Question about 1996 Mazda 626

Open Question

Clutch won't engage on 1996 Mazda 626 with 5 speed transmission

When I put the car in gear and let up on the clutch it won't engage.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
rcampsr
  • 90 Answers

SOURCE: My Mazda 626 Wont go into Drive

Sounds like you have lost the transmission. There are bands that clamp down to lock the transmission into the gear you want. They are controlled by a hydrolic unit located in the trans. The first thing I would do is have a shop pull the trans oil pan and see if it is full of chips of metal. If so you definately have a problem. At the same time they can look at the bands and see if one of them is broken. another cause would be that metal has gotten into the hydrolic valve body and frozen the drive band portion so it will not function. You may also get lucky and have it be an internal adjustment of the drive band. Good Luck, RAC

Posted on Apr 18, 2009

Ad
  • 334 Answers

SOURCE: Need confirmation that 5 Speed Transmission out 1993 Mazda Protege SOHC 1.8 liter Will Bolt up to the Same L-4 Block Engine /Mounts in the 1990 Mazda Protege LX 1.8 liter DOHC

try calling a junkyard and see if they will tell you the enterchange ok good luck

Posted on Apr 18, 2009

motor1258
  • 6674 Answers

SOURCE: cost to replace waterpump on mazda 626 1996

Go to (repairpal.com) and enter all your info & pick repairs for pricing in your area.

Posted on May 03, 2009

  • 11 Answers

SOURCE: Mazda 626 - Hard to shift into gear.

With any vehicle that has a hydraulic clutch, a worn master cylinder or slave cylinder will give this very symptom. First step is to check the fluid in the resivor. If it is low, you will want to check for fluid bypassing the seals. Be sure to check under the rubber dust cover as fluid can collect there and not be readily visible. Also, if the fluid in the resivor is dark colored, it is an indication of the internal seals going bad and you will need to replace the cylinders.

Posted on Aug 17, 2009

  • 1 Answer

SOURCE: 91 mazda 626 erractic idle surge when engine is cold

My '91 626 did the same thing. I tested the throttle position sensor, and it was good so that wasn't it. The other likely culprit is the Idle Speed Control valve, or Idle Air Control valve, which is a $500 part new (more than I paid for the whole car). I pulled one off a 626 at the salvage yard and got it for 3 bucks, put it on (it's an easy DIY, just 4 philips screws holding it to the intake manifold), however I can't be sure that solved the problem, since I haven't run the car much since then. It would seem the most likely cause, tho, and a cheap fix if you go used. Other possibilities: O2 sensor or Mass Air Flow sensor?

Posted on Nov 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car will go in gear but will not move when clutch is released,any ideas will be helpful.thanks


Either the clutch has failed, or something inside the transmission has broken.
Can you shift gears with the engine running and not depressing the clutch ? Can you put the transmission in first gear and move the car by hand ?

Dec 11, 2012 | 1989 Mazda 626

1 Answer

96 mazda 626 not shifting into 4th gear


You basically need the trans rebuilt. The only way the speed sensor could affect any of the shifting problems is if it broke off into the trans. somehow. You could try checking the trans fluid first, or having it changed.

Jul 16, 2012 | 1996 Mazda 626

1 Answer

2000 mazda 626 5 speed manual transmission is stuck in a gear and won't shift out


A clutch problem will not interfere with gear selection when the engine is off and the car stationary.

It does seem like you have a gearbox or gear linkage trouble.

Sep 16, 2017 | 2000 Mazda 626

1 Answer

Clutch pedal goes to floor and will not come up on its own as normal. Clutch does not engage. Cannot shift gears. Happened suddenly with no leading indicators noticed, except a possible change in sounds...


check the fluid level of the clutch resovoir, try bleeding the system out and look for visable leaks.the line you need to look for should go into the side of the transmission, and lead up to a small round resovoir.

Jan 02, 2011 | 1996 Mazda 626

1 Answer

I have a 2001 mazda 626 manual transmission . The car jurk in 1st 2nd 3rd gear . Do u think I should add gear oil. Where do I add the gear oil at


It sounds more like a clutch problem than tranny. You can try the oil in there, but I think the clutch is shot. Check the fluid in the clutch master and make sure it is working right, no slipping, crunching, grinding, the jerking sounds like oil on the clutch. Check it out.

Sep 05, 2010 | 2001 Mazda 626

2 Answers

Mazda 626 'HOLD' light after gear box oil seal was replaced


I have the same problem with my car I think its the torque converter clutch but you should visit a diagonestic machine just to find out

Dec 06, 2008 | 1998 Mazda 626

Not finding what you are looking for?
1996 Mazda 626 Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...