Question about 2000 Chrysler Cirrus

Open Question

How do you replace the rear brakes on a 2000 chrysler cirrus

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Sgt Fluffy
  • 157 Answers

SOURCE: where is the spark plugs located on a 2000 chrysler cirrus.

Follow the ignition wires down.

Posted on Jun 10, 2009

  • 2841 Answers

SOURCE: steering is really stiff after replacing power

Is the drive belt adjusted properly. Did you bleed all air from the system after installing the pump? Start the engine and turn the steering wheel from left to right fully 10 times. This will remove any trapped air. Check the fluid level and top it off.

Posted on Nov 21, 2009

  • 3 Answers

SOURCE: Picture of 1999 Chrysler Cirrus rear disc parking

Parking brake is operated by a cable and not the caliper. Your car has disc brake pads for squeezing the rotor to stop, the parking brake has drum type brake shoes that push out on the inside of the rotor. Changing the disc pads only requires squeezing the piston back in like usual.

Posted on Dec 17, 2009

  • 1024 Answers

SOURCE: cirrus 2000 rear brake jam

if it's drum brake, remove the drum and check for dust collected inside the drum. also check the emergency brake cables for free of rust and are not binding

Posted on May 25, 2010

  • 34 Answers

SOURCE: How to replace water pump

In short, to replace the water pump you need to disassemble a good deal of the passenger side of the engine. Without a lift, this is not a easy job at home. If you really want to do it yourself, I highly recommend you get a Haynes manual for the car. It's invaluable for a large job like this. Just be prepared for a long job. The shop manual for this calls for 5.5 hrs. That's a mechanic with experience, a lift, and all the right tools. One huge suggestion for you though. Replace the timing belt while you are in there. Its a cheap part, and honestly it'll fail someday. This will save you another headache's worth of labor for one little part.

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right rear brakes keeps messing up on a 1998 Chrysler Cirrus, we keep buying new right rear brakes about every two months or less. Can you help us out?


You have to make sure the brake system is operating properly.Change both rear brakes it sounds like the left rear brake side is not working making the right side wear out so quick.After changing the back brakes bleed them making sure you have no air in your brake lines.start bleeding them from the left rear to the right rear to the left front to right front to master cylinder.

Apr 02, 2014 | 1998 Chrysler Cirrus

1 Answer

2000 Chrysler Cirrus LXi 3.6 4 door sedan 4 Disk


check the level of dot 3 oil in the reserves...remember you replaced the lines and air has gotten into it- ti may take a bit to fill caliper..
if this doesnt work there might be a problem with the brakes fluid dispersion- it regulates the amount of fluid to each wheel...

Sep 03, 2013 | 2000 Chrysler Cirrus

1 Answer

Where is the location to bleed brakes on a 1996 chrysler cirrus


Should be a bleeder screw on each cylinder at each wheel.

Aug 20, 2012 | 1996 Chrysler Cirrus

1 Answer

Need photo or video of rear brake assembly 2000 chrysler cirrus


For drum brake related problem,i suggest you to go through this help links.Click the link below for troubleshooting procedure:-----How to service Drum brakes?http://repairhelpcenter.blogspot.in/2012/02/how-to-service-drum-brakes.html--------What type of problems usually noticed on Drum brakes?http://repairhelpcenter.blogspot.in/2012/02/what-type-of-problems-usually-noticed.html---------How to test Drum Brakes?http://repairhelpcenter.blogspot.in/2012/02/how-to-test-drum-brakes.html
---------How to inspect brake drums?http://repairhelpcenter.blogspot.in/2012/02/how-to-inspect-brake-drums.html
---------This will help.Thanks.

Jan 25, 2012 | 2000 Chrysler Cirrus

1 Answer

How do I bleed the brakes on my 2000 chrysler cirrus?


Get a helper. Fill the master cyl reservoir with brake fluid. have helper push brake peddle to the floor and hold it. crack bleeder at the farthest brake caliper from the master cyl. (right rear) close bleeder screw let brake peddle up for about 10 sec. repeat until u get nothing but fluid from bleeder. Don't forget to check reservoir level regularly. If u let it run dry u get to start all over again.

May 16, 2011 | 2000 Chrysler Cirrus

1 Answer

Do a 2000 chrysler cirrus(v6) have brake drums for a rear brake??


the car came with both disk and drum setups on the rear, it depends on what was ordered, the most common is the front disk and rear drum, but many did have the 4 wheel disk setup.

Oct 26, 2010 | 2000 Chrysler Cirrus

1 Answer

Cirrus 2000 rear brake jam


if it's drum brake, remove the drum and check for dust collected inside the drum. also check the emergency brake cables for free of rust and are not binding

May 25, 2010 | 2000 Chrysler Cirrus

1 Answer

Picture of 1999 Chrysler Cirrus rear disc parking brake system. Is parking brake operated by rear caliper? If so, is there a special procedure for moving the piston inward when replacing the brake pads?


Parking brake is operated by a cable and not the caliper. Your car has disc brake pads for squeezing the rotor to stop, the parking brake has drum type brake shoes that push out on the inside of the rotor. Changing the disc pads only requires squeezing the piston back in like usual.

Nov 06, 2009 | 1999 Chrysler Cirrus

1 Answer

CLUNKING SOUND IN REAR UPON APPLYING BRAKES 2000 CIRRUS CAR


I would check the brake caliper hinge pins. If the pins are worn, every time you apply the brakes the caliper moves forward against the pins. If the caliper pins and or caliper are worn they will clunk when the brakes are applied.
Check to see if the caliper shifts forward and back.
Let me know.
Regards,

Apr 09, 2009 | 2000 Chrysler Cirrus

1 Answer

How do I change the spark plugs in 2000 Chrysler Cirrus LXi 2.5L V6?


I did a Google search "How do you replace the rear spark plugs on a 2000 Chrysler Cirrus?" and found this link: http://www.faqs.org/qa/qa-6243.html

I haven't tried it yet and am thinking of purchasing a Chilton manual just in case, but as far as explanations go the one at the very bottom of the page in the link sounds the most legitimate so far.

Besides, I have to pay you guys $9.99 for one answer that I can get for free; or I can get the Chilton and have a whole heap of answers for around $20.

Jul 11, 2008 | 2000 Chrysler Cirrus

Not finding what you are looking for?
2000 Chrysler Cirrus Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...