Question about Cars & Trucks

Open Question

Change display panel bulb in peugeot 206

Panel which should light up heater dials etc does not work, how do i change the bulb for this

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ccrozier_agr
  • 36 Answers

SOURCE: peugeot 206 glowplugs

If your not good at mechanicing I suggest you take the car to someone that is experenced.
The reason I say this that we have loads of cars into the workshop with glowpugs broken in the head of the engine with the result of us having to remove the cylinder head.
What happens is that the tip of the glowplug breaks in the head when being removed if it is not done properly.
There is a way that we have found that they can be removed easily without breaking them.
Firsty run the car engine until warm, then we pour a little Diesel fuel onto each plug & let them sit for 15mins or so.
Then we remove them with a deep socket 1/4" drive so we don't put to much pressure on them.
they should screw out easily but we turn them out 1 whole turn then back a 1/4 add a little more diesel ( thimble full) & gently screw them out.
If they start to get really tight screw in again a little then screw out again.
The nuts that hold on the wires just need to be nipped up with a small 8mm spanner, but do not over tighten.

Posted on Dec 11, 2008

Ad
  • 1986 Answers

SOURCE: How do i change 12v power / cigarette lighter! in a Peugoet 206

The cigarette lighter is connected to a harness that's being the unit. You need to most likely remove the panel that the cigarette lighter is attached to in order to remove the lighter unit out. Once the unit is out, disconnect the wiring harness to exchange it. I don't know how exactly your lighter will come out

Posted on Aug 25, 2009

  • 279 Answers

SOURCE: How to replace Peugeot 206 side light bulb

hi mate you have to twist the bulb holder through 90 degrees to remove it, you might get better access if you remove the screen washer filler neck

Posted on Dec 14, 2009

alicantecoli
  • 22219 Answers

SOURCE: heater on my peugeot 206 only blows cold air

top up the bottle and bleed the heater pipe off ,their is a bleed screw on top of it

Posted on Jan 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the bulbs on the multifunction display of a Peugeot 206


these are not bulbs as such , they are LED'S and as such it is not cost appropriate to try to replace the LED that has gone out so a new unit is the only choice , cars and there components are mainly designed these days to be replaced and not repaired , unless you can find an independant electronic engineer prepaired to undertake this , good luck

Nov 02, 2014 | Peugeot 206 Cars & Trucks

1 Answer

Change bulb in heater controls


you need to remove center dash assembly to unscrew the heater control assembly once you pull out the heater control assembly you should have access to the rear where the tiny bulb is and you will need the number marked on it or in your owners manual in specs lights some auto parts dont have the same size since there are many models and sizes you might have to buy from dealer and they have to order so look around to find one

Aug 05, 2014 | 2004 Peugeot 206 SW

2 Answers

Where is the brake light switch located on a peugeot 206 car


above the panel under the dash on a support bracket above the brake pedal ,twist and turn to remove

Sep 12, 2012 | 2001 Peugeot 206 1.6

1 Answer

Lcd display on my peugeot 206 does not work.


it may be the back light bulbs that need replacing. to check for this simply shine a torch on to the display and you should be able to see the read out.



let me know if this helps


cheers big mike

Mar 29, 2011 | 1983 Peugeot 504

3 Answers

My back light and one of my headlights are not working on my peugeot 206. My boyfriend changed the bulb in the back light but it's still not working. All of the fuses are ok. What else could it be?


Hi mate,
This is a common problem on the rear lights on 206's.
They have a problem with water leaking into the units and over time this corrodes the bulb holders and sometimes the wiring plugs. the only remedy is to replace the bulb holder unit.
As for the head lights they may just require a pair of bulbs.

Dec 10, 2009 | 1986 Peugeot 505

1 Answer

Faulty LCD display


Ok, you can access it but i wouldn`t reccomend it. Pop it out with a screwdriver, there is a bit of clearence at the bottom of the multi function display pop it upwards. Truthfully i would see an auto electrician he or she will prob sort something like this for around £30. My guess is the two the 2 t5w wedge bulbs are loose that light it, or as you say bad wiring,causing it to fail occasionally Good luck.

May 23, 2009 | 1983 Peugeot 504

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

729 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...