Question about 2007 Toyota RAV4

Open Question

How to change a water pump 3.5 rav 2007 - 2007 Toyota RAV4

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

duane_wong
  • 6826 Answers

SOURCE: where is the water pump

Water Pump REMOVAL & INSTALLATION 5VZ-FE Engines Fig. 1: The water pump is located on the front of the engine block, behind the timing cover 93163p92.jpg
Fig. 2: Once the retainers are removed, pull the pump away from the block 93163p97.jpg
Fig. 3: Scrape any remaining gasket material from the block before installing the new pump 93163p98.jpg
Fig. 4: Water pump mounting bolt locations 93163p88.jpg
Fig. 5: Front view of the water pump and thermostat housing 93163p99.jpg
WARNING
This procedure requires the removal of the timing belt. This is an extensive procedure requiring precision work, particularly at assembly. For more information, refer to Timing Belt Removal and Installation. Do not attempt to remove the belt without consulting the procedure; extreme engine damage may occur. Fig. 6: Apply sealant to the areas shown 86823pi7.gif
Fig. 7: A and B bolt locations 86823pi8.gif
Fig. 8: Exploded view of the water pump arrangement — 5VZ-FE engine 93163g19.gif

  1. Drain the cooling system.
  2. Remove the timing belt. For additional information, please refer to the following topic(s): Timing Belt Removal and Installation.
  3. Remove the idler pulley.
  4. Remove the thermostat.
  5. Disconnect the oil cooler hose from the pump.
  6. Remove the seven bolts and the tension spring bracket and then remove the water pump. To install:
  7. Clean all parts well. It is good practice to carefully clean all threaded openings, especially those exposed to coolant to remove rust and scale so at assembly, an accurate torque reading is obtained. This is important since gasketless applications like this depend on even clamp loads from the fasteners to avoid distortion and leaks. Remove any old sealer (Toyota calls it packing) from the pump and mounting area of the engine. Keep oil off the mating areas.
  8. Apply Formed In Place Gasket (FIPG) sealer to the pump-to-block mating surface and then tighten the bolts marked A in the illustration to 13 ft. lbs. (18 Nm). Tighten those marked B to 14 ft. lbs. (20 Nm). NOTE: The parts must be installed within 5 minutes of application of the sealant. Otherwise you must remove and reapply the sealer.
  9. Connect the oil cooler hose.
  10. Install the thermostat with a new gasket.
  11. Install the idler pulley.
  12. Install the timing belt.
  13. Install the drive belts and adjust the tension.
  14. Refill the cooling system and check for leaks.
2RZ-FE and 3RZ-FE Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. If equipped with an air conditioning compressor or power steering pump drive belts, it may be necessary to loosen the adjusting bolt, remove the drive belt(s) and move the component(s) out of the way.
  4. Remove the fluid coupling with the fan and water pump pulley.
  5. Remove the water pump. To install:
  6. Clean the gasket mounting surfaces.
  7. Install the replacement water pump using a new gasket.
  8. Install the water pump pulley and fluid coupling with the fan.
  9. Install the removed engine drive belts.
  10. Fill the cooling system.
  11. Connect the negative battery cable. Start the engine and check for leaks.
  12. Bleed the cooling system.
1FZ-FE Engine Fig. 9: Exploded view of the water pump mounting on the 1FZ-FE engine 86823pk0.gif
Fig. 10: Detach the oil cooler hose from the clamp on the fan shroud 86823pk3.gif
prev.gif next.gif

Posted on Jul 13, 2010

  • 12 Answers

SOURCE: Is the water pump on a 2007 rav 4 internal or

Its internal.

Here's a How To: http://www.ehow.com/how_4914451_replace-water-pump-rav.html

Posted on Apr 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is it very difficult to change the cam iol seal on a 2.0 toyota rav 4 1999, and is there anything I should know that the book doesn't tell


pulling the timing belt on older RAV4 engines is a more difficult task but not impossible.

Do you have some experience with timing belts and or cars in general?

Apr 05, 2013 | 1999 Toyota RAV4

1 Answer

I have a 2007 rav 4 the engine light will flash and the rav feels rough the engine or trans won't shift then it stops and works fine


The flashing check engine light means there is a serious problem with the performance of the engine. You need to get the computer scanned for trouble codes next.

Dec 06, 2012 | Toyota RAV4 Cars & Trucks

1 Answer

Is the water pump on a 2007 rav 4 internal or external


Its internal.

Here's a How To: http://www.ehow.com/how_4914451_replace-water-pump-rav.html

Jul 27, 2010 | 2007 Toyota RAV4

1 Answer

Toyota 2007 RAV 4 Transmission Light needs replaced


duh what
that question makes no sence

Jan 22, 2010 | 2007 Toyota RAV4

2 Answers

I have a 2007 Rav 4 with a speedometer that is


Have you changed the size of the tires?

Sep 10, 2009 | 2007 Toyota RAV4

1 Answer

Replace rear wiper 2007 RAV-4?????


Slide a small screwdriver under the tab in the middle of the blade and the arm, while pressing the tab in, pull blade away from the arm, this may need some extra wiggle. Remember you dont want it to fall off when driving..

May 07, 2009 | 2007 Toyota RAV4

2 Answers

97 toyota rav 4 dies at accel.


most likely its your fuel pump. when the rpm's start to drop just give the gas pedal a few pumps and you should be good.

Nov 17, 2008 | 1997 Toyota RAV4

1 Answer

Water pump


It took approximately 45 minutes to remove the alternator, the belt and the water pump. it then took another 45 minutes to put everything back in place. it was extremly easy!

Nov 11, 2008 | 1997 Toyota RAV4

Not finding what you are looking for?
2007 Toyota RAV4 Logo

Related Topics:

792 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...