Question about 2006 Nissan Quest

Open Question

Process for oil pan gasket install 2006 nissan quest

Do u need a gasket sealer

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

Ad
  • 16 Answers

SOURCE: I am seeing small puddles of oil under our 96 nissan quest?

you can take it to any auto repair place.Like sears pep boys or a local repair shop. some times you can get away with a few turns on the bolts holding the pan up

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace oil pan gasket


take old pan off, clean all gasket surfaces, install new gasket and RTV sealer to corners, re-install pan.

Aug 13, 2015 | Cars & Trucks

1 Answer

Oil pan gasket, is it metal or cork? There is a


0900c15280070826.jpg

Fig. Fig. 7: Always install a new oil pan gasket on a clean surface-V8 engine shown

  1. Remove the exhaust cross-over pipe.
  2. Remove the left engine-to-transmission strut.
  3. Remove the bolts and lower the oil pan.
  4. Thoroughly clean the gasket mating surfaces.
  5. When installing the pan, always use new gaskets coated with sealer. Apply a drop of RTV silicone sealer where the cork and rubber gaskets meet. On the 5.9L engine, make sure the gasket notches are positioned as shown. Tighten the oil pan bolts to 15 ft. lbs. (20 Nm). Tighten the cross-over pipe to 24 ft. lbs. (32 Nm). this is it no metal you can find this at auto zone libary

Oct 16, 2014 | Cars & Trucks

1 Answer

Oil pan leaks


If it has a gasket, you can see it
with or without the pan on


You still need silicone sealer & the proper
type at the ends of the rear main seal
with a gasket

Need to check a service manual to find out
what is needed

Feb 28, 2013 | 2004 Pontiac Grand Am

1 Answer

Need help to figure out where my 1994 QUEST IS LEAKING?


I would make sure the water pump gasket is not leaking. If the car is blowing white smoke,i would be looking at a blown head gasket.

Oct 12, 2012 | 1994 Nissan Quest

2 Answers

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


  1. timing cover is leaking oil betwwen cover and block
  2. Disconnect the negative battery cable.
  3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
  4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
  5. Remove the accessory drive brackets attached to the timing cover.
  6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
  7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
  8. Remove the timing case cover front seal and gasket from the engine.
  9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
  10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
  11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

To install:

  1. Install a new seal in the timing cover using a suitable seal installation tool.
  2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
  3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
  4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
  5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
  6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
  7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

Do not hammer the damper into place as damage may result to the damper or engine.

  1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
  2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  3. Install the accessory brackets.
  4. Install the fan and fan shroud.
  5. Install the drive belt(s) and adjust to the proper tension.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks
  8. .

Jan 18, 2011 | 1992 Jeep Wrangler

1 Answer

Need to know how to remove oil pan with engine still in vehicle on 96 Ford Wind Star 3.8 engine. What will I have to remove to get access to it.


3.8L Engine Fig. 2: Oil pan assembly - 3.8L engine 89693g43.gif
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Drain and recycle the engine oil.
  4. Remove the oil filter.
  5. Remove the dual converter Y-pipe assembly.
  6. Remove the starter motor.
  7. Remove the engine rear plate/converter housing cover.
  8. Remove the retaining bolts and remove the oil pan. To install:
  9. Clean the gasket mating surfaces thoroughly.
  10. Trial fit oil pan to cylinder block. Ensure that enough clearance has been provided to allow the oil pan to be installed without sealant being scraped off when pan is positioned under the engine.
  11. Apply a bead of silicone sealer to the oil pan flange. Also apply a bead of sealer to the front cover/cylinder block joint and fill the grooves on both sides of the rear main seal cap. NOTE: When using silicone rubber sealer, assembly must occur within 15 minutes after sealer application. After this time, the sealer may start to harden and its sealing effectiveness may be reduced.
  12. Install the oil pan and secure to the block with the attaching screws. Tighten the screws to 80-106 inch lbs. (9-12 Nm).
  13. Install a new oil filter.
  14. Install the engine rear plate/converter housing cover.
  15. Install the starter motor.
  16. Install the Y-pipe converter assembly.
  17. Lower the vehicle.
  18. Fill the engine with oil.
  19. Connect the negative battery cable.
  20. Start the engine and check for leaks. prev.gif next.gif

Oct 15, 2010 | 1996 Ford Windstar

1 Answer

What is the proper procedure to changing an oil pan and can i use an RTV sealer instead of a gasket?


I would suspect that this is an Escort style pan in which RTV is the oil pan gasket. I have always applied a thin layer of RTV to the pan and the block of the engine, allow them to dry for 1/2 hour, then reapply a second thing layer to the oil pan and install. I have never had one leak after using this method. Make sure that the bolt holes stay open during this whole process.

Aug 03, 2010 | Ford ZX2 Cars & Trucks

1 Answer

I have a leak from the oil pan ...of my 1992 mercury topaz and im needing to know what all i will need to do to repair it


You didn't list your engine size so please pick the approriate task:

2.0L Engine
  1. Disconnect the negative battery cable.
  2. Raise the vehicle and support safely with jackstands.
  3. Drain the crankcase of oil.
  4. Remove the attaching bolts securing the oil pan to the engine.
  5. Clean the oil and gasket mating surface completely, and allow to dry.
To install:
  1. Apply a 1/8 in. (3.18mm) bead of silicone sealer D6AZ-19562-B or equivalent between the oil pan and engine crankcase.
  2. Install the oil pan using the attaching bolts. Torque bolt to 5-7 ft. lbs. (7-10 Nm).
  3. Lower vehicle, and fill crankcase with correct amount of engine oil.
  4. Start engine and check for leaks.

2.3L Engine
  1. Disconnect the negative battery cable.
  2. Raise the vehicle and support safely with jackstands.
  3. Drain the crankcase of oil, and drain the cooling system by removing the lower radiator hose.
When draining coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze, and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the roll restrictor if equipped with a manual transaxle.
  2. Disconnect the starter cable.
  3. Remove the starter from the vehicle
  4. Unfasten the bolts securing the rear oil pan to the transaxle case.
  5. If equipped with a manual transaxle, remove the secondary air injection tube at the check valve.
  6. Remove the heater supply tube located at the lower water pump inlet tube assembly.
  7. Loosen the bolts and remove the brackets at the block and water pump inlet tube and A/C compressor line at the pan.
  8. Using a prybar between the engine and body of car, flex engine enough the remove oil pan.
  9. Clean the oil and gasket mating surface completely, and allow to dry.
  10. Clean both mating surfaces of oil pan and cylinder block making certain all traces of RTV sealant are removed. Ensure that the block rails, front cover and rear cover retainer are also clean.
  11. Remove and clean oil pump pick-up tube and screen assembly. After cleaning, install tube and screen assembly.
To install:
  1. Apply a bead of RTV E8AZ-19562-A sealer or equivalent, in the oil pan groove. Completely fill oil pan groove with sealer. Sealer bead should be 0.200 in. (5mm) wide and 0.080-0.150 in. (2.0-3.8mm) high (above oil pan surface) in all areas except the half-rounds. The half-rounds should have a bead 0.200 in. (5mm) wide and 0.150-0.200 in. (3.8-5.1mm) high, above the oil pan surface.
Applying RTV in excess of the specified amount will not improve the sealing of the oil pan, and could cause the oil pickup screen to become clogged with sealer. Use ad equate ventilation when applying sealer.
  1. Install oil pan to cylinder block within 5 minutes to prevent skinning over. RTV needs to cure completely before coming in contact with any engine oil. Ideally, about 1 hour at ambient temperature between 65-75°F (18-24°C) is recommended as a drying time.
  2. Install oil pan bolts lightly until the 2 oil pan-to-transmission bolts can be installed.
  3. Install 2 oil pan-to-transaxle bolts. Tighten to 30-39 ft. lbs. (40-54 Nm) to align oil pan with transaxle. Loosen bolts 1/2 turn.
  4. Tighten all oil pan flange bolts to 15-22 ft. lbs. (20-30 Nm).
  5. Tighten 2 oil pan-to-transmission bolts to 30-39 ft. lbs. (40-54 Nm).
  6. Install brackets for A/C compressor line and water pump inlet tube.
  7. If equipped with a manual transaxle, fasten the air injection tube.
  8. Install the starter and cable.
  9. Lower vehicle.
  10. Install engine oil and coolant.
  11. Connect the negative battery cable.
  12. Start engine and check for coolant and oil leaks.

Oct 12, 2009 | 1992 Mercury Topaz

1 Answer

I am seeing small puddles of oil under our 96 nissan quest?


you can take it to any auto repair place.Like sears pep boys or a local repair shop. some times you can get away with a few turns on the bolts holding the pan up

Jan 19, 2009 | 1993 Nissan Quest

2 Answers

Need torque specs for oil pan gasket


There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Dec 31, 2008 | 1993 Nissan Quest

Not finding what you are looking for?
2006 Nissan Quest Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...