Question about Infiniti Cars & Trucks

Open Question

How to replace belt tensioner on a 2003 g35 - Infiniti Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: 2003 New Beetle Serpentine Belt Replacement

http://www.mvreader.com/multiview/dayco/catalogSearch.php?autoCatalogSearch=1&make=VOLKSWAGEN&model=BEETLE&year=2003&year_from=&year_to=&engine=All&l=n

This should help. Please Rate My Response! Thanks!

Posted on Feb 04, 2009

  • 73 Answers

SOURCE: adjust serpentine belt tensioner 2003 hyundai

has automatic belt tensioner

Posted on Apr 22, 2009

  • 176 Answers

SOURCE: how do I release the belt tension pully to replace serpentine belt

You can run down to your local auto parts store and buy a serp belt tool. Or you can take a 3/8 drive ratchet, locate the 3/8 square hole in your tensioner and put the ratchet in the hole. For more leverage I put a deep socket over the ratchet handle and put a long 3/8 extention in the deep socket. This will provide ample leverage and will save buying more tools you do not need. Simply move the tensioner to the direction that takes pressure off of the belt.

Posted on May 24, 2009

  • 12 Answers

SOURCE: 2003 Tahoe (5.3). AC belt/tensioner/compressor (Chatters)

The compressor is bad. I have the same problem. Apparently none of the tahoe's compressors are worth a ****! im having to replace mine too. You have to change the compressor, the accumulator/dryer, orifice tube and flush the lines. If you look on ebay you can buy a complete kit to change it all for about 300 bucks. The dealership tells me that you need to change the fan clutch as well. They told me that the reason for the noises is the fan clutch isnt working properly and it lets the compressor get too hot causeing higher pressures in the compressor due to the heat. They called it liquid slugging I believe. Mine doesnt break the belt but when you give it very much gas it makes a squeal and then a grinding noise like your trying to put a standard transmission in gear with it running without pushing in the clutch. I asked if you could just change the fan clutch and they told me no its too late, you have to change the compressor and dryer/orifice tube.

Posted on Jun 23, 2009

  • 8 Answers

SOURCE: need to remove headlight 2003 infinity g35 sedan

yes ballast is on the bottom of the headlight capsule. remove and note 4 torx heads

Posted on Nov 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car makes horrible loud squeaking noises from front end of car under hood when temps reach 95 outside. Could this be suspension related and how serious and expensive.


May be fan belt, check tension by looking 2 c if arrows r within tolerance on the belt tensioner. If arrows r beyond tolerance, replacement is necessary. Or u could push up&dwn on both front fenders (one at a time) 2 hear 4 ur noises. Good luck.

Aug 08, 2015 | 2007 Infiniti G35 Sedan Sport Sedan

1 Answer

2003 Infiniti g35 coupe overheating, replaced radiator, thermostat, and cap, attempted to bleed.. still overheating.


03 INFINITI G35 VQ35 AUTO OVERHEATING - YouTube

? 3:24
www.youtube.com/watch?v=q4QM9X2OzQQ
Oct 6, 2013 - Uploaded by KEVIN KAZEMI
03 INFINITI G35 VQ35 AUTO OVERHEATING. ... Infiniti G35Stereo Removal, Audio Finisher, AC - REPAIR 2003-2004 -

Jul 22, 2015 | Infiniti Cars & Trucks

1 Answer

Strange noises


Most certainly belt or accessory noise. My guess is the tensioning wheel bearing is shot. Take the belt off and see if the tension wheele spins smooth or rattles

Mar 27, 2014 | 2005 Infiniti G35

1 Answer

2003 yukon ac compressor


need a tensioner tool, and pull back on tensioner to give room for new belt

Jul 01, 2012 | 2003 GMC Yukon XL

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    I have a 2003 subaru the left section of my cylinder is making a lot of noise close to the timing belt tension


    Hi and welcome to FixYa!

    If it's close to the timing belt tensioner then you may want to check out the tensioner itself. If the tensioner is worn out this issues can occur. Please replace the timing belt as well when replacing the tensioner.

    Hope this helps and thank you for using FixYa! Have a good one!

    Feb 11, 2011 | 2003 Subaru Outback

    3 Answers

    How to tighten serpentine belt for 2003 Monte Carlo 3.8L


    the belt is self adjusted by a spring loaded automatic belt tensioner, if the belt is noisy or seems loose either the belt size is wrong (if it was replaced recently) or the tensioner is defective or one of the belt idler pulleys is defective.

    May 27, 2010 | 2003 Chevrolet Monte Carlo

    2 Answers

    2003 grand prix belt hangs off tensioner


    It appears that either the new tensioner or some other pulley is NOT lined up properly. Check to make sure all pulleys are in alignment.

    Jan 16, 2010 | 2003 Pontiac Grand Prix

    1 Answer

    How to replace serpentine belt on toyota matrix 2003


    2003–06 1zz-FE Engine & 2003 2zz-FE Engine
    1. Disconnect the negative battery cable.
    2. Use a wrench and rotate the belt tensioner clockwise.
    f81e9e7.gif
    Use a wrench and rotate the belt tensioner clockwise—2003–06 1ZZ-FE engine and 2003 2ZZ-FE engine

    1. With pressure applied to the wrench, and tension relieved from the drive belt, remove the accessory drive belt.
    To install:
    1. Raise and safely support the vehicle.
    2. Remove the right side lower engine splash shield.
    3. Properly route and install the accessory drive belt onto the drive pulleys.
    4. Use a wrench and rotate the belt tensioner clockwise.
    bf314d5.gif
    Use a wrench and rotate the belt tensioner clockwise.

    1. With pressure applied to the wrench, install the accessory drive belt.
    2. With the accessory drive belt installed properly, release the belt tensioner.
    3. Install the right side lower engine splash shield.
    4. Connect the negative battery cable. Tighten the battery cable bolt to 11 ft. lbs. (15 Nm).

    Oct 11, 2009 | 2003 Toyota Matrix

    1 Answer

    Replacing the Drive belt on 2003 Toyota 4runner.


    It uses a spring loaded tensioner. Its not adjustable.

    Jan 10, 2009 | 2003 Toyota 4Runner

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    80 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Infiniti Experts

    yadayada
    yadayada

    Level 3 Expert

    75051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14200 Answers

    Are you an Infiniti Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...