Question about 1988 Chevrolet Cavalier Z24

Open Question

Do you know where the turn signal relay is located on a 1988 cavalier z24.Its not in the fuse box.

It's not in the regular fuse box under the dash or under the hood

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: turn signal relay switch, 94 s10 chevy blazer

The Turn signal relay on a 94 s10 blazer is located under the cluster area right behind the panel that holds the parking brake release handle you will see it once a couple of trim panels get remove it will be to the right side of the brake release handle

Posted on Dec 03, 2008

SOURCE: 1999 GMC Suburban DRL Work - Headlights/Highbeams Do Not

go to autozone the can help you if you have one they do a lot of things fore nothing including clearing codes

Posted on Feb 21, 2009

GM Elec
  • 1000 Answers

SOURCE: I need to tear down

Below is process for removing and replacing the clutch assembly.
Hope this helps, good luck.
Regards,


REMOVAL & INSTALLATION


See Figures 1, 2 and 3



0900c1528003be16.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Exploded view of the clutch disc and cover assembly

  1. Disconnect the negative battery cable.
  2. If equipped with a cable clutch (1982-84 vehicles), disconnect the cable at the clutch release lever and transaxle, as outlined earlier in this section.
  3. For 1985-94 vehicles remove the sound insulator from inside the vehicle. Disconnect the clutch master cylinder pushrod from the clutch pedal.




0900c1528003be17.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Disconnect the clutch actuator (slave) cylinder line - 1995-96 vehicles
  1. Remove the transaxle, as outlined earlier in this section.
  2. Mark the pressure plate assembly and the flywheel so that they can be assembled in the same position. They were balanced as an assembly at the factory.
  3. Loosen the attaching bolts one turn at a time until spring tension is relieved.
  4. Support the pressure plate and remove the bolts. Remove the pressure plate and clutch disc. Do not disassemble the pressure plate assembly; replace it if defective.
  5. Inspect the flywheel, clutch disc, pressure plate, throwout bearing and the clutch fork and pivot shaft assembly for wear. Replace the parts as required. If the flywheel shows any signs of overheating, or if it is badly grooved or scored, it should be refaced or replaced.




0900c1528003be18.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: You must follow the specified sequence when tightening the pressure plate retaining bolts
To install:
  1. Clean the pressure plate and flywheel mating surfaces thoroughly.
  2. Position the clutch disc and pressure plate into the installed position, and support with a dummy shaft or clutch aligning tool, tool J 29074 or equivalent. The clutch plate is assembled with the damper springs offset toward the transaxle. One side of the factory supplied clutch disc is stamped "Flywheel Side".
  3. Install the pressure plate-to-flywheel bolts. Tighten them in the sequence shown in the accompanying figure, as follows:
    1. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 12 ft. lbs. (16 Nm).
    2. Tighten bolts 1,2,3, then 4,5,6 in the sequence shown to 15-22 ft. lbs. (22-30 Nm) plus an additional 30° turn.
    3. Remove the clutch alignment tool.

  4. Lubricate the outside groove and the inside recess of the release bearing with high temperature grease. Wipe off any excess. Install the release bearing.
  5. Install the transaxle, as outlined earlier in this section.



WARNING When adjusting the cruise control switch, do NOT exert an upward force on the clutch pedal pad of more than 20 lbs. (89 N) or damage to the master cylinder pushrod retaining ring may result.

  1. For 1985-94 vehicles, attach the clutch master cylinder pushrod to the clutch pedal and secure with the retaining clip. If equipped with cruise control, check the switch adjustment at the clutch pedal bracket. Install the sound insulator.
  2. If equipped with a cable clutch, attach the clutch cable at the transaxle and clutch release lever. Check the clutch operation by lifting the clutch pedal up to allow the mechanism to adjust the cable length. Depress the pedal slowly a few times to set the pawl into mesh with the quandrant teeth.


ADJUSTMENTS


All 1982-84 models have a self-adjusting clutch mechanism located on the clutch pedal, eliminating the need for periodic free play adjustments. The self-adjusting mechanism should be inspected periodically as follows:
  1. Depress the clutch pedal and look for the pawl on the self-adjusting mechanism to firmly engage the teeth on the ratchet.
  2. Release the clutch. The pawl should be lifted off of the teeth by the metal stop on the bracket.

On 1985 and later models, the hydraulic clutch system provides automatic clutch adjustment. No adjustment of clutch linkage or pedal position is required.

Posted on May 04, 2009

  • 2 Answers

SOURCE: 96 Chevy Cavalier z24 will not shift gears

i had the same issue with my cavalier 1998. the speed sensor wiring was chafed. fixed the wires and all is ok..hope this helps.

Posted on May 15, 2009

carfreak1217
  • 109 Answers

SOURCE: 2001 chevy cavalier turn signal relay location

Above the brake pedalc956ca0.gif

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump relay located on a 1988 cavalier z24?


Hello,

Fuel Pump Relay Location The Fuel Pump Relay is located Under The Hood, On The Firewall (Drivers Side), Behind The Master Cylinder.

Sincerely,
Joe Kramer

Apr 21, 2015 | Cars & Trucks

1 Answer

Can't find the fuse for 1988 toyota turn signal


  • You have a Nippo Denso turn signal flasher relay. As you are looking at your cabin fuse panel look in the far left bottom spot. You will see a relay there (maybe green or red) that is for the turn signals. It should also be labeled turn signal on the side of it unless it has been replaced with an aftermarket without labeling on it. This is what you need to check. You can get one at the dealership or a salvage yard.

  • Later models put this relay is under the drivers side dash. Lay on the drivers side floorboard and with a flashlight look up under the steering wheel and it's the big relay right there. It's a stickler to get out but they pull right out as well.

  • Hope this helps.

Nov 04, 2011 | 1988 Toyota Pickup

1 Answer

Head lights will not come on, fuse is fine, I can jump the system with another fuse located on the fuse panel. Is there a relay somewhere, where can I get the nomenclatures for the part numbers on the...


There are no relays involved in the headlamp circuits on a 1989 Chevrolet Cavalier Z24.
The headlamp switch gets power on pin "C" (RED wire) from fusible link "A" which attaches to the starter solenoid. The headlamp switch sends the power from pin "D" (YELLOW wire) to the dimmer switch pin "C" and the dimmer switch sends the power either to the high beam lights pin "B" (LIGHT GREEN wire) or the low beam lights pin "D" (TAN wire) depending on which position it is in.

Sep 06, 2011 | 1989 Chevrolet Cavalier

1 Answer

1988 subaru gl can't locate turn signal relay


there is no turn signal flasher or relay, its a combination switch, but there is a fuse, in the fuse box under the dash, the fuse isn't mark well, but says;

BACK
TURN
(4WD-AT)

if you have a gl-10 this fuse also controls power windows,
i had this same issue where my turn signals and my power windows stopped working (but my hazards still worked) and changing this fuse fixed all my issues

Jan 16, 2011 | 1988 Subaru Justy

1 Answer

Need a fuse panel diagram for a 1989 chevy cavalier z24


http://www.v6z24.com/jbodyforum/looking-for-88-z24-fuse-panel-diagram-t108680,highlight,fuse+panel.html

Dec 18, 2010 | 1988 Chevrolet Cavalier Z24

1 Answer

1997 cavalier turn signals


Your left turn signal relay might be out, if i remember correctly, it's located in the fuse box, and is as easy as changing a fuse. If it isnt in the fuse box under your dash then check under the hood, possibly near the battery.

Jan 31, 2010 | 1997 Chevrolet Cavalier

1 Answer

Have a 2002 cavalier Z24 and the cooling fan will not go on. Have a hard code on the engine saying Cooling Fan 1 Control Circuit. checked all the fuses and the relay, all are fine. what might the problem...


there are two coolant temp sensors on this car one controls the fans and one controls the temp guage in the car. one is located near the thermostat housing and the other is usually located in the block. the one near the thermostat housing usually controls the fans. also try to jumper the fan and make sure the fan is working.

Aug 24, 2009 | 1988 Chevrolet Cavalier Z24

1 Answer

Needing a fuse box diagram


wow you need it too huh?i have a 1990 and needed it also..you would never guess where you can get it..and for FREE..your local library has every wiring diagram and fuse diagram you need in the reference section...

Jul 12, 2009 | 1988 Chevrolet Cavalier Z24

1 Answer

1998 Chevy Cavalier Z24 left rear brake/turn lamps will not work


Sometimes even a new bulb will not work. If you have a Digital Multi Meter you can check that you have power going to the rear. I know that sometimes when a vehicle loses a bulb in one end that it can make the other end stop working. With that said, I suggest that you double check to see that the front works. I used to own a 98 Cavalier RS with the 2.2 liter motor and I know that there are fuses under the hood and behind a little door on the drivers side in the car. Might check fuses under the hood also.

Jun 09, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...