Question about 2008 Chrysler Pt Cruiser

1 Answer

How do I remove error code after installing new battery in 2008 PT cruiser

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 37 Answers

Disconnect battery for one hr,reconnect

Posted on Feb 19, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
pkthoege
  • 93 Answers

SOURCE: DIAGNOSTIC code P01A4 for pt cruiser

This doesnt show up for your car and I was wondering if you could either cofirm it with him or get someone else with adifferent brand OBD 2 scanner to pull codes. Is your PT from europe?

Posted on Nov 22, 2008

rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

  • 323 Answers

SOURCE: driver's airbag light on 2007 PT Cruiser convertable

The first code is for "driver seat track position sensor low". The module detects that the sensor input is less than or equal to 0.3 mA. The second code is referring to the first code. I have no idea what the third code is. Basically you have two different communication systems mixed. The 2001 uses the PCI bus system and the 2007 uses the CAN bus which is much faster. The first code is a CAN bus code and the second is a PCI code. As far as the airbag deploying in the event of a collision, I don't believe it will with an active code in the system. I hope this helps.

Posted on May 13, 2009

  • 142 Answers

SOURCE: Need new battery for 2002 PT Cruiser. What type or

go to napa,they'll tell you what u need

Posted on Oct 18, 2009

  • 2 Answers

SOURCE: I have a 2008 pt cruiser. The engine light is on

My PT cruiser is a couple of years older, but I had the same problem. Drove fine, but start-up was erratic for several weeks. By the time  AAA arrived, it usually was working fine. But when it suddenly  started "struggling for power on the freeway and further along on the same trip, lurching (on a city avenue) I drove straight to my mechanic. It WAS the same sensor . . . and car has been driving perfectly ever since he changed it.

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2008 PT Cruiser: battery dead each morning, new battery, alernator & starter check ok. Starts after a boost each morning, starts at noon & at 5pm, but won't start the next morning. Been doing...


Put a test light on the negative battery cable with it unhooked from the battery touch the test light tester side to the negative terminal on the battery .. the test light will illuminate now start pulling fuses .. the test light will dim as u remove the drain ... check and see witch fuse dims the light the most .. check that circuit... its running your battery down

Jan 28, 2014 | 2008 Chrysler Pt Cruiser

2 Answers

Changed battery in 2008 pt cruiser and now mile gauge says error and there is no code taken it every where even dealship and they can't tell me for sure HELP!!!


It takes special equipment to diagnose this, if this dealer is unwilling to perform the needed diagnosis then call up the customer service number of chrysler Corp listed in the owners booklet and explain to them what is going on and ask the factory representative to step in. If the dealer won't guarantee the repair then find another dealer.

Jun 20, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

Got code po340 on 2008 Chrysler PT cruiser. Runs great sometimes when engine light on & rough at other times like not getting gas. Engine light does not come on every day either. Cam sensor or timing...


P0340: Camshaft Position Sensor A - Bank 1 Circuit Malfunction

- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Feb 08, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

Error message came up on inttrument cluster after low/dead battery crank


have code pulled to see what it is parts store will do it for free pull code it may just have something to do with the battery being dead like you said earylier

Dec 18, 2010 | 2008 Chrysler Pt Cruiser

1 Answer

How do i get the error code on a 2008 pt cuiser. i have the malfunction light on underneath the p (park)


open and close the ignition 3 times in 5 seconds
the codes will be display on the cluster

Nov 21, 2010 | 2008 Chrysler Pt Cruiser

1 Answer

I need information on replacing the windsheild wiper switch on my 2006 Chrysler PT Cruiser


it is actually called the multifunction switch

fairly simple...
  • disconnect battery, but make sure you have your radio code or have installed a memory saver
  • remove shroud around steering column
  • disconnect multifunction switch
  • unbolt switch
  • replace switch
  • reverse to install

3b150c5.gif



Jun 03, 2010 | 2006 Chrysler PT Cruiser

3 Answers

2004 chrysler pt cruiser with only 25k miles and i got a codes po300 and po301 misfires any help?


Good place to start, but If you check directly with Chrysler there may be a technical service bulletin, that isn't posted yet. Have the codes cleared when work done, and see what happens.

Mar 01, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Alarm on my PT Cruiser


Being that this is a 2008 pt cruiser, I would take it back to the dealership and let them look the car over!! Should be covered under warranty!!

Dec 07, 2008 | 2008 Chrysler Pt Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...