Question about 1996 Nissan Sentra

Open Question

Bearing seal leaking on distributor shaftsteps on replacing distributor on 1.6 nissan engine 1994 model year sentra

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

solobaric
  • 22 Answers

SOURCE: front crank seal slight leak

hi!replace the crankshaft oil seal.most of nissan's vehicles use timing chain so just remove the drive blets and the crankshaft pulley.use a screw driver to remove the old oil seal. install a new one.guaranteed the leak will stop.

Posted on Aug 12, 2008

  • 321 Answers

SOURCE: trunk leaking

I'm not sure how you know the weatherstrip isn't leaking,here's what i would do.With a trusted helper,get in the trunk and latch it.Have the helper spray the entire trunk area with a garden hose while you watch for any water leaks.That's the best way to check the weatherstrip for leaks,and it is likely that's where the leak is coming from.

Posted on Aug 23, 2008

  • 2 Answers

SOURCE: My 1993 Nissan Sentra GXE

Have you checked your MAF? Sentra's are famous for them having problems, I havent had an issue with mine yet thank god.

Posted on Oct 03, 2008

  • 95 Answers

SOURCE: nissan sentra gxe 03 rear wheel hub bearing problem

Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Posted on Oct 15, 2008

bitchn65cuda
  • 70 Answers

SOURCE: locate fuel filter on 2007 nissan sentra 2.0 liter engine

its in the gas tank but it doesnt have to be changed!!!YAY

Posted on Apr 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil leaking from toyota camry 1992, 1994 model


You don't say what engine it has. The 4-cyl was a better than the V6 for oil leaks.

The V6 had oil leaks from

-rear bank cam cover gasket

-distributor o-ring seal

-oil filter bracket o-ring seal

-crankshaft nose oil seal (less common)

-rear main bearing oil seal (expensive, just leave it)

The 4 cyl leaked oil from

-distributor o-ring seal

-camshaft cover gasket

-rear main bearing seal (expensive, leave it)

May 21, 2012 | 1991 Toyota Camry

1 Answer

Thermostat replacement 1994 nisan sentra 1.6 eng how to remove and replave


JUST DRAIN COOLANT LEVEL BELOW THE THERMOSTAT. CATCH COOLANT IN A DRAIN PAN UNDER RADIATOR.THEN REMOVE RADIATOR HOSE FROM THERMOSTAT HOUSING ON THE CYLINDER BLOCK.THEN REMOVE THERMOSTAT HOUSING AND THERMOSTAT.CLEAN THERMOSTAT HOUSING SURFACE AND THERMOSTAT HOUSING SEALING SURFACE ON CYLINDER HEAD.INSTALL NEW THERMOSTAT IN PLACE,MAKE SURE THERMOSTAT AIR BLEED HOLE FACING LEFT SIDE UPWARD ON THE ENGINE.SOME THERMOSTAT HAS TOP STAMPED ON IT.MEANING MUST BE FACING UP.WHEN THERMOSTAT IN PLACE.TAKE NEW THERMOSTAT GASKET.PUT SEALER ON BOTH SIDES OF GASKET.THEN.PUT GASKET ON THERMOSTAT HOUSING.THEN PUT HOUSING IN PLACE TORQUE HOUSING BOLTS 16 - 20 FT LBS.WAIT 1 HOUR UNTIL GASKET SEALER CURE.THEN FILL UP COOLANT SYSTEM.BLEED COOLANT SYSTEM AND CHECK FOR LEAKS.

Sep 17, 2010 | 1994 Nissan Sentra 4-Door

1 Answer

Nissan LEC 1994 sentra water leak problem


check your radiator if theres a bubbles while your engine runnin, if theres bubble, it means you overheat. check your cylinder head for warps... also check your fans...

May 09, 2010 | 1996 Nissan Sentra

1 Answer

How to replace the o ring distributor


Remove the spark plug wires from the distributor. Loosen and remove the distributor mounting bolt(s). Pull the distributor out from the head. The o-ring is on the distributor shaft. The old one probably needs to be cut off. The new one will stretch and slide into place over the shaft. Put some engine oil on the o-ring, and re-insert the distributor. You will need to turn the shaft to the right position to get it to fit back in place.

If you suspect that your distributor is leaking oil because of a bad o-ring, a new o-ring may fix the problem. However, make sure that the distributor shaft bearing seal is not leaking. You can check this by removing the distributor cap and looking for oil inside the distributor. If the bearing seal is leaking, replacing the o-ring will not solve the problem. You will need to rebuild or replace the distributor.

Mar 16, 2010 | 1996 Nissan Sentra

2 Answers

I have a 1992 nissan sentra that failed the 15mph part of the smog test because of high Hc's and high NOx so what can i do to fix it.


get oxygen sensor checked,maybe get tune up see if engine is leaning off properly,could be air flow sensor,but needs sensors to be checked

Oct 30, 2009 | 1993 Nissan Sentra 4 Door

1 Answer

How can I disasemble a 1994 Altima distributor? I need to change the internal seal o bearing since it is leaking oil to the inside of the housing.


You do not need to disasemble the entire distributor. Unplug the black electrical connector from the distributor. (with a white marker or correction ink)Mark the screws and dist to maintain the same settings. remove the two main screws, one in the front and one in the rear of the distributor assembly(not on the cap). The Distributor should slide out. These O-ring seals are not sold at the dealers or parts store. They want you to pay over $150+ to replace the entire dist. I brought in the old seal and I was able to match a seal at autozone. It worked. Hopefully this helpd

Jul 03, 2009 | 1993 Nissan Altima

1 Answer

Front crank seal slight leak 1998 nissan sentra


hi!replace the crankshaft oil seal.most of nissan's vehicles use timing chain so just remove the drive blets and the crankshaft pulley.use a screw driver to remove the old oil seal. install a new one.guaranteed the leak will stop.

Aug 11, 2008 | 2002 Nissan Sentra

2 Answers

Nissan sentra gxe 03 rear wheel hub bearing problem


Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Jun 12, 2008 | 2003 Nissan Sentra

Not finding what you are looking for?
1996 Nissan Sentra Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...