Question about 2008 Toyota Tundra

Open Question

Diagram on how to replace a serpentine drive belt for a toyota tundra 5.7 engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bbtoast
  • 319 Answers

SOURCE: need a diagram for serpentine belt

Click this link, then look at illustration 6-6.

Regards

Brian

Posted on Sep 18, 2008

  • 65 Answers

SOURCE: need belt schematic for 2006 toyota corolla

I can get you a diagram on monday but it goes from the alternator to the power steering pump then around the tensioner pulley then around the crank pulley then to the a/c compressor then pull on the tensioner to give you some slack and slip it on the waterpump.I hope that helps.Let me know if you still need the diagram

Posted on Nov 29, 2008

Mike258
  • 1498 Answers

SOURCE: Serpentine Belt Toyota Rav4

Hi maroon,

  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator. Double check your routing.
  • The tensioner pulley is on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Posted on Dec 14, 2008

MrScary66613
  • 1990 Answers

SOURCE: procedure to change serpentine belt 2006 toyota tacoma?

Here is your Solution!
You will need to Locate the Belt Tensioner. It has a Large Pulley on a Bracket that Has a Bolt in the Middle and a Smaller Pulley that Goes Under the Belt and Holds Tension on it. You will need to get a Wratchet, Socket, and Cheater Bar. Turn the Bolt On the Top Large Pulley with the Wratchet and Cheater Bar. This will Lower the Smaller Pulley So that you will be Able to Remove the Belt. Please Rate My Response! Thanks! P.S. the link below is for the Belt Routing Diagram.
http://www.mvreader.com/multiview/dayco/catalogSearch.php?autoCatalogSearch=1&make=TOYOTA&model=TACOMA&year=2006&year_from=&year_to=&engine=All&l=n

Posted on Feb 06, 2009

yotaguy
  • 232 Answers

SOURCE: timing belt of toyota tundra 2001, V8 motor 4.7

Here's the diagram you need4582d6e.gif

Posted on May 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the alternator on a 2000 tundra 4.7L 4x2 non serpentine configuration


I presume the serpentine belt is in the way. First, disconnect the battery terminal. Then make sure the serpentine belt diagram is readable and remove the serpentine belt. Then release the tension on the alternator belt and remove all the bolts and wiring.

Nov 20, 2014 | 2000 Toyota Tundra

1 Answer

I need a diagram for the serpentine belt on a 2003 Rav4


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 02, 2012 | 2003 Toyota RAV4

2 Answers

Are the timing belt and the serpentine belt the same thing?


No. The timing belt is a toothed belt that drives the camshaft via sprockets on the camshaft and crankshaft; and it is located behind the timing cover and not visible until the cover is removed. The serpentine belt is a long ribbed belt that drives the accessories on the engine, e.g.: the alternator, power steering pump, and A/C compressor etc. It is in the open and visible.

Jun 14, 2011 | 2004 Toyota Tundra

1 Answer

How do you replace the serpentine belt on a 2007 toyota tundra 5.7


one of the idler pulleys is spring loaded ,look carefully to see what one it is then look to see if it has a square drive to put a rachet bar in to release the tension.

Jan 07, 2010 | 2000 Toyota Tundra

2 Answers

Need diagram of drive belt assembly forcaddy


You didn't list your motor size so please pick the applicable diagram:

ba0b112.gif
Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines

9dcebd3.gif
Accessory serpentine belt routing—5.7L engines with A/C

bb89ba7.gif
Accessory serpentine belt routing—5.7L engines without A/C

27f4999.gif
Accessory serpentine belt routing—6.5L Diesel engines

4d67005.gif
Accessory serpentine belt routing—7.4L engines

491a0a4.gif
Accessory serpentine belt routing—8.1L engines

Oct 26, 2009 | 2002 Cadillac Escalade Ext

1 Answer

How to change serpentine belt, 2004 Toyota Tundra


locate tensioner pulley; release tension from belt; remove belt; make sure not to forget how the belt is routed; route belt around all pulleys but tensioner; put tension on tensioner pulley; route belt over tensioner pulley

Oct 03, 2009 | 2004 Toyota Tundra

1 Answer

How do i change a serpentine belt for a 2007


Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Sep 28, 2009 | 2007 Toyota Tundra

Not finding what you are looking for?
2008 Toyota Tundra Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...