they show my type of power steering rack (Saginaw vs TRW) needs to be removed from the car to change the inner tie rod. That's a lot of extra work, not to mention the fact I buried one of the crossmember bolts in my unibody and flooring repair! So I went with an inner tie rod removal kit from Harbor Freight, manufactured by U.S. General (in Taiwan). The tool is very simple, basically a large steel tub with a snap in opening for a large crows foot insert on one end and a 1/2" socket drive on the other end. The kit is shown in the photo to the lower left (which I need to replace), and a video of the procedure is shown below. The kit wasn't quite right for my car, I had to use an oversized crows foot and the ball joint housing on the inner tie rod was too long, so the flats on the housing were barely held with the crows foot positioned by hand at the very end of the tool. But I got it out.

Dec 16, 2010 | 1992 Buick LeSabre

1 Answer

How hard is it to replace a outside tie rod end on a 95 dodge neon and how.


take the wheel off, there is a nut on the tie ron locking the tie rod end in place loosen this up (only break it free do not back way off) now take the nut offthe tie rod end that goes into the spindle, Hit the side spindle with a hammer right were the end goes in while pulling up on the tierod end (may take a few hard hits)> Now that you have the end out of the spindle you can unscrew the tie rod end from the inner tierod.*******NOTE*******measure the distance between the locknut on the inner tie rod to the middle of the outer tierod end,You want to keep that same distance or your car will pulll to one side and you'll need a wheel allignment.

Dec 30, 2009 | 1995 Dodge Neon

2 Answers

Am changing the inner tie rod on a 2000 cirrus with a 2.5 and cant figure out how to get old one off


to get the inner tie rod out you need an inner tie rod tool, it's a long tube that fits a 1/2 inch drive rachet and there's different size adaptors that go into the end of it to fit over the tie rod, find the right size put into tool, put over tie rod and brake it loose, reverse for installtion.

Nov 18, 2009 | 2000 Chrysler Cirrus

2 Answers

Any info on tie rods


You have left and right inner tie rods and outer tie rods on your car.
You also have lower ball joints which can wear loose too....not to mention the left and right struts and upper strut bearings.

A cheap (China) tie rod may last only a year.(plastic inner wear points)
A good quality tie rod may last 10.(nylon and/or metal wear points)

Oct 09, 2009 | 1991 Ford Escort

1 Answer

How difficult to replace inner tie rod end on 06 silverado 2wd?


Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Jun 03, 2009 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

Replace rack/pinion


The book calls for about 5 hours labor with a lift, air tools, and experience. It's a tough job. Here are a few tips, Take the lines loose from the rack; not the pump. With the tires off, Remove the nuts from the outer tie rods.Run the nuts back on the tie rods stud and hit the steering knuckle where the tie rod's stud goes through.This will free the stud. Remove the steering shaft from the rack.(take the bolt all the way out.Remove rack mounting bolts. Twist,pull ****,and fight the rack out the side of the car with the most room. The new rack will have inner tie rods already installed. Make sure the new rack is centered.(Turn left then right count the turns then center same # of turns from left to right). Count the threads or measure from the outer tie rod's jam nut to the last thread on the inner tie rod.(you can leave the jam nut in place and take the outer tie rod off and measure from the jam nut to the end of the rod.)Install the outer tie rods. Replace rack in car. hook up steering shaft.Bolt up rack. Hook up lines. Add fluid and work rack back and forth to bleed air. recheck fluid. Have it aligned. (or just take it to a shop.This job is going to be a nightmare!!!)

May 23, 2009 | 1999 Ford Taurus

1 Answer

Shaking problem


shaking problems star.. from front end.. check you tires out of round shape.. balancing tiress. inner and outer tie rods. alignament

Feb 26, 2009 | 1998 Lexus ES 300

Not finding what you are looking for?
2007 Jeep Compass Limited Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...