Question about 2004 Mitsubishi Endeavor

Open Question

Front wheel bearing torque specs 2004 endevor

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ewashmidas
  • 362 Answers

SOURCE: torque specs for the main bearings, connecting rods and heads

Here you go...

Connection Rod Nuts: 37-38 Ft Lbs.
Main Bearing Caps: 55-61 Ft Lbs.
And Head Bolts...

1st - step; - 80 ft./lbs. 2nd - step, loosen all bolts; 3rd - step; - 80 ft./lbs.
69de06e.png

Posted on Jan 24, 2009

Ad
oneStan
  • 431 Answers

SOURCE: How or where do I find info to replace front wheel bearings

Timken bearing assembly is what you need. They actually make this all sound so difficult but let me tell you how I just did the same job on my Murano 06 AWD that uses the same type of assembly.
Remove the axle bolt then the wheel, caliper & bracket to remove the rotor. Support the caliper by hanging it from the the strut spring. From the back side, you should be able to remove the speed sensor and if on that model the bolts come froom the back side, there should be just enough room to remove them. that is what holds the hub assembly in place, these aren't pressed into the vehicle, just mounted. I used an axle puller to remove the hub assembly once all of he bolts were loose & it wasn't necessary to remove the ball joint or axle. You need to push the axle through the hub assy & there is a rental tool you can get for that. There was not any excessive pulling to remove the assembly, just tap, tap, tap & it was free, ready for the other to be installed. There is the possibility that you would have to drop the lower ball joint & tie rod end to get access but I didn't have that problem & I looked at your bearing, it looks identical. Good luck.

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs. for a 2006 kia rio5 front wheel bearing?


Product Note: Wheel Bearing -- Wheel Bearing; Axle Nut Torque Spec: 188 ft-lbs / 255Nm.

Oct 02, 2015 | Kia Cars & Trucks

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

Torque Spec


Front wheel bearing hub is 147 ft lbs. Axle nut is 170 ft lbs.

Oct 06, 2012 | 2006 Hyundai Accent

1 Answer

What are mazda 6 wheel bearing torque specification


What is the front axle torque on a 2004 Mazda 6

Mar 17, 2012 | 2004 Mazda 6

1 Answer

Proper torque for bolts on front wheel


The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

1 Answer

How to replace the front wheel bearings on a 2004 silverado- 4 wheel drive?


They are simple bolt-in units, though make sure you remove the axle nut and get it loose before loosening the wheel bearing bolts. Check with a manual or a dealer for the proper torque spec.

Nov 03, 2009 | Chevrolet 1500 Cars & Trucks

2 Answers

What is the torque specs for the front wheel bearing/hub assembly nut on a 2002 ford mustang?


Wheel bearing don't have torque specs (to the best of my knowedge). They have a procedure - in this case it is....
1. With everything clean and packed with grease, snug the bearing lock nut until it stops.
2. Reverse it about 1/8th to 1/4 turn and insert the cotter pin.
Done

Oct 11, 2009 | 2002 Ford Mustang

1 Answer

I need the torque spec for the axle and the axle nut for the front wheel bearing. 2004 gmc yukon 4.8 ltr. 4wd.thank you


Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Aug 17, 2009 | 2004 GMC Yukon

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8755 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...