Question about 2000 Daewoo Leganza

Open Question

Changing transmission fluid on a 2000 daewoo leganza

Instruction on chaning the transmission fluid

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Daewoo Leganza 2000 timing belt broke

there are no manual at napa or any where else except dealer. they want 100+ dollars for one in MI.

Posted on Sep 01, 2008

  • 701 Answers

SOURCE: Need Instructions on removing and replacing a fuel pump for my 2000 daewoo leganza

Hello martin09canc: First thing to do is relieve fuel pressure in the fuel system. Remove the rear seat cushion.Remove the access cover. Disconnect the electrical plug.Would not hurt to disconnect the negative battery cable. This would eliminate any sparks. Remove the sender retaining ring. Lift out the sender unit. Be careful not to spill gas on the carpet. Replace the seal and reverse the operation to install new unit. If you need further help please just ask. Please rate the quality of the answer as it also helps. Thank You for using FixYa. Roger

Posted on Apr 16, 2009

stevenhurc
  • 450 Answers

SOURCE: Gear OIL in Daewoo Leganza SX manual transmission

CHECKING FLUID LEVEL
1. With the vehicle on a level surface and the fluid in the transaxle cold, remove the filler plug and check the fluid level. The fluid should come to the bottom edge of the plug hole.
2. If the level is low, add SAE 80 manual transaxle fluid through the filler plug hole until the fluid begins to run out.
3. Reinstall the filler plug and tighten it securely. The speed gears and the synchronizer parts on this vehicle receive lubrication through specific passages in the mainshaft. It takes 1.8 liters (1.90 quarts) to fill the transaxle completely.
its located next to drive shaft some on left hand side others on right hand side depending what gearbox.
14d8417.jpg

Posted on May 31, 2009

MNfisherman
  • 11896 Answers

SOURCE: need to check transmission fluid

you will have to raise the vehicle. Look on tranny. You will see two plugs, a lower side drain plug and a higher side check/fill plug. Remove higher side plug, stick your finger in the hole. If you can feel the fluid at top of hole, then it is full, if not, then you will have to add some which is always the tricky part.

Posted on Aug 07, 2009

emissionwiz
  • 75030 Answers

SOURCE: how to change a timing belt on a 2000 DAEWOO

Follow these instructions to the letter, if u get this wrong u will bend the valves in the engine.

Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the starter on a 2000 daewood laganza 2.2 leter


Hi Good afternoon,
Best thing to do is to Google "service manual for 2000 daewoo leganza"( should be able to find a free one in pdf). The info you need will be in there. I change starter on my 2001 leganza using the service manual. Hope this helps.

Feb 28, 2015 | 2000 Daewoo Leganza

1 Answer

HOW DO I TROUBLE SHOOT A 2001 DAEWOO LEGANZA AUTOMATIC TRANSMISSION THAT WILL NOT GO INTO GEAR?


Well, if it is full of fluid, and the shifter is moving the transmission linkage then I would think that there is an internal issue with the transmission.

Sep 26, 2014 | 2001 Daewoo Leganza

1 Answer

I need to install catalyic converter on 2000 daewoo leganza


What is the question ?

This is a social web site

We have no parts or instructions or prices

Just a basic exhaust system repair

Oct 19, 2012 | 2000 Daewoo Leganza

1 Answer

Transmission fluid keeps going low in my 2002 daewoo leganza


Then do a through inspection to find the source of the leak.

Aug 29, 2012 | 2002 Daewoo Leganza

1 Answer

Timing setting daewoo leganza


http://www.tradebit.com/filedetail.php/189127366-daewoo-leganza-service-manual

Aug 28, 2012 | 2000 Daewoo Leganza

1 Answer

I have a 01 daewoo leganza where is the drain plug for the automatic transaxle/transmisson to drain the fluid and replace it?


I have a 2000 Leganza. It was far easier to drain the fluid with a suction hose fed down the transmission filler pipe. Less messy too! You also have the benefit of knowing exactly how much you took out and can avoid overfilling it with the fresh fluid.

Jan 18, 2011 | 2001 Daewoo Leganza

2 Answers

Where can i find an automatic transmision filter AW50-40 LE?


It is located inside the transmission. You have to take the Transmission Fluid Pan off, located on the bottom of the Transmission.

Let me know if this helped...

Apr 05, 2010 | 2000 Daewoo Leganza

1 Answer

Gear OIL in Daewoo Leganza SX manual transmission


CHECKING FLUID LEVEL
1. With the vehicle on a level surface and the fluid in the transaxle cold, remove the filler plug and check the fluid level. The fluid should come to the bottom edge of the plug hole.
2. If the level is low, add SAE 80 manual transaxle fluid through the filler plug hole until the fluid begins to run out.
3. Reinstall the filler plug and tighten it securely. The speed gears and the synchronizer parts on this vehicle receive lubrication through specific passages in the mainshaft. It takes 1.8 liters (1.90 quarts) to fill the transaxle completely.
its located next to drive shaft some on left hand side others on right hand side depending what gearbox.
14d8417.jpg

May 30, 2009 | 2000 Daewoo Leganza

Not finding what you are looking for?
2000 Daewoo Leganza Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...